Page 1 Cisco ASR 5000 Series Thresholding Configuration Guide Version 12.2 Last Updated April 30, 2012 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-25552-02...
Page 2 ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco Logo are trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and other countries. A listing of Cisco's trademarks can be found at www.cisco.com/go/trademarks.
Page 3: Table Of Contents
Configuring PPP Setup Failure Rate Thresholds ................38 No Resource Call Reject Thresholds ..................... 39 Configuring No Resource Call Reject Thresholds ................39 Content Filtering Thresholds ................41 Configuring Content Filtering Thresholds ....................42 Enabling Thresholds........................... 42 Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 4 FA Service Thresholds ..................69 Configuring FA Service Thresholds ......................70 Saving Your Configuration ........................71 FNG Thresholds ....................73 Configuring FNG Thresholds ........................74 Saving Your Configuration ........................75 HA Service Thresholds ..................77 ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 5 Configuring Per-HA Service Thresholds ..................116 Per-GGSN Service Thresholds ......................117 Configuring Per-GGSN Service Thresholds ..................117 Per-LNS Service Thresholds ........................ 118 Configuring Per-LNS Service Thresholds ..................118 Per-GPRS Service Thresholds ......................119 Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 6 Configuring Total UE Session Thresholds ..................150 Configuring Total Iu Session Thresholds ..................150 Total HSGW Session Thresholds ......................152 Configuring Total HSGW Session Thresholds ................. 152 Total LMA Session Thresholds ......................153 ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 7 Traffic Performance Optimizer Thresholds ..........161 Configuring TPO Thresholds ........................ 162 Enabling TPO Thresholds ........................ 162 Configuring Threshold Poll Interval ....................162 Configuring Thresholds Limits ......................162 Saving Your Configuration........................163 Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 9: About This Guide
About this Guide This document pertains to the features and functionality that run on and/or that are related to the Cisco® ASR 5x00 Chassis. This preface includes the following sections: Conventions Used Contacting Customer Support Additional Information Cisco ASR 5000 Series Thresholding Configuration Guide ▄...
Page 10: Conventions Used
Required keywords and variables are surrounded by braces. They must be entered as part of the keyword command syntax. variable Optional keywords or variables that may or may not be used are surrounded by brackets. keyword variable ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 11 These variables can be used in conjunction with required or optional keywords or variables. For example: { nonce | timestamp } count number_of_packets size number_of_bytes Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 12: Contacting Customer Support
Contacting Customer Support Go to http://www.cisco.com/cisco/web/support/ to submit a service request. A valid Cisco account (username and password) is required to access this site. Please contact your Cisco account representative for additional information. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide...
Page 13: Additional Information
Statistics and Counters Reference Thresholding Configuration Guide SNMP MIB Reference Cisco Web Element Manager Installation and Administration Guide Product-specific and feature-specific administration guides Release Notes that accompany updates and upgrades to StarOS Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02 xiii...
Page 15: Thresholding Overview
HT. A second alarm is generated in period 6 when the count falls beneath LT. The second alarm indicates a “clear” condition. Figure 1. Example of Thresholding Model Time HT = High Threshold LT = Low Threshold Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 16 Total Iu Sessions PDSN Service: Call setup rate A11 Messages failed and discarded PPP send packets discarded Call setup: Number of calls setup Number of call setup failures RP setup failure rate ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 17 SNMP MIB Reference. The generation of specific traps can be enabled or disabled on the system allowing you to view only those traps that are most important to you. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 18 CLI. The following table indicates the reporting mechanisms supported by each of the above models. Table 1. Thresholding Reporting Mechanisms by Model Model SNMP Traps Logs Alarm System Alert Alarm ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 19: Aaa Thresholds
AAA Manager Enables the generation of alarms or alerts when the AAA Manager AAA Manager Request Request Queue Usage request queue usage reaches a specified percentage level. Queue Threshold Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 20: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 21: Aaa Accounting Message Archive Size Thresholds
Configuring AAA Accounting Message Archive Size Threshold Use the following example to configure the accounting message archive size threshold: configure threshold aaa-acct-archive-size <high_thresh> [ clear <low_thresh> ] threshold poll aaa-acct-archive-size interval <time> threshold monitoring aaa-acct-archive-size Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 22: Aaa Accounting Message Archive Queue Size Thresholds
<high_thresh> [ clear <low_thresh> ] threshold aaa-acct-archive-queue-size3 <high_thresh> [ clear <low_thresh> ] threshold monitoring aaa-acct-archive-queue threshold poll aaa-acct-archive-queue-size1 interval <time> threshold poll aaa-acct-archive-queue-size2 interval <time> threshold poll aaa-acct-archive-queue-size3 interval <time> ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 23: Aaa Accounting Failure Thresholds
Configuring AAA Accounting Failure Threshold Use the following example to configure AAA accounting failure threshold: configure threshold aaa-acct-failure <high_thresh> [ clear <low_thresh> ] threshold poll aaa-acct-failure interval <time> threshold monitoring aaa-acct-failure Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 24: Aaa Accounting Failure Rate Thresholds
Configuring AAA Accounting Failure Rate Threshold Use the following example to configure AAA accounting failure rate threshold: configure threshold aaa-acct-failure-rate <high_thresh>[ clear <low_thresh> ] threshold poll aaa-acct-failure-rate interval <time> threshold monitoring aaa-acct-failure ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 25: Aaa Authentication Failure Thresholds
Configuring AAA Authentication Failure Threshold Use the following example to configure AAA authentication failure threshold: configure threshold aaa-auth-failure <high_thresh>[ clear <low_thresh> ] threshold poll aaa-auth-failure interval <time> threshold monitoring aaa-auth-failure Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 26: Aaa Authentication Failure Rate Thresholds
Configuring AAA Authentication Failure Rate Threshold Use the following example for configuring AAA authentication failure rate threshold: configure threshold aaa-auth-failure-rate <high_thresh>[ clear <low_thresh> ] threshold poll aaa-auth-failure-rate interval <time> threshold monitoring aaa-auth-failure ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 27: Aaa Request Message Retry Rate Thresholds
Configuring AAA Authentication Failure Rate Threshold Use the following example for configuring AAA request message retriy rate threshold: configure threshold aaa-retry-rate <high_thresh>[ clear <low_thresh> ] threshold poll aaa-retry-rate interval <time> threshold monitoring aaa-retry-rate Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 28: Aaa Manager Request Queue Threshold
Configuring AAA Manager Request Queue Threshold Use the following example for configuring AAA Manager request queue threshold. configure threshold aaamgr-request-queue <high_thresh>[ clear <low_thresh> ] threshold poll aaamgr-request-queue interval <time> threshold monitoring aaamgr-request-queue ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 29: Asn Gw Service Thresholds
Threshold value the alert or alarm is cleared. If a trigger condition occurs within the polling interval, the alert or alarm is not generated until the end of the polling interval. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 30: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 31: System-Level Asn Gw Service Thresholds
<time> threshold poll asngw-handoff-denial interval <time> threshold poll asngw-max-eap-retry interval <time> threshold poll asngw-network-entry-denial interval <time> threshold poll asngw-r6-invalid-nai interval <time> threshold poll asngw-session-setup-timeout interval <time> threshold poll asngw-session-timeout interval <time> Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 32 ASN GW Service Thresholds ▀ System-Level ASN GW Service Thresholds threshold monitoring asngw ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 33: Call Setup Thresholds
Enables the generation of alerts or alarms based on the number of calls No Resource Call no processing resources being rejected by the system due to insufficient resources (memory and/or Reject Thresholds available session licenses) during the polling interval. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 34: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 35: Call Setup Thresholds
Configuring Call Setup Thresholds Use the following example to configure call setup thresholds: configure threshold call-setup <high_thresh> [ clear <low_thresh> ] threshold poll call-setup interval <time> threshold monitoring call-setup Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 36: Call Setup Failure Thresholds
Configuring Call Setup Failure Thresholds Use the following example for configuring call setup failure thresholding: configure threshold call-setup-failure <high_thresh> [ clear <low_thresh> ] threshold poll call-setup-failure interval <time> threshold monitoring call-setup ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 37: Rp Setup Failure Rate Thresholds
Configuring RP Setup Failure Rate Thresholds Use the following example for configuring RP setup failure rate thresholding: configure threshold rp-setup-fail-rate <high_thresh> [ clear <low_thresh> ] threshold poll rp-setup-fail-rate interval <time> threshold monitoring call-setup Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 38: Ppp Setup Failure Rate Thresholds
Configuring PPP Setup Failure Rate Thresholds Use the following example for configuring PPP setup failure rate thresholding: configure threshold ppp-setup-fail-rate <high_thresh> [ clear <low_thresh> ] threshold poll ppp-setup-fail-rate interval <time> threshold monitoring call-setup ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 39: No Resource Call Reject Thresholds
Configuring No Resource Call Reject Thresholds Use the following example for configuring no resource call reject thresholding: configure threshold call-reject-no-resource <high_thresh> [ clear <low_thresh> ] threshold poll call-reject-no-resource interval <time> threshold monitoring call-setup Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 41: Content Filtering Thresholds
Default value is 0, which means there will be no monitoring. The polling interval is in seconds and it is an integer between 30 and 60000. Entries will be rounded up to the nearest 30 seconds. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 42: Configuring Content Filtering Thresholds
<interval> Configuring Threshold Limits To configure threshold limits use the following configuration: configure threshold contfilt-block <high_thresh> [ clear <low_thresh> ] threshold contfilt-rating <high_thresh> [ clear <low_thresh> ] ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 43: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 45: Cpu Resource Thresholds
Enables the generation of critical-level alerts or alarms based on ORBS Software Task CPU critical the percentage CPU resources utilized by the Object Request Usage Critical-Level Thresholds Broker (ORB) software task. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 46: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 47: 10-Second Average Of Total Processing Card Cpu Utilization Thresholds
Configuring 10-second Average of Processing Card CPU Thresholds Use the following example for configuring 10-second average of total CPU utilization thresholding. configure threshold 10sec-cpu-utilization <high_thresh> [ clear <low_thresh> ] threshold poll 10sec-cpu-utilization interval <time> threshold monitoring cpu-resource Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 48: Processing Card Cpu Available Memory Thresholds
Configuring Processing Card CPU Available Memory Thresholds Use the following example for configuring processing card CPU available memory thresholding. configure threshold cpu-available-memory <low_thresh> [ clear <high_thresh> ] threshold poll cpu-available-memory interval <time> threshold monitoring cpu-resource ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 49: Processing Card Cpu Load Thresholds
Configuring Processing Card CPU Load Thresholds Use the following example for configuring processing card CPU load thresholding. configure threshold cpu-load <high_thresh> [ clear <low_thresh> ] threshold poll cpu-load interval <time> threshold monitoring cpu-resource Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 50: Processing Card Cpu Memory Usage Thresholds
Configuring Processing Card CPU Memory Usage Thresholds Use the following example for configuring processing card CPU memory usage thresholding. configure threshold cpu-memory-usage <high_thresh> [ clear <low_thresh> ] threshold poll cpu-memory-usage interval <time> threshold monitoring cpu-resource ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 51: Processing Card Cpu Session Throughput Thresholds
Configuring Processing Card CPU Session Throughput Thresholds Use the following example for configuring processing card CPU session throughput thresholding. configure threshold cpu-session-throughput <high_thresh> [ clear <low_thresh> ] threshold poll cpu-session-throughput interval <time> threshold monitoring cpu-session-throughput Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 52: Processing Card Cpu Utilization Thresholds
Configuring Processing Card CPU Utilization Thresholds Use the following example for configuring processing card CPU utilization thresholding. configure threshold cpu-utilization <high_thresh> [ clear <low_thresh> ] threshold poll cpu-utilization interval <time> threshold monitoring cpu-resource ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 53: System Management Card Cpu Memory Usage Thresholds
Configuring System Management Card CPU Memory Usage Thresholds Use the following example for configuring system management card CPU memory usage thresholding. configure threshold mgmt-cpu-memory-usage <high_thresh> [ clear <low_thresh> ] threshold poll mgmt-cpu-memory-usage interval <time> threshold monitoring cpu-resource Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 54: System Management Card Cpu Utilization Thresholds
Configuring System Management Card CPU Utilization Thresholds Use the following example for configuring system management card CPU utilization thresholding. configure threshold mgmt-cpu-utilization <high_thresh> [ clear <low_thresh> ] threshold poll mgmt-cpu-utilization interval <time> threshold monitoring cpu-resource ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 55: Orbs Software Task Cpu Usage Warning-Level Thresholds
Configuring ORBS Software Task CPU Usage Warning-Level Thresholds Use the following example for configuring warning-level ORB software task CPU usage thresholding. configure threshold cpu-orbs-warn <high_thresh> [ clear <low_thresh> ] threshold poll cpu-orbs-warn interval <time> threshold monitoring cpu-resource Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 56: Orbs Software Task Cpu Usage Critical-Level Thresholds
Configuring ORBS Software Task CPU Usage Critical-Level Thresholds Use the following example for configuring critical-level ORB software task CPU usage thresholding. configure threshold cpu-orbs-crit <high_thresh> [ clear <low_thresh> ] threshold poll cpu-orbs-crit interval <time> threshold monitoring cpu-resource ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 57: Cscf Service Thresholds
If a trigger condition occurs within the polling interval, the alert or alarm is not generated until the end of the polling interval. Polling intervals are set on a system level. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 58: Configuring Cscf Thresholds
Use the following example to configure these thresholds: configuration context <context_name> cscf-service <name> threshold call-setup-failures <high_thresh> [ clear <low_thresh>] threshold call-total-active <high_thresh> [ clear <low_thresh> ] threshold error-no-resource <high_thresh> [ clear <low_thresh>] ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 59: Configuring Threshold Poll Intervals
<dur> threshold poll cscf-invite-rcvd interval <dur> threshold poll cscf-reg-rcvd interval <dur> threshold poll cscf-service-route-failures interval <dur> threshold poll error-no-resource interval <dur> threshold poll error-presence interval <dur> threshold poll error-reg-auth interval <dur> Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 60 CSCF Service Thresholds ▀ Configuring CSCF Thresholds threshold poll error-tcp interval <dur> threshold poll reg-total-active interval <dur> ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 61: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 63: Diameter Thresholds
Threshold Diameter Retry Enables generation of alerts or alarms based on the percentage of Diameter requests Diameter Retry Rate Rate that were re-tried during a polling interval. Threshold Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 64: Configuring Diameter Thresholds
If a trigger condition occurs within the polling interval, the alert or alarm will not be generated until the end of the polling interval. Configuring DCCA Protocol Errors Threshold To configure the DCCA Protocol Errors threshold use the following configuration: configure ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 65: Dcca Rating Failure Threshold
If a trigger condition occurs within the polling interval, the alert or alarm will not be generated until the end of the polling interval. Configuring DCCA Unknown Rating Group Threshold To configure the DCCA Unknown Rating Group threshold use the following configuration: configure Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 66: Diameter Retry Rate Threshold
Configuring Diameter Retry Rate Threshold To configure the Diameter Retry Rate threshold use the following configuration: configure threshold diameter diameter-retry-rate <high_thresh> [ clear <low_thresh> ] threshold poll diameter-retry-rate interval <seconds> threshold monitoring diameter ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 67: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 69: Fa Service Thresholds
Clear condition: Actual number of errors < Low Threshold If a trigger condition occurs within the polling interval, the alert or alarm is not generated until the end of the polling interval. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 70: Configuring Fa Service Thresholds
Use the following example to configure the threshold, set the polling interval for the threshold and enable monitoring of the threshold. configure context <context_name> fa-service <name> threshold reg-reply-error <high_thresh> [ clear <low_thresh> ] exit exit threshold poll fa-reg-reply-error interval <time> threshold monitoring fa-service ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 71: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 73: Fng Thresholds
The default value is 0, which means there will be no monitoring. The polling interval is in seconds and it is an integer between 30 and 60000. Entries will be rounded up to the nearest 30 seconds. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 74: Configuring Fng Thresholds
The following example configures a monitoring threshold of 300000 active and inactive FNG sessions on an ASR 5000 chassis: threshold fng-current-sessions 300000 This turns out to be too many, so the following command clears 100000: threshold fng-current-sessions 300000 clear 100000 ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 75: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 77: Ha Service Thresholds
HA services send and receive registration messages. The thresholds in the HA Service- HA Service-Level HA Service- Level can be configured to monitor thresholds for registration reply, re-registration reply, Service Thresholds Level and de-registration reply errors. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 78: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 79: Context-Level Ha Service Thresholds
Use the following example to configure the threshold, set the polling interval for the threshold and enable monitoring of the threshold: configuration context <context_name> threshold ha-service-init-rrq-rcvd-rate <high_thresh> [ clear <low_thresh> exit threshold poll <threshold_name> interval <time> threshold monitoring ha-service threshold monitoring ip-sec Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 80: Ha Service-Level Ha Service Thresholds
| reg-reply-error | rereg-reply-error } exit exit threshold poll ha-init-rrq-rcvd-rate interval <time> threshold poll reg-reply-error interval <time> threshold poll rereg-reply-error interval <time> threshold poll dereg-reply-error interval <time> threshold monitoring ha-service ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 81: Ip Pool Utilization Thresholds
IP Pool: The following thresholds can be configured for all IP address pools configured within Context-Level IP a given system context: Pool and Group Thresholds Percent-free; Percent-hold; Percent-release; Percent-used. NOTE: Separate alerts or alarms are generated for each pool that experiences an event. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 82 (if configured). In the event that two IP address pools belonging to the same pool group are configured with different group-available thresholds, the system uses the pool configuration that has the Enter condition that would be encountered first for the entire group. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 83: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 84: Context-Level Ip Pool And Group Thresholds
<low_thresh> [ clear <high_thresh> ] threshold ip-pool-hold <high_thresh> [ clear <low_thresh> ] threshold ip-pool-release <high_thresh> [ clear <low_thresh> ] threshold ip-pool-used <high_thresh> [ clear <low_thresh> ] threshold monitoring available-ip-pool-group ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 85: Ip Address Pool-Level Thresholds
<low_thresh> [ clear <high_thresh> ] ip pool name alert-threshold pool-free <low_thresh> [ clear <high_thresh> ] ip pool name alert-threshold pool-hold <high_thresh> [ clear <low_thresh> ] ip pool name alert-threshold pool-release <high_thresh> [ clear <low_thresh>] Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 86 IP Pool Utilization Thresholds ▀ IP Address Pool-Level Thresholds ip pool name alert-threshold pool-used <high_thresh> [ clear <low_thresh> ] exit threshold monitoring available-ip-pool-group ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 87: Mme Service Thresholds
Threshold value the alert or alarm is cleared. If a trigger condition occurs within the polling interval, the alert or alarm is not generated until the end of the polling interval. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 88: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 89: System-Level Mme Service Thresholds
<high_thresh> [ clear <low_thresh> ] threshold total-mme-sessions <high_thresh> [ clear <low_thresh>] threshold poll mme-auth-failure interval <dur> threshold poll mme-attach-failure interval <dur> threshold poll total-mme-session interval <dur> threshold monitoring mme-service Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 91: Network Address Translation Thresholds
Default value is 0, which means there will be no monitoring. The polling interval is in seconds and it is an integer between 30 and 60000. Entries will be rounded up to the nearest 30 seconds. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 92: Configuring Nat Thresholds
Configuring Thresholds Limits To configure threshold limits use the following configuration: configure context <context_name> threshold ip-pool-free <high_thresh> [ clear <low_thresh> ] ip-pool-hold <high_thresh> [ clear <low_thresh> ] ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 93 IP pools in the context Thresholds configured using the keyword are specific to the pool that they are configured alert-threshold in, and will take priority, i.e. will override the context-wide configuration mentioned above. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 94: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 95: Packet Processing Thresholds
ACL rules during the polling interval. Thresholds Packets forwarded Enables the generation of alerts or alarms based on the total number of packets Forwarded Packet that were forwarded to the CPU during the polling interval. Thresholds Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 96: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 97: Filtered/Dropped Packet Thresholds
These instructions assume that ACLs have been previously configured. Configuring Filtered/Dropped Packet Thresholds Use the following example to configure the filtered/dropped packet thresholds: configure threshold packets-filtered-dropped <high_thresh> [ clear <low_thresh>] threshold poll packets-filtered-dropped interval <time> threshold monitoring packets-filtered-dropped Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 98: Forwarded Packet Thresholds
Configuring Forwarded Packet Thresholds Use the following example to configure the forwarded packet thresholds: configure threshold packets-forwarded-to-cpu <high_thresh> [ clear <low_thresh> ] threshold poll packets-forwarded-to-cpu interval <time> threshold monitoring packets-forwarded-to-cpu ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 99: Pdg/Ttg Thresholds
Default value is 0, which means there will be no monitoring. The polling interval is in seconds and it is an integer between 30 and 60000. Entries will be rounded up to the nearest 30 seconds. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 100: Configuring Pdg/Ttg Thresholds
[ default ] threshold pdg-current-sessions <high_thresh> [ clear <low_thresh> ] [ default ] threshold poll pdg-current-sessions interval <time> [ default ] threshold pdg-current-active-sessions <high_thresh> [ clear <low_thresh> [ default ] threshold poll pdg-current-active-sessions interval <time> ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 101: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 103: Pdif Thresholds
Default value is 0, which means there will be no monitoring. The polling interval is in seconds and it is an integer between 30 and 60000. Entries will be rounded up to the nearest 30 seconds. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 104: Configuring Pdif Thresholds
[ <high_thresh> clear <low_thresh> ] default threshold { pdif-current-sessions | pdif-current-active-sessions } threshold poll { pdif-current-sessions | pdif-current-active-sessions } interval <time> default threshold poll { pdif-current-sessions | pdif-current-active-sessions } ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 105: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 107: Pdsn Service Thresholds
PDSN Service-Level can be configured to monitor thresholds for A11 registration Level PDSN Level response failures, discarded A11 registration requests, discarded A11 registration Service Thresholds acknowledgments, and discarded PPP send packets for individual PDSN services. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 108: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 109: Context-Level Pdsn Service Thresholds
<context_name> threshold pdsn-service init-rrq-rcvd-rate <high_thresh> [ clear <low_thresh>] exit threshold poll pdsn-init-rrq-rcvd-rate interval <time> threshold monitoring pdsn-service Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 110: Pdsn Service-Level Pdsn Service Thresholds
<high_thresh> [ clear <low_thresh>] exit exit threshold poll pdsn-init-rrq-rcvd-rate interval <time> threshold poll a11-rrp-failure interval <time> threshold poll a11-rrq-msg-discard interval <time> threshold poll a11-rac-msg-discard interval <time> threshold poll a11-ppp-send-discard interval <time> threshold monitoring pdsn-service ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 111 PDSN Service Thresholds PDSN Service-Level PDSN Service Thresholds ▀ Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 113: Per-Service Session Thresholds
Enables the generation of alerts or alarms based on the number of SGSN sessions or the Per-SGSN Service Services number of SGSN PDP contexts (active and dormant) facilitated by any SGSN service Thresholds counted during the polling interval. Per-SGSN Service PDP Contexts Thresholds Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 114: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 115: Per-Pdsn Service Thresholds
Global Configuration mode: Configuring Per-PDSN Service Thresholds Use the following example to configure the per-PDSN service thresholds: configure threshold per-service-pdsn-sessions <high_thresh> [ clear <low_thresh> ] threshold poll per-service-pdsn-sessions interval <time> threshold monitoring subscriber Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 116: Per-Ha Service Thresholds
Configuring Per-HA Service Thresholds Configure the per-HA service thresholds by entering the following command: configure threshold per-service-ha-sessions <high_thresh> [ clear <low_thresh> ] threshold poll per-service-ha-sessions interval <time> threshold monitoring subscriber ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 117: Per-Ggsn Service Thresholds
Configuring Per-GGSN Service Thresholds Use the following example to configure the per-GGSN service thresholds: configure threshold per-service-ggsn-sessions <high_thresh> [ clear <low_thresh> ] threshold poll per-service-ggsn-sessions interval <time> threshold monitoring subscriber Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 118: Per-Lns Service Thresholds
Configuring Per-LNS Service Thresholds Use the following example to configure the per-LNS service thresholds: configure threshold per-service-lns-sessions <high_thresh> [ clear <low_thresh> ] threshold poll per-service-lns-sessions interval <time> threshold monitoring subscriber ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 119: Per-Gprs Service Thresholds
Configuring Per-GPRS Service Thresholds Use the following example to configure the per-GGSN service thresholds: configure threshold per-service-gprs-sessions <high_thresh> [ clear <low_thresh> ] threshold poll per-service-gprs-sessions interval <time> threshold monitoring subscriber Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 120: Per-Gprs Service Pdp Contexts Thresholds
Configuring Per-GPRS Service PDP Contexts Thresholds Use the following example to configure the per-GPRS service PDP contexts thresholds: configure threshold per-service-gprs-pdp-sessions <high_thresh> [ clear <low_thresh> ] threshold poll per-service-gprs-pdp sessions interval <time> threshold monitoring subscriber ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 121: Per-Sgsn Service Thresholds
Configuring Per-SGSN Service Thresholds Use the following example to configure the per-SGSN service thresholds: configure threshold per-service-sgsn-sessions <high_thresh> [ clear <low_thresh> ] threshold poll per-service-sgsn-sessions interval <time> threshold monitoring subscriber Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 122: Per-Sgsn Service Pdp Contexts Thresholds
Configuring Per-SGSN Service PDP Contexts Thresholds Use the following example to configure the per-SGSN service PDP contexts thresholds: configure threshold per-service-sgsn-pdp-sessions <high_thresh> [ clear<low_thresh> ] threshold poll per-service-sgsn-pdp sessions interval <time> threshold monitoring subscriber ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 123: Port Utilization Thresholds
Ports configured for half-duplex do not differentiate between data received and data transmitted. (The transmitted and received percentages are combined.) Therefore, to avoid redundant alarms, it is recommended that only the receive or transmit utilization threshold be configured. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 124: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 125: Receive Port Utilization Thresholds
Use the following example to configure the polling interval over which to measure receive port utilization configure threshold poll port-rx-utilization interval <seconds> port <port-type> <slot#/port#> threshold rx-utilization <high_thresh_%> [ clear <low_thresh_%> ] threshold monitoring Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 126: Transmit Port Utilization Thresholds
Use the following example to configure the polling interval over which to measure transmit port utilization: configure threshold poll port-tx-utilization interval <seconds> port <port-type> <slot#/port#> threshold tx-utilization <high_thresh_%> [ clear <low_thresh_%> ] threshold monitoring ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 127: High Port Activity Thresholds
Use the following example to configure the polling interval over which to measure for high port activity: configure threshold poll port-high-activity interval <time> port <port-type> <slot#/port#> threshold high-activity <high_thresh_%> [ clear <low_thresh_%> ] threshold monitoring Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 129: Session License Utilization Thresholds
Clear condition: Actual session license utilization percentage per session type > High Threshold If a trigger condition occurs within the polling interval, the alert or alarm will not be generated until the end of the polling interval. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 130: Configuring Session License Utilization Thresholds
Configuring Session License Utilization Thresholds Use the following example to configure the thresholds for session license utilization: configure threshold license-remaining-sessions <low_thresh> [ clear <high_thresh> ] threshold poll license-remaining-sessions interval <time> threshold monitoring license ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 131: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 133: Stateful Firewall Thresholds
Default value is 0, which means there will be no monitoring. The polling interval is in seconds and it is an integer between 30 and 60000. Entries will be rounded up to the nearest 30 seconds. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 134: Configuring Stateful Firewall Thresholds
To configure threshold limits use the following configuration: configure threshold fw-deny-rule <high_thresh> [ clear <low_thresh> ] threshold fw-dos-attack <high_thresh> [ clear <low_thresh> ] threshold fw-drop-packet <high_thresh> [ clear <low_thresh> ] threshold fw-no-rule <high_thresh> [ clear <low_thresh> ] ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 135: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 137: Subscriber Thresholds
(active and dormant) counted during the polling interval. Thresholds Active Enables the generation of alerts or alarms based on the total number of subscribers with Active Subscriber subscribers active sessions counted during the polling interval. Thresholds Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 138: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 139: Total Subscriber Thresholds
Configuring Total Subscriber Thresholds Use the following example to configure the total subscriber thresholds: configure threshold subscriber total <high_thresh> [ clear <low_thresh> ] threshold poll total-subscriber interval <time> threshold monitoring subscriber Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 140: Active Subscriber Thresholds
Configuring Active Subscriber Thresholds Use the following example to configure the active subscriber thresholds: configure threshold subscriber active <high_thresh> [ clear <low_thresh> ] threshold poll active-subscriber interval <time> threshold monitoring subscriber ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 141: System Management Card Compactflash Memory Thresholds
Clear condition: Actual percentage memory utilization < Low Threshold If a trigger condition occurs within the polling interval, the alert or alarm will not be generated until the end of the polling interval. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 142: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 143: Total Session Thresholds
Enables the generation of alerts or alarms based on the total number of sessions (active Total S-GW Session Service and dormant) facilitated by all S-GW services counted during the polling interval. Thresholds Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 144: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 145: Total Pdsn Session Thresholds
Configuring Total PDSN Session Thresholds Use the following example to configure the total PDSN session thresholds: configure threshold total-pdsn-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-pdsn-sessions interval <time> threshold monitoring subscriber Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 146: Total Ggsn Session Thresholds
If a trigger condition occurs within the polling interval, the alert or alarm will not be generated until the end of the polling interval. Configuring Total GGSN Session Thresholds Use the following example to configure the per-GGSN service thresholds: configure threshold total-ggsn-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-ggsn-sessions interval <time> ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 147: Total Gprs Session Thresholds
If a trigger condition occurs within the polling interval, the alert or alarm will not be generated until the end of the polling interval. Configuring Total GPRS Session Thresholds Use the following example to configure the per-SGSN service thresholds: configure threshold total-gprs-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-gprs-sessions interval <time> Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 148: Total Gprs Pdp Contexts Thresholds
If a trigger condition occurs within the polling interval, the alert or alarm will not be generated until the end of the polling interval. Configuring Total GPRS PDP Context Thresholds Use the following example to configure the per-GPRS service thresholds: configure threshold total-gprs-pdp-sessions <high_thresh> [ clear <low_thresh>] threshold poll total-gprs-pdp-sessions interval <time> ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 149: Total Ha Session Thresholds
Configuring Total HA Session Thresholds Use the following example to configure the total HA session thresholds: configure threshold total-ha-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-ha-sessions interval <time> threshold monitoring subscriber Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 150: Total Hnb-Gw Session Thresholds
Configuring Total Iu Session Thresholds Use the following example to configure the thresholds for total IuPS and/or IuCS sessions over Iu interface between HNB-GW and CN node: configure ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 151 Total Session Thresholds Total HNB-GW Session Thresholds ▀ threshold total-hnbgw-iu-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-hnbgw-iu-sessions interval <time> threshold monitoring hnbgw-service Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 152: Total Hsgw Session Thresholds
Configuring Total HSGW Session Thresholds Use the following example to configure the total HSGW session thresholds: configure threshold total-hsgw-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-hsgw-sessions interval <time> threshold monitoring hsgw-service ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 153: Total Lma Session Thresholds
Configuring Total LMA Session Thresholds Use the following example to configure the total LMA session thresholds: configure threshold total-lma-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-lma-sessions interval <time> threshold monitoring lma-service Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 154: Total Lns Session Thresholds
Configuring Total LNS Session Thresholds Use the following example to configure the total LNS session thresholds: configure threshold total-lns-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-lns-sessions interval <time> threshold monitoring subscriber ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 155: Total Mme Session Thresholds
Configuring Total MME Session Thresholds Use the following example to configure the total P-GW session thresholds: configure threshold total-mme-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-mme-sessions interval <time> threshold monitoring mme-service Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 156: Total P-Gw Session Thresholds
Configuring Total P-GW Session Thresholds Use the following example to configure the total P-GW session thresholds: configure threshold total-pgw-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-pgw-sessions interval <time> threshold monitoring pgw-service ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 157: Total Sgsn Session Thresholds
If a trigger condition occurs within the polling interval, the alert or alarm will not be generated until the end of the polling interval. Configuring Total SGSN Session Thresholds Use the following example to configure the per-SGSN service thresholds: configure threshold total-sgsn-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-sgsn-sessions interval <time> Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 158: Total Sgsn Pdp Contexts Thresholds
If a trigger condition occurs within the polling interval, the alert or alarm will not be generated until the end of the polling interval. Configuring Total SGSN PDP Context Thresholds Use the following example to configure the per-SGSN service thresholds: configure threshold total-sgsn-pdp-sessions <high_thresh> [ clear <low_thresh>] threshold poll total-sgsn-pdp-sessions interval <time> ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 159: Total S-Gw Session Thresholds
Configuring Total S-GW Session Thresholds Use the following example to configure the total S-GW session thresholds: configure threshold total-sgw-sessions <high_thresh> [ clear <low_thresh> ] threshold poll total-sgw-sessions interval <time> threshold monitoring sgw-service Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 161: Traffic Performance Optimizer Thresholds
The polling interval is in seconds and it is an integer between 30 and 60000. Entries will be rounded up to the nearest 30 seconds. The default interval value is 900 seconds. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...
Page 162: Configuring Tpo Thresholds
<interval> Configuring Thresholds Limits To configure threshold limits use the following configuration: configure threshold tpo-dns-failure <high_thresh> clear <low_thresh> threshold tpo-low-compression-gain <high_thresh> clear <low_thresh> threshold tpo-rto-timeout <high_thresh> clear <low_thresh> ▄ Cisco ASR 5000 Series Thresholding Configuration Guide OL-25552-02...
Page 163: Saving Your Configuration
Exec mode command . For additional information on how to verify and save save configuration configuration files, refer to the System Administration Guide and the Command Line Interface Reference. Cisco ASR 5000 Series Thresholding Configuration Guide ▄ OL-25552-02...

Cisco ASR 5000 Series Thresholding Configuration Manual

About this Guide

Thresholding Overview

AAA Thresholds

ASN GW Service Thresholds

Call Setup Thresholds

Content Filtering Thresholds

CPU Resource Thresholds

CSCF Service Thresholds

Diameter Thresholds

FA Service Thresholds

FNG Thresholds

HA Service Thresholds

IP Pool Utilization Thresholds

MME Service Thresholds

Network Address Translation Thresholds

Packet Processing Thresholds

PDG/TTG Thresholds

PDIF Thresholds

PDSN Service Thresholds

Per-Service Session Thresholds

Port Utilization Thresholds

Session License Utilization Thresholds

Stateful Firewall Thresholds

Subscriber Thresholds

System Management Card Compactflash Memory Thresholds

Total Session Thresholds

Traffic Performance Optimizer Thresholds

Quick Links

Related Manuals for Cisco ASR 5000 Series

Summary of Contents for Cisco ASR 5000 Series