Table of Contents
Advertisement
Understanding the InfoCenter Menu Items
To access the main menu, press any button while at
the main, CU motor, or traction information screen,
then press the button that corresponds with the
symbol. This brings you to the M
Refer to the following tables for a description of the
options available from the menus:
Main Menu
Menu Item
F
AULTS
S
ERVICE
D
IAGNOSTICS
S
ETTINGS
A
BOUT
Faults
Menu Item
C
URRENT
L
AST
F
IRST
O
CCURRENCES
M
.
AIN
ENU
Description
The F
menu contains
AULTS
a list of the recent machine
faults. Refer to the Service
Manual or your authorized
Toro distributor for more
information on the F
AULTS
menu.
The S
menu contains
ERVICE
information on the machine
such as hours of use, counts,
and calibration. You can
also enable the cutting-unit
backlap procedure. Refer to
the
Service (page 21)
table.
The D
menu lists
IAGNOSTICS
various states and data that
the machine currently has.
You can use this information
to troubleshoot certain issues,
as it quickly tells you which
machine controls are on/off
and lists control levels (e.g.,
sensor values).
The S
menu allows
ETTINGS
you to customize and modify
configuration variables on the
InfoCenter display. Refer to
the
Settings (page 21)
table.
The A
menu lists the
BOUT
model number, serial number,
and software version of your
machine. Refer to the
About
(page 22)
table.
Description
Lists the total number of
key-on hours (i.e., hours that
the key has been in the O
N
position).
Indicates the last key-on hour
that the fault occurred on.
Indicates the first key-on hour
that the fault occurred on.
Indicates the number of fault
occurrences.
Service
Menu Item
H
OURS
C
OUNTS
B
ACKLAP
C
ALIBRATION
Settings
Menu Item
U
NITS
L
ANGUAGE
B
ACKLIGHT
C
ONTRAST
P
M
ROTECTED
ENUS
P
S
ROTECT
ETTINGS
R
D
ESET
EFAULTS
T
T
APOFF
IME
R
S
EEL
PEED
L
S
OWER
PEED
B
ACKLAP RPM
C
C
LIP
ONTROL
B
C
LADE
OUNT
H
C
(HOC)
EIGHT OF
UT
21
Description
Lists the total number of
hours that the key, reels, and
backlap have been on.
Lists the number of mows,
tap-offs, and backlaps.
Engages/disengages the
cutting-unit backlap procedure
(when you engage this
procedure, you can disengage
the mode with this setting or
by moving the key to the O
position).
Allows you to calibrate the
steering system, traction
system, and lift actuators.
Refer to the Service Manual
for more information on
calibration.
Description
Controls the units used on the
InfoCenter. The menu choices
are English or metric.
Controls the language used
on the InfoCenter.
Controls the brightness of the
LCD display.
Controls the contrast of the
LCD display.
Allows you to access
protected menus by inputting
a passcode.
Controls the protected menus.
Resets the InfoCenter to
default settings.
Controls the tap-off delay.
Controls the reel speed.
Sets the speed that the cutting
units lower to the ground for
mowing.
Controls the backlap rpm
speed.
Turns the automatic
clip-control feature O
/O
N
FF
Set the number of blades in
each reel. This setting is only
necessary if C
C
LIP
ONTROL
set to O
.
N
Sets the desired height of cut.
This setting is only necessary
if C
C
is set to O
LIP
ONTROL
N
FF
.
is
.
Advertisement
Table of Contents
