Cisco MDS 9000 series Configuration Manual page 62

IOA Flow Setup Wizard
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
This step is only for those switches where none of the hosts or targets have been configured yet for
acceleration. From the flows in the active zone set, a candidate switch list is prepared based on where
the hosts and targets are logged into.
The following switches need to be classified into appropriate sites
-------------------------------------------------------------------------------
Do you want to classify sjc-sw1 into site sjc or rtp [sjc]
Do you want to classify 172.23.144.96 into site sjc or rtp [sjc] rtp
The candidate flow list is now pruned to contain only the inter-site flows that need to be accelerated.
The wizard displays all of the N ports that need to be classified into sites. Enter yes to classify the N
Step 3
ports into sites.
The following nport to site mapping needs to be configured
-------------------------------------------------------------------------------
N-Port PWWN: 10:00:00:00:00:00:00:00 Site: sjc
N-Port PWWN: 10:00:00:00:00:00:01:00 Site: sjc
N-Port PWWN: 10:00:00:00:00:00:02:00 Site: sjc
N-Port PWWN: 10:00:00:00:00:00:03:00 Site: sjc
N-Port PWWN: 10:00:00:00:00:00:04:00 Site: sjc
N-Port PWWN: 11:00:00:00:00:00:00:00 Site: rtp
N-Port PWWN: 11:00:00:00:00:00:01:00 Site: rtp
N-Port PWWN: 11:00:00:00:00:00:02:00 Site: rtp
N-Port PWWN: 11:00:00:00:00:00:03:00 Site: rtp
N-Port PWWN: 11:00:00:00:00:00:04:00 Site: rtp
Do you want to configure the n-port to site mappings? (yes/no) [yes] yes
(Optional) Use this step only when some of the N ports such as those used in remote replication are
Step 4
represented as scsi-fcp(both) in the FCNS database. Enter the primary direction of the traffic that will
be used by IOA to decide on what should be configured as host and target in IOA.
Replication traffic can flow in either direction.
Certain N-ports in this VSAN can act as both initiator and targets
Is the traffic flow primarily from sjc to rtp? (yes/no) [yes] yes
The wizard configures the list of flows that are not already configured in IOA and attempts to delete the
Step 5
IOA flows that are not part of the zone set. This operation specifically handles removing HBAs or storage
controllers. Enter yes to accept the flows that need to be accelerated. New flows that need to be
accelerated are displayed.
The following flows will be configured
-------------------------------------------------------------------------------
Host: 10:00:00:00:00:00:00:00 VSAN: 100 Target: 11:00:00:00:00:00:00:00 VSAN:100
Host: 10:00:00:00:00:00:00:00 VSAN: 100 Target: 11:00:00:00:00:00:01:00 VSAN:100
Host: 10:00:00:00:00:00:00:00 VSAN: 100 Target: 11:00:00:00:00:00:02:00 VSAN:100
Host: 10:00:00:00:00:00:00:00 VSAN: 100 Target: 11:00:00:00:00:00:03:00 VSAN:100
Host: 10:00:00:00:00:00:01:00 VSAN: 100 Target: 11:00:00:00:00:00:00:00 VSAN:100
Host: 10:00:00:00:00:00:01:00 VSAN: 100 Target: 11:00:00:00:00:00:01:00 VSAN:100
Host: 10:00:00:00:00:00:01:00 VSAN: 100 Target: 11:00:00:00:00:00:02:00 VSAN:100
Host: 10:00:00:00:00:00:01:00 VSAN: 100 Target: 11:00:00:00:00:00:03:00 VSAN:100
Host: 10:00:00:00:00:00:02:00 VSAN: 100 Target: 11:00:00:00:00:00:00:00 VSAN:100
Host: 10:00:00:00:00:00:02:00 VSAN: 100 Target: 11:00:00:00:00:00:01:00 VSAN:100
Host: 10:00:00:00:00:00:02:00 VSAN: 100 Target: 11:00:00:00:00:00:02:00 VSAN:100
Host: 10:00:00:00:00:00:02:00 VSAN: 100 Target: 11:00:00:00:00:00:03:00 VSAN:100
Host: 10:00:00:00:00:00:03:00 VSAN: 100 Target: 11:00:00:00:00:00:00:00 VSAN:100
Host: 10:00:00:00:00:00:03:00 VSAN: 100 Target: 11:00:00:00:00:00:01:00 VSAN:100
Host: 10:00:00:00:00:00:03:00 VSAN: 100 Target: 11:00:00:00:00:00:02:00 VSAN:100
Host: 10:00:00:00:00:00:03:00 VSAN: 100 Target: 11:00:00:00:00:00:03:00 VSAN:100
Host: 10:00:00:00:00:00:04:00 VSAN: 100 Target: 11:00:00:00:00:00:04:00 VSAN:100
Do you want to configure these flows? (yes/no) [yes] yes
Cisco MDS 9000 Family I/O Accelerator Configuration Guide
4-12
Chapter 4 Configuring IOA Using the CLI
OL-20708-01, Cisco MDS NX-OS Release 5.0(1a)