Starting The Engine; Checking The Machine After Starting The Engine - Toro Greensmaster 3150 Operator's Manual

Since the first hours of operation are critical to future
dependability of the machine, monitor its functions and
performance closely so that minor difficulties, which
could lead to major problems, are noted and can be
corrected. Inspect the machine frequently during
break-in for signs of oil leakage, loose fasteners, or
any other malfunction.

Starting the Engine

Note:
Inspect the area beneath the mowers to be
certain they are clear of debris.
1. Sit on the seat, ensure that the parking brake
is engaged, disengage the raise/lower mow
control, and move the functional control lever to
the N position.
EUTRAL
2. Ensure that your foot is not on the traction pedal
and make sure the pedal is in the N
position.
3. Move the choke lever to the O
when starting a cold engine) and the throttle
lever to the H
ALF
4. Start the engine and regulate the choke to keep
it running smoothly.
5. As soon as possible, open the choke by pulling
it rearward to the O
Note:
A warm engine requires little or no
choking.
6. Check the machine out with the following
procedures after the engine has started:
A. Move the throttle lever to the F
B. Move the traction-control lever to the M
position and momentarily engage the reels
by moving the raise/lower mow-control lever
forward.
The cutting units should drop and all the
reels should rotate.
C. Move the raise/lower mow control lever
rearward until the cutting units raise to the
full transport position.
The cutting units stop rotating as soon as
they start to lift. If you release the lever
before the cutting units are fully raised, the
upward motion stops, but the cutting units
still stop rotating.
D. Lock the parking brake and shut off the
engine.
E. Check the lip of each basket to ensure it is
not in contact with the reel during operation.
If you see signs of contact, adjust the pull
arms; refer to
(page 11).
EUTRAL
position (only
N
T position.
HROTTLE
position.
FF
position.
AST
4 Installing the Cutting Units
F. Check for oil leaks and tighten the hydraulic
fittings if any are found.
Note:
bearings and reels are tight, it is necessary
to use the F
this check. A fast throttle setting may not be
required after the break-in period.
Note:
contact your authorized Toro distributor for
assistance and, if necessary, replacement
parts.
Important:
or wheel seals is normal. Seals require
a small amount of lubrication to perform
properly.
Checking the Machine After
Starting the Engine
1. Move the throttle lever to the F
2. Move the raise/lower mow control lever forward
momentarily.
The cutting units should lower and all the reels
should rotate.
Note:
The function lever should be in the
middle (mow) position for the reels to run when
lowering the cutting units
3. Move the raise/lower mow control lever
rearward.
The cutting reels should stop rotating and the
cutting units should raise to the full transport
position.
OW
4. Engage the brake to keep the machine from
moving, and operate the traction pedal through
the forward and reverse positions.
5. Continue the above procedure for 1 to 2 minutes.
Move the functional-control lever to the N
position, lock the parking brake, and shut off the
engine.
6. Check for fluid leaks and tighten the hydraulic
fittings if any leaks are found.
Note:
When the machine is new and the
bearings and reels are tight, it is necessary
to use the F
check. A fast throttle setting may not be required
after the break-in period.
Note:
If fluid leaks continue to appear, contact
your authorized Toro distributor for assistance
and, if necessary, replacement parts.
Important:
wheel seals is normal. Seals require a small
amount of lubrication to perform properly.
21
When the machine is new and the
throttle lever position for
AST
If oil leaks continue to appear,
A trace of oil on the motor
AST
throttle lever position for this
AST
A trace of fluid on the motor or
position.
EUTRAL