Makita DVC860L Instruction Manual page 12

Installing the paper pack (optional
accessory)
WARNING:
• When using the paper pack, also use the cloth
filter or prefilter together that is preinstalled on
the tool. Failure to use the cloth filter / prefilter
together may cause unusual noise and heat,
resulting in a fire.
CAUTION:
(For the cloth filter model)
• Never pick up water or other liquids or wet dusts
when using the paper pack. Picking up such
things may cause the paper pack breakage.
• Before using the paper pack, make sure that
powder filter (optional accessory), damper
(optional accessory) and prefilter are always
used together.
(For the powder filter model)
• Before using the paper pack, make sure that
powder filter, damper and prefilter are always
used together.
1. Remove the rubber holder.
► Fig.16: 1. Rubber holder
2. Extend the paper pack.
3. Align the paper pack opening with the dust suction
opening of the cleaner.
4. Insert the cardboard of the paper pack onto the
holder so that it is positioned at the end beyond
the detent protrusion.
► Fig.17: 1. Paper pack 2. Holder
Installing the polyethylene bag
Cleaner can also be used without polyethylene bag.
However, using polyethylene bag is easier to empty the
tank without letting your hands dirty.
► Fig.18: 1. Holder plate 2. Polyethylene bag
Spread the polyethylene bag in the tank. Insert it
between the holder plate and the tank, and pull it to the
hose inlet.
Spread the bag around the top of the tank so that the
prefilter edge can catch and hold the bag securely.
NOTE:
• A polyethylene bag available on the mar-
ket can be used. 0.04 mm or thicker one is
recommended.
• Too much dust will tear the bag easily, so do not
collect the dust more than the half of the bag
capacity.
Emptying the polyethylene bag
WARNING:
• Always make sure that the cleaner is switched
off and unplugged before emptying the polyeth-
ylene bag. Failure to do so may cause an elec-
tric shock and serious personal injury.
CAUTION:
• Do not apply a great impact on the float cage
and tank. Applying a great impact may cause
deformation and damage to the parts.
• Empty the tank at least once a day although this
depends on picked-up dust volume in the tank.
Or, the suction force will weaken and the motor
may be broken.
• Do not grab the hook when emptying the tank.
Grabbing the hook may cause the hook to
break.
Unhook and lift up the tank cover.
► Fig.19
Shake off the dust from the cloth filter / powder filter and
then take the polyethylene bag out of the tank.
NOTE:
• Take the polyethylene bag carefully out of the
tank so that the polyethylene bag cannot be
caught and torn by the protrusion inside the tank
when emptying it.
• Empty the polyethylene bag before it becomes
full. Too much dust in the tank may cause the
polyethylene bag to be torn.
Installing the tool box
► Fig.20
1. Release the lock of the battery cover, and open
the battery cover.
2. Set the rails on the tool box along the grooves on
the housing.
3. Close the battery cover and apply the lock.
► Fig.21
The tool box is convenient for carrying batteries, exten-
sion code, pipe, or cuffs.
Connecting the hose
CAUTION:
• Never force the hose for bending or stamp it.
Never move the cleaner by a hose. Forcing,
stamping and pulling the hose may cause a
breakage or deformation of the hose.
• When picking up large wastes such as planer
carvings, concrete dusts or similar other than
small wastes, use the 38 mm inner diameter
hose (optional accessory). Using the 28 mm
inner diameter hose (optional accessory) may
cause a hose stuffing and damage.
► Fig.22
Insert the hose onto the mounting port of the tank and
turn it clockwise until it locks.
12 ENGLISH