Canon imagePRESS Server G200 Service Manual page 50

9. Attach the prepared USB flash drive to one of the USB connectors on the imagePRESS Server
connector panel and LED diagnostic codes" on page
NOTE:
If dust covers are attached to the USB connectors, remove one dust cover using needlenose pliers.
10. Power on the imagePRESS Server by pressing the power switch to set ON (|), and then power on the printer using the main
power switch on the front.
Make sure that the imagePRESS Server turns on.
11. Check the LED display for the file transfer activity. After confirming the LED activity starts and the LED display shows the
cyclic codes (C1 > C2 > C3 > C1...), turn off the printer using the main power switch on the front.
12. Wait while the files are transferred.
The file transfer can take from 5 to 15 minutes depending on the USB flash drive.
The LED on the flash drive shows sporadic activity during this time. After the imagePRESS Server LED display shows the
cyclic codes (C1 > C2 > C3 > C1...), it eventually settles on 00. When all of the files have been transferred, the imagePRESS
Server automatically shuts down.
13. Remove the USB flash drive from the imagePRESS Server.
14. Flip the service switches to normal mode (both switches set to OFF).
For an illustration of the service switch modes, see above figure.
IMPORTANT:
If you do not remove the USB flash drive (step 13) and do not flip the service switches to normal mode (step 14), when the
imagePRESS Server is starting up, it will try to copy the files again from the USB, and cause the imagePRESS Server start
up to fail.
15. Reconnect the cables to the imagePRESS Server
on page 11):
• Connect the network cable between the imagePRESS Server and the customer network.
• Connect the crossover Ethernet cable between the imagePRESS Server and the printer.
NOTE:
Be sure to use the correct cable for each connection.
16. Make sure that the imagePRESS Server power switch is in the ON (|) position.
17. Power on the printer using the main power switch.
Allow the imagePRESS Server to start up and reach Idle (00 should appear on the imagePRESS Server LED display).
NOTE:
If you press the Fiery icon on the printer touch panel before the imagePRESS Server finishes the startup process, "TCP connect
error" appears on the printer touch panel. Press OK to return to the main menu, and wait until the imagePRESS Server reaches
Idle. Wait approximately 15 minutes longer for the imagePRESS Server to start up and print Start page.
18. If you saved a configuration file earlier, restore the system configuration (see
40).
NOTE:
If it was not possible to save a configuration file or if you installed an upgraded version of system software, you must configure
Setup using the Configuration pages you printed earlier. For information about performing Setup, see Configuration and Setup,
which is part of the user documentation set. Bypass any settings if it is more appropriate for the site administrator to set them.
After you exit Setup and allow the system to reboot, ask the site administrator to restore the custom files that were archived earlier.
19. Install any required software patches:
• If you reinstalled the same version of system software, be sure to reinstall all software patches that were previously
installed on the imagePRESS Server. For a list of installed patches, see the Configuration pages that you printed earlier.
• If you installed an upgraded version of system software (for example, version 1.0 to version 2.0), contact your authorized
service/support center for a list of valid software patches. Some or all of the patches listed on the Configuration pages
that you printed earlier may no longer be valid. Before installing a patch, be sure to verify with your authorized service/
support center that it is valid for your system version. Installing an invalid patch may result in system corruption.
20. Reconnect any USB devices that you may have removed earlier.
11) .
(see"imagePRESS Server connector panel and LED diagnostic codes"
"To restore the system configuration" on page
45
4. INSTALLING SYSTEM SOFTWARE
(see"imagePRESS Server