Honeywell ADEMCO VISTA SERIES VISTA-21iP Installation And Setup Manual page 67

IP/GSM Diagnostic Commands (continued)
[E]
PriRSSI 3/4G REG
-xxxdbm stat x
or
PriRSSI 2G REG
-xxxdbm stat x
2G Network Stat can be :
Good –20 to –89 dBm
OK –90 to –98 dBm
Marg. –99 to –104 dBm
Bad –105 to –150
dBm
RAT EC/NO
3/4G -xxxxx
Cntry Netw LAC
xxx xxx xxxxx
Cell BaseSt Chan
Xxxxx x xxx
Second Site RSSI
-xxxdbm
[F]
Testing Gateway
Redir 1
GSM Status Displays
Only if GSM or IP/GSM
enabled.
PriRSSI – Primary Site
RSSI level in dbm
3/4G – Communicator is on
the 3G/4G network where
"stat" can be:
Good RSSI –20 to –90 dBm
OK RSSI –91 to –99 dBm
Marginal RSSI –100 to –105 dBm
Bad RSSI –106 to –150 dBm
REG – Registration status
from GSM module where
"x" can be:
N – Not Registered
H – Registered Home
S – Searching
D – Registration Denied
R – Registered Roaming
? – Unknown Reg. State
[∗] to continue to next
screen.
RAT = Radio Access
Technology
EC/NO = Carrier Noise
Ratio
(EC/NO does not
apply to 2G network ;
displays N/A)
[∗] to continue to next
screen.
Cntry – Country Code
Netw – Network Code
LAC – Reg. status from
GSM.
[∗] to continue to next
screen.
Cell – Base Station ID
BaseSt – Base Station
Antenna Sector
Chan – Control Channel
in use
[∗] to continue to next
screen.
Secondary GSM Site RSSI
level in dbm.
[∗] to continue to next
screen.
Network Diagnostic
Test
Only if IP or IP/GSM
enabled.
Performs a set of network
diagnostics that tests the
integrity of the links
between the IP/GSM and
the various connection
points (Redirs) to
AlarmNet.
Key Prompt
[S]
FLT
OK
[T]
Test Msg Sent
[X]
Reset CPU Y/N
[↑ ↑ ↑ ↑ ]
Registering ...
[↓ ↓ ↓ ↓ ]
Enter PIN#
[0]
Force Server Update
Y/N
Menu Mode Programming
Function
Status request
OK = normal
i = IP off line
I = IP fault reported
g = GSM off line
G = GSM fault reported
Test Alarm
Sends a Test alarm to
AlarmNet. Functional for a
registered IP/GSM only. If
the device is not
registered, a message is
displayed indicating that
the command cannot be
executed.
Reset the IP/GSM.
[N] = return to diagnostic
mode (blank screen =
enter next command
or escape).
[Y] = resets the module
(blank screen = when
reset complete, enter
next command or
escape).
Registration
(Shift-UP arrow)
Registers a programmed
IP/GSM with AlarmNet. If
it is configured to report to
AlarmNet, the IP/GSM will
register with AlarmNet.
Registration with PIN
for Replacement
Module (DN arrow)
Registers a programmed
IP/GSM with AlarmNet if
it is configured to report to
AlarmNet.
Force Upload of
Configuration File to
Server
[Y] = force the device to
upload its entire
configuration file to the
server.
[N] = cancel the operation.
NOTE: If the internet is
not available, and the
module is not initialized
when you enter this
command, the following
screen will be displayed:
Cannot Upload
Try Later! _
Wait for the RSSI LEDs to
light, indicating the
module has completed its
initialization, and try
again.
5-25