Display Machine Data For Shopmill - Siemens SINUMERIK 840DE sl Commissioning Manual

7 Machine Data
7.2

Display machine data for ShopMill

7.2 Display machine data for ShopMill
7.2.1 Overview of machine data display
MD MD identifier
num-
ber
9014 $MM_USE_CHANNEL_DISPLA Y_DATA
9020 $MM_TECHNOLOGY
9422 $MM_MA_PRESET_MODE
9426 $MM_MA_AX_DRIVELOAD_FROM_PLC1
9427 $MM_MA_AX_DRIVELOAD_FROM_PLC2
9428 $MM_MA_SPIND_MAX_POWER
9429 $MM_MA_SPIND_POWER_RANGE
9450 $MM_WRITE_TOA_FINE_LIMIT
9451 $MM_WRITE_ZOA_FINE_LIMIT
9460 $MM_PROGRAM_SETTINGS
9478* $MM_TO_OPTION_MASK
9479* $MM_TO_MAG_PLACE_DIST ANCE
9480 $MM_MA_SIMULA TION_MODE
9481 $MM_MA_ST AND_SIMULATION_LIMIT
9602 $MM_CTM_SIMULA TION_DEF_VIS_AREA
9603 $MM_CTM_SIMULA TION_MAX_X
9604 $MM_CTM_SIMULA TION_MAX_Y
9605 $MM_CTM_SIMULA TION_MAX_VIS_AREA
9626 $MM_CTM_TRACE
9639 $MM_CTM_MAX_T OOL_WEAR
9640 $MM_CTM_ENABLE_CALC_THREAD_PITCH
9646 $MM_CTM_F ACTOR_O_CALC_THR_PITCH
9647 $MM_CTM_F ACTOR_I_CALC_THR_PITCH
9650* $MM_CMM_POS_COORDINA TE_SYSTEM
9651* $MM_CMM_TOOL_MANAGEMENT
9652* $MM_CMM_TOOL_LIFE_CONTROL
9653* $MM_CMM_ENABLE_A_AXIS
9654 $MM_CMM_SPEED_FIELD_DISPLA Y_RES
9655 $MM_CMM_CYC_PECKING_DIST
9656 $MM_CMM_CYC_DRILL_RELEASE_DIST
9657 $MM_CMM_CYC_MIN_CONT_PO_T O_RAD
7-42
After the installation of ShopMill on the PCU and the startup of NCK and PLC
are completed, you still need to adapt the display machine data.
In any case, you must check the settings of the display machine data that are
identified in table 7-1 with "*".
Table 7-1 Display machine data for ShopMill
SINUMERIK 840D sl Commissioning Manual CNC: ShopMill – 11/2006 Edition
Comment
Use channel–specific display machine
data
Basic configuration turning/milling
Preset/basic offset in JOG
Machine index of an analog spindle for the
drive load display
Machine index of an analog spindle for the
drive load display
Factor for display of spindle utilization
Display area for spindle utilization
Limit value for wear fine
Limit value for fine adjustment
Settings in the Program area
Settings for ShopMill
Distance between individual tool holders
Switch fast view on/off
Limit of the standard simulation in KB
Simulation of default display area
Simulation of maximum display X
Simulation of maximum display Y
Simulation of maximum display area
Settings in ShopMill
Upper input limit for tool wear
Calculation of thread depth if pitch entered
Factor for calculating the external thread
depth if pitch entered
Factor for calculating the internal thread
depth if pitch entered
Position of coordinate system
Tool management variant
Tool monitoring
Enable 4th axis for operator interface
Number of decimal places in the speed
input field
Retraction distance for deep hole drilling
Retraction distance for boring
Variation of smallest possible cutter radius
in percent
© Siemens AG 2006 All Rights Reserved
11/2006
Preset
default
0
2
1
0
0
100
200
0.999
0.999
H8
1
0
–1
200
100
0
0
1000
0
1
0
0,6134
0,5413
0
4
1
0
0
–1
–1
5