ABB PSTX30 Installation And Commissioning Manual page 89

Fieldbus Inputs/Outputs
Functions set in the softstarter as Fieldbus digital inputs
(DI) are in fact the digital inputs to the PLC i.e. the data
flow from the softstarter through the network to the PLC.
Fieldbus digital outputs (DO) are not configurable. The
output (DO) describes data flow from the network to the
softstarter i.e. appears as an input, from the softstarter
point of view.
Fieldbus communication is configured with the
following parameters:
Parameter
12.01 Com3 function
12.02 FB interface connector
12.03 Fieldbus control
12.04 Fieldbus address
12.05 Fieldbus ip address
12.06 Fieldbus ip gateway
12.07 Fieldbus ip netmask
12.08 Fieldbus ip dhcp client
12.09 FB baud rate*
12.10 FB parity
12.11 FB stop bits
12.12 Fieldbus DI 1
12.13 Fieldbus DI 2
12.14 Fieldbus DI 3
12.15 Fieldbus DI 4
12.16 Fieldbus DI 5
12.17 Fieldbus DI 6
12.18 Fieldbus DI 7
12.19 Fieldbus DI 8
12.20 Fieldbus DI 9
12.21 Fieldbus DI 10
Phone: 800.894.0412 - Fax: 888.723.4773 - Web: www.clrwtr.com - Email: info@clrwtr.com
Description
Sets the function of the Com3
port.
Sets the Fieldbus interface
selection.
Enables control from fieldbus.
Sets the Bus address.
Fieldbus IP: Sets the IP-
address.
Fieldbus IP: Sets the default
gateway.
Fieldbus IP: Sets the netmask.
Fieldbus IP: Enables dhcp.
Sets the baud rate of internal
Modbus-RTU interface,
Anybus DeviceNet and Anybus
Modbus-RTU.
Sets parity for Anybus Modbus-
RTU.
Select stop bits for Anybus
Modbus-RTU.
Sets the DI 1 programmable
digital input signal.
Sets the DI 2 programmable
digital input signal.
Sets the DI 3 programmable
digital input signal.
Sets the DI 4 programmable
digital input signal.
Sets the DI 5 programmable
digital input signal.
Sets the DI 6 programmable
digital input signal.
Sets the DI 7 programmable
digital input signal.
Sets the DI 8 programmable
digital input signal.
Sets the DI 9 programmable
digital input signal.
Sets the DI 9 programmable
digital input signal.
Setting range
None, Test, Modbus RTU slave,
Extension IO
FbPlug, Modbus RTU, Anybus,
None
Off, On
0 ... 65535
0.0.0.0 ... 255.255.255.255
0.0.0.0 ... 255.255.255.255
0.0.0.0 ... 255.255.255.255
Off, On
1200, 2400, 4800, 9600, 19200,
38400, 57600, 76800, 115200,
125000, 250000,500000, Auto
No parity, Odd parity, Even parity
1 Stop bit, 2 Stop bits
Emergency mode feedback,
Event group 0 ... 6 status,
Fault reset feedback,
Line,
Motor heating feedback,
None,
Phase sequence,
Run reverse status,
Run status,
Sequnce 1 ... 3 Run status,
Sequence 1 ... 3 TOR status,
Slow speed rev feedback,
Slow speed forw feedback,
Stand still brake feedback,
Start 1 ... 3 feedback,
Start feedback,
Start reverse feedback,
Stop feedback,
TOR status,
User defined feedback
Default value
Test
None
Off
0
0.0.0.0
0.0.0.0
255.255.255.0
Off
* There are restrictions
on which baudrates
that can be used for
different protocols. See
separate Table below.
Even parity
1 Stop bit
Line
Phase sequence
Event group 0 status
Eventgroup 1 status
Start feedback
Stop feedback
Eventgroup 2 status
Eventgroup 3 status
Eventgroup 4 status
Eventgroup 5 status
7