Cisco TelePresence SX20 Quick Set Administrator's Manual page 67

Cisco TelePresence SX20 Quick Set
AdministrAtor guide
Table of contents Introduction
Experimental Conference [1..1] Multistream Stream [1..4] Source
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <1/2>
Example: Experimental Conference 1 Multistream Stream 1 Source: 1
Experimental Conference [1..1] ReceiverBasedDownspeeding
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <On/Off>
Example: Experimental Conference 1 ReceiverBasedDownspeeding: Off
Experimental CustomSoftbuttons HoldResume
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
This configuration is used to enable Call Hold and Resume in the OSD. Note that Call Hold and
Resume will be available even if this setting is set to Off, if Multiway is configured.
Requires user role: ADMIN
Value space: <Off/On>
Off: Call Hold and Resume is not available (unless Multiway is configured).
On: Call Hold/Resume is available while the system is in a call. It will be available on
softbuttons, and when receiving incoming calls the user will have the option of holding any
current calls while accepting the new call.
Example: Experimental CustomSoftbuttons HoldResume: Off
Experimental CustomSoftbuttons State [1..2] SoftButton [1..5] Type
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <NotSet/MainSource/PresentationSource/CameraPreset/Actions/
SpeedDial>
Example: Experimental CustomSoftbuttons State 1 Softbutton 1 Type: NotSet
D14908.01 SX20 Administrator Guide (TC5.1) | 2012 FEBRUARY | © 2012 Cisco Systems, Inc. All rights reserved.
Web interface Advanced settings Advanced settings Appendices
Experimental CustomSoftbuttons State [1..2] SoftButton [1..5] Value
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <S: 0, 255>
Example: Experimental CustomSoftbuttons State 1 Softbutton 1 Value: ""
Experimental NetworkServices UPnP Mode
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <On/Off>
Example: Experimental NetworkServices UPnP Mode: Off
Experimental NetworkServices UPnP Timeout
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <0..3600>
Example: Experimental NetworkServices UPnP Timeout: 0
Experimental CTMSSupport Mode
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
This configuration tells whether CTMS (Cisco TelePresence Multipoint Switch) is supported or
not.
Requires user role: ADMIN
Value space: <Off/On>
Off: CTMS is not supported.
On: CTMS is supported.
Example: Experimental CTMSSupport Mode: On
Experimental SystemUnit MenuType
NOTE: This Experimental command can be used 'as is' and will not be further documented. The
Experimental settings WILL change.
Requires user role: ADMIN
Value space: <Indicators/Full>
Example: Experimental SystemUnit MenuType: Full
67
www.cisco.com