∗ ∗ ∗ ∗ 29 Menu Mode For Ip And Gsm Module Programming - Honeywell ADEMCO VISTA SERIES VISTA-21iP Installation And Setup Manual

∗ ∗ ∗ ∗ 29 Menu Mode for IP and GSM Module Programming
This mode is for programming the Internet connection (IP) and optional VISTA-GSM4G Module
configuration, collectively referred to as the Internal Device.
NOTE: The Internal Device is automatically set to address 3 and cannot be changed.
The following section describes the programming of the Internal Device using an alpha keypad.
Alternatively, these options can be programmed via the AlarmNet Direct website. After programming is
complete, the control must be registered with AlarmNet via the Internet connection. Refer to the
Registration with AlarmNet section for procedures.
IMPORTANT: The use of the IP connection or the VISTA-GSM4G module requires an AlarmNet–I
account. Please obtain the account information from the central station prior to programming this
module.
Using an Alpha Keypad as a 7720P Programming Tool
When programming IP/GSM features (with ∗29
menu mode), the alpha keypad mimics the
functions of the 7720P Programming Tool. See
figure at right and table below for 7720P key
functions. Each key has two possible functions: a
normal function and a SHIFT function.
Normal functions: The numeric values labeled
directly on the keys and the left-hand functions
shown in diagram on the ABC keys. To perform a
normal key function, simply press the desired key.
SHIFT functions: Those functions shown in
diagram above the numerical keys and the right-
hand functions shown on the ABC keys. To
perform a SHIFT key function, press SHIFT key
(D key), then press the desired function key (shift
function is indicated by the lit READY LED).
Normal and SHIFT key Functions While in ∗ ∗ ∗ ∗ 29 Menu Mode
Key Normal Key Function
(A) = BS/ESC [BS]: Press to delete entry
Also, can reset EEPROM defaults
(B) = ↓/↑
[↓]: Scroll down programming
(C) = N/Y [N]: Press for "NO" answer
(D) = SHIFT Press before pressing a SHIFT key function. Will light READY LED. LED goes out once a key is pressed. Press again
for each SHIFT function desired.
1/A [1]: For entering the number 1
2/B [2]: For entering the number 2
3/C [3]: For entering the number 3
4/D [4]: For entering the number 4
5/E [5]: For entering the number 5
6/F [6]: For entering the number 6
7/S [7]: For entering the number 7
8/T [8]: For entering the number 8
9/X [9]: For entering the number 9
[∗] / SPACE [∗]: Used to select programming options
0 [0]: For entering the number 0
[#] / ENTER [#] / ENTER: Press to accept entries
† Active only when the "REVIEW?" prompt is displayed
SHIFT
FUNCTION
WHEN LIT
SHIFT Key Function
[ESC]: Press to quit Program Mode
†
[↑]: Scroll up programming
[Y]: Press SHIFT-Y for "YES" answer
[A]: Used for entering C.S. ID number
[B]: Used for entering C.S. ID number
[C]: Used for entering C.S. ID number
[D]: Used for entering C.S. ID number
[E]: Used for entering C.S. ID number
[F]: Used for entering C.S. ID number
[S]: Press to display diagnostic status
[T]: Press to send TEST messages
[X]: Press to reset the IP/GSM
[SPACE]: Not used
No SHIFT function
Menu Mode Programming
(A)
1
ARMED
BS/ESC
(B)
4
/
READY
(C)
7
N / Y
SPACE
(D)
SHIFT
7720P Emulation Template for Alpha Keypads
A B C
2 3
OFF AWAY STAY
D E F
5 6
MAX TEST BYPASS
T X
S
8 9
INSTANT CODE CHIME
ENTER
0 #
READY
6160-7720P-001-V0
5-19