ABB ACS550 User Manual page 122

122
Code Description
1605 USER PAR SET CHG
Defines control for changing the user parameter set.
• See parameter 9902
• The drive must be stopped to change User Parameter Sets.
• During a change, the drive will not start.
Note: Always save the User Parameter Set after changing any parameter settings, or performing a motor
identification.
• Whenever the power is cycled, or parameter 9902
saved. Any unsaved changes to a user parameter set are lost.
Note: The value of this parameter (1605) is not included in the User Parameter Sets, and it does not change if User
Parameter Sets change.
Note: You can use a relay output to supervise the selection of User Parameter Set 2.
• See parameter 1401.
0 = – Defines the control panel (using parameter 9902) as the only control for changing User Parameter
NOT SEL
Sets.
1 = 1 – Defines digital input
DI
• The drive loads User Parameter Set 1 on the falling edge of the digital input.
• The drive loads User Parameter Set 2 on the rising edge of the digital input.
• The User Parameter Set changes only when the drive is stopped.
2...6 = 2... 6 – Defines digital input
DI DI
• See 1 above.
DI
-1 = 1( ) – Defines an inverted digital input
DI INV
• The drive loads User Parameter Set 1 on the rising edge of the digital input.
• The drive loads User Parameter Set 2 on the falling edge of the digital input.
• The User Parameter Set changes only when the drive is stopped.
-2...-6 = 2( )...
DI INV DI
• See 1( ) above.
DI INV
1606 LOCAL LOCK
Defines control for the use of the LOC mode. The LOC mode allows drive control from the control panel.
• When
LOCAL LOCK
0 = – Disables the lock. The control panel can select LOC and control the drive.
NOT SEL
1 = 1 – Defines digital input
DI
• Activating the digital input locks out local control.
• De-activating the digital input enable the LOC selection.
2...6 = 2... 6 – Defines digital input
DI DI
• See 1 above.
DI
7 = – Sets the lock. The control panel cannot select LOC and cannot control the drive.
ON
8 = – Defines bit 14 of the Command Word 1 as the control for setting the local lock.
COMM
• The Command Word is supplied through fieldbus communication.
• The Command Word is 0301.
-1 = 1( ) – Defines an inverted digital input
DI INV
• De-activating the digital input locks out local control.
• Activating the digital input enable the LOC selection.
-2...-6 = 2( )...
DI INV DI
• See 1( ) above.
DI INV
1607 PARAM SAVE
Saves all altered parameters to permanent memory.
• Parameters altered through a fieldbus are not automatically saved to permanent memory. To save, you must use
this parameter.
• If 1602
PARAMETER LOCK
must use this parameter.
• If 1602
PARAMETER LOCK
permanent memory.
0 = – Value changes automatically when all parameters are saved.
DONE
1 = ... – Saves altered parameters to permanent memory.
SAVE
Parameters
.
APPLIC MACRO
1 as a control for changing User Parameter Sets.
DI
2... 6 as a control for changing User Parameter Sets.
DI DI
6( ) – Defines an inverted digital input
INV
is active, the control panel cannot change to LOC mode.
1 as the control for setting the local lock.
DI
2... 6 as the control for setting the local lock.
DI DI
6( ) – Defines an inverted digital input
INV
= 2 ( ), parameters altered from the control panel are not saved. To save, you
NOT SAVED
= 1 ( ), parameters altered from the control panel are stored immediately to
OPEN
is changed, the drive loads the last settings
APPLIC MACRO
1 as a control for changing User Parameter Sets.
DI
2... 6 as a control for changing User Parameter Sets.
DI DI
1 as the control for setting the local lock.
DI
2... 6 as the control for setting the local lock.
DI DI
ACS550 User's Manual