Yamaha RX-V4600 Owner's Manual page 75

3
Press and hold LEARN for about 3 seconds
using a ballpoint pen or similar object.
The library name (ex. "L;DVD") and the selected
component name (ex. "DVD") appear alternately in
the display window.
LEARN
y
If you want to setup for another component, press the input
selector button or SELECT k / n to select the component.
Notes
• Be sure to press and hold LEARN for at least 3 seconds,
otherwise the learning process will start.
• If you do not complete each of the following steps within
30 seconds, the setting mode will be automatically
canceled. In this case, press LEARN again.
If you want to change a library (component
category), press l / h. You can set a
different type of component.
Library choices: L;DVD, L;DVR, L;LD, L;CD,
L;CDR, L;MD, L;TAP (tape), L;TUN (tuner),
L;AMP * , L;TV, L;CAB (cable), L;SAT (satellite),
L;VCR
* The amplifier library (L;AMP) code is preset to "2000" in
order to operate this unit. However, you can switch by
entering one of the following 4 codes if necessary.
Setting remote control AMP codes
Select one of the following codes to set the remote control
AMP code for the component you want to use.
Set AMP/SOURCE/TV to AMP or SOURCE, then
change the remote control code settings.
AMP library
code
Function
(remote
control
setting)
2000 To operate this unit using
(initial setting) the default code.
To operate this unit using
the default code.
2001
To operate Zone 2 or Zone 3
features (see page 83).
To operate this unit using an
2002
alternative code.
To operate this unit using an
alternative code.
To operate Zone 2 or Zone 3
2003
features of other YAMAHA
receivers/amplifiers
(see page 83).
Setting remote control tuner codes
Select one of the following codes to set the remote control
tuner code for the component you want to use.
Set AMP/SOURCE/TV to SOURCE and the unit to the
tuner mode by pressing TUNER on the remote control,
then change the remote control code settings.
Tuner
library code
(remote
control
setting)
2602
(initial setting)
2603
Note
When using multiple YAMAHA receivers/amplifiers, you
may be able to operate the other components simultaneously
with the default code setting. In this case, set one of the
alternative codes to operate this unit separately.
4
Press ENTER.
The four-digit code set for the selected component
appears in the display window.
Note
"0000" appears in the display window if no code has been
set.
5
Press the numeric buttons to enter the
four-digit remote control code for the
component you want to use.
For a complete list of available remote control codes,
refer to "LIST OF REMOTE CONTROL CODES" at
the end of this manual.
Remote
control
AMP ID
(this unit's
setting:
see page 87)
6
Press ENTER to set the number.
"OK" appears in the display window if setting was
ID1
successful.
(initial setting)
"NG" appears in the display window if the setting
was unsuccessful. In this case, start over from step 3.
y
If you continuously want to set up another code for another
component, press the input selector button or
SELECT k / n to select the component, then repeat steps 4
ID2
through 6.
REMOTE CONTROL FEATURES
Function
To operate this unit using
the default code.
To operate this unit using an
alternative code.
STEREO MUSIC ENTERTAIN MOVIE
1 2 3 4
THX
STANDARD SELECT EXTD SUR.
5 6 7 8
1 MEMORY 2 A SPEAKERS B
9 0 +10
ENT.
Remote
control
tuner ID
(this unit's
setting:
see page 87)
ID1
(initial setting)
ID2
73