Makita DCU603 Instruction Manual page 24

Installing or removing the dump unit
Optional accessory
Installing the dump unit
1.
Take out the dump unit and the handle from the box.
► Fig.8: 1. Dump unit 2. Handle
2. Insert the pipes of the handle into the dump unit as
shown in the figure, and then tighten 4 bolts securely.
► Fig.9: 1. Bolt 2. Handle
NOTE: When tightening the bolts, lift the handle
slightly.
3. Make sure that the dump unit is locked by pulling
down the handle.
► Fig.10: 1. Handle
4. Remove the cord cover located in the lower right
corner on the rear of the machine.
► Fig.11: 1. Cord cover
5. Place the dump unit on the base unit by holding
the dump unit with two people as shown in the figure.
► Fig.12
6. Temporarily tighten 2 bolts at the rear of the
machine. Tighten the rest of 4 bolts securely, and then
tighten 2 bolts at the rear of the machine securely.
► Fig.13: 1. Bolt (front) 2. Bolt (rear)
7. Attach the cord cover.
► Fig.14: 1. Cord cover
Removing the dump unit
To remove the dump unit, perform the installation proce-
dure in reverse.
Installing or removing the bucket
Optional accessory
Installing the bucket
1.
Take out the bucket, stays, and front pipe from the box.
► Fig.15: 1. Bucket 2. Stay 3. Front pipe
2. Insert the front pipe between the upper frame and
lower frame of the dump unit.
► Fig.16: 1. Front pipe
3. Place the stay on the dump unit, and then tempo-
rarily tighten the bolts with the front pipe together. Install
the other stay to the dump unit in the same way.
► Fig.17: 1. Stay 2. Bolt
4. Place the bucket on the front pipe and left and right stays.
Place the rubber washer on the hole of the bucket and
insert the bolt from the top. Attach the flat washer and
spring washer in order to the bolt, and then tighten the
nut from the bottom. Tighten the rest of the bolts and
nuts in the same way.
► Fig.18: 1. Bolt 2. Rubber washer 3. Flat washer
4. Spring washer 5. Nut
5. Securely tighten 4 bolts which were temporarily
tightened in step 3.
Removing the bucket
To remove the bucket, perform the installation proce-
dure in reverse.
Installing or removing the carrier
Optional accessory
Installing the carrier
1. Take out the carrier from the box, and attach the
side rails and front rail to the base frame.
► Fig.19
2. Tighten 6 thumb nuts together with springs and
washers to fix the rails.
► Fig.20: 1. Thumb nut 2. Spring 3. Washer
3. Place the carrier on the dump unit.
Insert the bolt from the top. Attach the flat washer and
spring washer in order to the bolt, and then tighten the
nut from the bottom. Tighten the rest of the bolts and
nuts in the same way.
► Fig.21: 1. Bolt 2. Flat washer 3. Spring washer
4. Nut
Removing the carrier
To remove the carrier, perform the installation proce-
dure in reverse.
Installing or removing the flat
bucket
Optional accessory
Installing the flat bucket
1. Take out the flat bucket and holding frames from
the box.
► Fig.22: 1. Flat bucket 2. Holding frame
2. Assemble the holding frames by tightening 12
bolts.
► Fig.23: 1. Bolt
3. Remove the cord cover located in the lower right
corner on the rear of the machine.
► Fig.24: 1. Cord cover
4. Place the holding frames on the base unit, and
then temporarily tighten 2 bolts at the rear of the
machine. Tighten the rest of 4 bolts securely, and then
tighten 2 bolts at the rear of the machine securely.
► Fig.25: 1. Bolt (front) 2. Bolt (rear)
5.
Attach the cord cover.
► Fig.26: 1. Cord cover
6. Hold the long sides of the flat bucket with two
people as shown in the figure, and mount the flat bucket
to the holding frames.
► Fig.27
Removing the flat bucket
To remove the flat bucket, perform the installation pro-
cedure in reverse.
24 ENGLISH