Honeywell 30 Series Configuration Manual
  1. Manuals
  2. Brands
  3. Honeywell Manuals
  4. Security Camera
  5. 30 Series
  6. Configuration manual

Honeywell 30 Series Configuration Manual

Hide thumbs Also See for 30 Series:
Table of Contents

Advertisement

Quick Links

Honeywell 30 Series IP Cameras
Configuration Guide
HC30W42R3 HC30W45R3 HC30W45R2
HC30WB5R2 HC30WE2R3 HC30WE5R3
Recommended
Find the latest version of this and other Honeywell 30 Series IP
camera documents on the Honeywell Video website. Go to:
http://www.honeywellvideosystems.com/ndaa/
camera and view/download the latest documentation.
Refer to the Honeywell Open Technology Alliance to learn more
about our open and integrated solutions (go to:
http://www.security.honeywell.com/hota/).
HC30WB2R1 HC30WB5R1
HC30WE5R2 HC30WF5R1
to find your

Advertisement

Table of Contents
loading

Related Manuals for Honeywell 30 Series

Summary of Contents for Honeywell 30 Series

  • Page 1 HC30W42R3 HC30W45R3 HC30W45R2 HC30WB2R1 HC30WB5R1 HC30WB5R2 HC30WE2R3 HC30WE5R3 HC30WE5R2 HC30WF5R1 Recommended Find the latest version of this and other Honeywell 30 Series IP camera documents on the Honeywell Video website. Go to: http://www.honeywellvideosystems.com/ndaa/ to find your camera and view/download the latest documentation.
  • Page 3 Revisions Issue Date Revisions 04/2019 New document. 04/2019 Add Compatible SD Card V1-A 05/2019 Add Fisheye features; Modify special characters in password; Add HLC; Add Pixel Calculator; Modify HTTPS; Add Certificate Request and upload files; Modify Motion detection (intrusion detection, people detection); Add audio settings;...

  • Page 4: Cautions And Warnings

    Cautions and Warnings WARNING Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. WARNING To ensure compliance with electrical safety standards this product is intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”, on the unit, output rated 12 V DC, minimum 0.7A, Tma=60°C or from Power over Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE 802.3af PoE standard.

  • Page 5: Fcc Compliance Statement

    FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

  • Page 6: Safety Instructions

    Honeywell will repair or replace, at its sole option, free of charge, any defective products returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service at 1.800.323.4576 for assistance or to request a Return Merchandise Authorization (RMA) number.

  • Page 7: Table Of Contents

    Table of Contents Introduction................................ 1 Overview ....................................1 Key Features ..................................1 Accessing the Camera ............................. 3 Installing the IPC Tool Utility ............................3 Discovering Your Camera on the Network ......................3 Assigning a New IP Address to Your Camera ......................4 Upgrading the Camera’s Firmware ..........................
  • Page 8 PTZ Operations ................................39 Home Location Settings .............................39 Preset and Patrol Settings ..........................39 Misc Settings ................................40 PTZ Operations on Main Page .........................40 PTZ Operations (Fisheye Model) ........................40 Configuring Network Settings ........................43 Configuring Network General Settings ......................43 Configuring Streaming Protocols ........................46 Configuring DDNS Settings ..........................49 Configuring QoS Settings ..........................50 Configuring SNMP Settings ..........................51...
  • Page 9 Privilege Management ............................87 Configuring Access List Settings ..........................87 General Settings ..............................88 Filter ....................................88 Administrator IP address ............................89 Viewing System Information ........................90 Log ....................................90 Version ..................................91 Troubleshooting............................. 92 Appendix ................................93 List of Symbols .................................93...
  • Page 10 Figures Figure 2-1 IPC Tool ................................... 4 Figure 3-1 Security Certificate Problem ..........................7 Figure 3-2 Change Password ..............................7 Figure 3-3 Login Page ..................................7 Figure 3-4 Safety Problem ................................8 Figure 3-5 Security Certificate Problem ..........................8 Figure 3-6 Login Page ..................................8 Figure 3-7 Main Page..................................
  • Page 11 Figure 5-13 HTTP ....................................52 Figure 5-14 Certificate Request ...............................52 Figure 5-15 Certificate Request Created ..........................53 Figure 5-16 Upload files ................................53 Figure 5-17 IEEE 802.1X Configurations – EAP-PEAP ....................54 Figure 5-18 IEEE 802.1X Configurations – EAP-TLS....................54 Figure 6-1 Motion Detection ..............................55 Figure 6-2 Configuring Motion Detection Settings......................56 Figure 6-3 Item Size Indicator ..............................57 Figure 6-4 Intrusion Detection ..............................57...
  • Page 12 Tables Table 3-1 Live View Window Controls............................10 Table 3-2 Fisheye Display Mode ..............................13 Table 4-1 Stream and Frame Size Matrix ..........................31 Table 7-1 Compatible SD Card ..............................72 Table 10-1 Troubleshooting ..............................92...

  • Page 13: About This Document

    About This Document This document provides instructions for accessing, configuring, and operating the Honeywell 30 Series IP cameras. This document is intended for system installers, administrators, and operators. Overview of Contents This document contains the following chapters and appendixes: •...

  • Page 15: Introduction

    Key Features, page 1 Overview Honeywell 30 Series IP cameras integrate traditional camera and network video technology, combining video data collection and transmission. These flexible, fully featured cameras are the ideal choice for a wide range of indoor and outdoor surveillance applications.
  • Page 16 Performance Series IP Camera Software Configuration Guide • Recording over Internet, files stored on client PC • Network storage (NAS) Network Monitoring • Latency time less than 500ms (network bandwidth support required) • Up to 10 connections • Compatible with the following network protocols: IPv4, IPv6, TCP/IP, HTTP, HTTPS, UPnP, RTSP/RTP/RTCP, IGMP, CIFS/SMB, SMTP, DHCP, NTP, DNS, DDNS, CoS, QoS, SNMP, 802.1X, UDP, ICMP, ARP, TLS Network Management...

  • Page 17: Accessing The Camera

    Accessing the Camera 2 Accessing the Camera This chapter contains the following sections: • Installing the IPC Tool Utility, page 3 • Discovering Your Camera on the Network, page 3 • Assigning a New IP Address to Your Camera, page 4 •...

  • Page 18: Assigning A New Ip Address To Your Camera

    Performance Series IP Camera Software Configuration Guide Figure 2-1 IPC Tool Assigning a New IP Address to Your Camera The current IP address of your camera appears in the IP column of the devices list. If you want, you can assign a new static IP address to the camera. To change the IP address of a single camera: 1.

  • Page 19: Upgrading The Camera's Firmware

    Accessing the Camera Upgrading the Camera’s Firmware Before you begin using your camera, make sure you have the latest firmware installed. You can upgrade a single camera or multiple cameras at the same time. To upgrade a single camera: 1. Select the camera that you want to upgrade from the devices list. 2.

  • Page 20: Logging In And Viewing Live Video

    Performance Series IP Camera Software Configuration Guide 3 Logging In and Viewing Live Video This chapter contains the following sections: • Logging In to the Camera via the Web Client, page 6 • Using the Main Page, page 9 Logging In to the Camera via the Web Client Using the web client, you can monitor live video, play back recorded video, and configure camera settings.

  • Page 21: Figure 3-1 Security Certificate Problem

    Logging In and Viewing Live Video Figure 3-1 Security Certificate Problem For how to resolve the security certificate problem, see Export CA Certificate on page 85. 3. For security purposes, you are required to create a new secure password at the first login. Figure 3-2 Change Password The password must be at least 8 characters in length and contain at least one uppercase letter, one lowercase letter, one number, and one special character (!?@#$%=+*-_:,.&^~).

  • Page 22: Figure 3-4 Safety Problem

    Performance Series IP Camera Software Configuration Guide Logging in Via Google Chrome 1. Open Google Chrome, type the camera’s IP address in the address bar, and then click Enter. For example, if your camera’s IP address is 192.168.1.108, you would type https://192.168.1.108.

  • Page 23: Using The Main Page

    Logging In and Viewing Live Video Chrome 71 (or later) is supported for H.264 video. Chrome is not Note supported for H.265 video. Using the Main Page The main page has the following areas: video stream settings area, manual triggers area, system menu, live view resize buttons, live view controls toolbar and live video window.

  • Page 24: Host Name

    Performance Series IP Camera Software Configuration Guide Host Name You can change the host name according to your needs. For more information, see Configuring System General Settings on page 80. System Menu When you log in to the camera using the web client, the main page opens by default. To access the settings page, language page or to log out, select the corresponding tab.

  • Page 25: Manual Triggers Settings

    Logging In and Viewing Live Video Icon Control Description Click to record the video clip in MP4 file format and save it to your computer. You can play the video clip by VLC player. Press the Stop MP4 Recording button to end recording. When you exit the web browser, video recording stops accordingly.

  • Page 26: Resize Buttons

    Performance Series IP Camera Software Configuration Guide The PTZ buttons on the panel are not operational unless you are Note showing only a portion of the full image. If the live view window is displaying the full view, the PTZ buttons are not functional. Resize Buttons Click Auto, the video window will resize automatically to fit the monitor.

  • Page 27: Figure 3-10 Fisheye Display Mode

    Logging In and Viewing Live Video Figure 3-10 Fisheye Display Mode Table 3-2 Fisheye Display Mode Display Mode Description One Original fisheye view One Panoramic view One Regional view 1P2R One Panoramic and two Regional views (Wall mount) Two Panoramic views 1P3R One Panoramic and three Regional views (Wall mount)

  • Page 28: Figure 3-11 1O (Original) Display Mode

    Performance Series IP Camera Software Configuration Guide Figure 3-11 1O (Original) Display mode 1P (One Panoramic) Display Mode With the image correction algorithms in firmware, the hemispheric image is transformed into a rectilinear stripe in the 1P display mode. You can use the PTZ panel or simply use mouse drags to quickly move through the 360º...

  • Page 29: Figure 3-13 1R (One Regional) Display Mode

    Logging In and Viewing Live Video 1R (One Regional) Display Mode The 1R mode provides access to one image section within the hemisphere. You can zoom in or out (using the mouse wheel or PTZ panel) or travel to other areas in the hemisphere using mouse clicks and drags.

  • Page 30: Figure 3-14 2P (Two Panoramic View) Display Mode

    Performance Series IP Camera Software Configuration Guide Figure 3-14 2P (Two Panoramic View) Display mode 1P3R (One Panoramic and Three Regional) Display Mode The 1P2R mode provides access to two regional views and the reference to their relative positions on a panoramic view. This display mode is available only when you select the Wall mount type, see the Mount type section in General Settings on page 20.

  • Page 31: Figure 3-15 1O3R (One Original & Three Regional) Display Mode

    Logging In and Viewing Live Video Figure 3-15 1O3R (One Original & Three Regional) Display mode If you select a regional window, you can see the position of the regional window in the original window. Figure 3-16 Regional Window Selection...

  • Page 32: Figure 3-17 4R (Four Regional) Display Mode

    Performance Series IP Camera Software Configuration Guide • In a Regional view displaying 100% of video feed (via the Resize buttons - see Resize Buttons on page 12), your mouse wheel can be used to scroll the view window Note vertically before you click a live image.

  • Page 33: Figure 3-18 1O8R (One Original And Eight Regional) Display Mode

    Logging In and Viewing Live Video Figure 3-18 1O8R (One Original and Eight Regional) Display mode If you change the position of a view in hemisphere, e.g., the #3 window, you may lose the configuration change by switching to Note another display mode.

  • Page 34: Configuring Camera Settings

    Performance Series IP Camera Software Configuration Guide 4 Configuring Camera Settings This chapter contains the following sections: • Configuring Camera Properties, page 20 • Configuring Video Settings, page 30 • Configuring Digital PTZ Settings, page 36 Configuring Camera Properties Go to Setup Camera Setup  Properties. This section describes how to configure the image settings of camera (picture, exposure, lighting compensation, white balance, day and night, IR light, etc.).

  • Page 35: Figure 4-1 General Settings

    Configuring Camera Settings Figure 4-1 General Settings Video Settings Video Title: Enter a name that will be displayed on the title bar of the live video. Show timestamp and video title in video and snapshots: Check to display timestamp and video title in live video and snapshots.

  • Page 36: Figure 4-2 Video Orientation

    Performance Series IP Camera Software Configuration Guide The power line frequency is changed, you must disconnect and Note reconnect the power cord of the camera in order for the new setting to take effect. Video orientation: • Flip: vertically reflect the display of the live video; •...

  • Page 37: Ir Control Settings

    Configuring Camera Settings In day mode, the camera switches on the IR cut filter at all times to block infrared light from reaching the sensor so that the colors will not be distorted. • Night mode In night mode, the camera switches off the IR cut filter at all times for the sensor to accept infrared light, thus helping to improve low light sensitivity.

  • Page 38: Image Settings

    Performance Series IP Camera Software Configuration Guide Image Settings Go to Setup Camera Setup  PropertiesImage Settings. On this page, you can configure the White balance and adjust Image parameters. Two sets of image settings are available: • In Normal Light Mode tab, configure normal situations for image settings. •...

  • Page 39: Exposure

    Configuring Camera Settings • Manual: Drag the slider to change the preferred level of Gamma correction towards higher contrast or towards the higher luminance for detailed expression for both dark and lighted areas of an image. The Gamma curve function is disabled when the WDR feature in Note Exposure settings is enabled.

  • Page 40: Figure 4-6 Exposure

    Performance Series IP Camera Software Configuration Guide Figure 4-6 Exposure Measurement Window Measurement Window: This function allows users to set measurement window(s) for low light compensation. For example, where low-light objects are posed against an extremely bright background. You may want to exclude the bright sunlight shining through a building's corridor.

  • Page 41: Figure 4-8 Ae Speed Adjustment

    Configuring Camera Settings • Center: This option will automatically add an inclusive window in the middle of the window and give the necessary light compensation. • HLC (Highlight Compensation): Firmware detects strong light sources and compensates on affected spots to enhance the overall image quality. For example, the HLC helps reduce the glares produced by spotlights or headlights.

  • Page 42: Focus

    Performance Series IP Camera Software Configuration Guide Focus This function only applies to HC30W45R2/ HC30WB5R2/ Note HC30WE5R2 motorized focus/zoom cameras. Go to Setup Camera Setup  PropertiesFocus. Figure 4-10 Focus To perform the automated Focus function: 1. Select from the bottom of the screen whether you want to perform focus adjustment on the Full view or within a Custom focus window.

  • Page 43: Privacy Mask

    Configuring Camera Settings It is recommended that this function be used only when you have a solid object in your view window that is showing a consistent color or Note texture. This function will not take effect if you set the focus window on a distant background.

  • Page 44: Pixel Calculator (Fisheye Model Only)

    Performance Series IP Camera Software Configuration Guide Pixel Calculator (Fisheye Model Only) With the pixel calculator feature, you can estimate a coverage area, the distance from the subject, and place a ruler or an object of known size. You can then draw a calculator frame to cover the subject of your interest.

  • Page 45: Video Mode

    Configuring Camera Settings This section describes how to configure video mode and video streaming properties (format, resolution, frame rate, bit rate, I-frame interval, etc.). Video Mode Go to Setup Camera Setup  Video Mode. This function only applies to HC30W45R3/HC30WE5R3/HC30WB5R1/ Note HC30W45R2/HC30WB5R2/HC30WE5R2/HC30WF5R1 cameras.
  • Page 46 Performance Series IP Camera Software Configuration Guide Model Main Stream Sub Stream Third Stream 2560x1920/2048x1536/1600x1200/ 800x600/ 640x480 HC30W45R3 (5MP) 1280x960/800x600/640x480 640x480 2688x1520/1920x1080/ 1280x720/ 640x360 HC30W45R2 (4MP) 1600x904/1280x720/640x360 640x360 2560x1920/2048x1536/1600x1200/ 800x600/ 640x480 HC30W45R2 (5MP) 1280x960/800x600/640x480 640x480 1920×1080/1600x904/ 1280x720/ 640x360 HC30WB2R1 1360x768/1280x720/640x360 640x360 1280x720/ 640x360...

  • Page 47: Figure 4-14 Video Stream

    Configuring Camera Settings Figure 4-14 Video Stream Viewing Window Click Viewing Window to open the viewing region settings page. On this page, you can configure the Region of Interest and the Frame Size for a video stream. For example, you can crop only a portion of the image that is of your interest, and thus save the bandwidth needed to transmit the video stream.
  • Page 48 Performance Series IP Camera Software Configuration Guide The camera provides real-time H.265, H.264 and MJPEG compression standards (Triple Codec) for real-time viewing. • If the H.265 or H.264 mode is selected, the video is streamed via RTSP protocol. • If the JPEG mode is selected, the camera sends consecutive JPEG images to the client, producing a moving effect similar to a filmstrip.

  • Page 49: Figure 4-15 Video Quality

    Configuring Camera Settings Smart FPS In a static scene, the algorithm puts old frames in queue when no motions occur in scene. When motions occur, the encoding returns to normal to deliver real-time streaming. By queuing the old frames from a static scene, both the computing efforts and the size of P frames are reduced.

  • Page 50: Configuring Audio Settings

    Performance Series IP Camera Software Configuration Guide In this way, you may set up an ROI window as a privacy mask by covering a protected area using an ROI window, while the rest of the screen becomes the non-interested area. You may then configure the non-interested area to have a high image quality, or vice versa.

  • Page 51: Configuring Digital Ptz Settings

    Configuring Camera Settings Figure 4-16 Audio Mute: Check to disable audio transmission from the Network Camera to all clients. Internal microphone input gain: Select the gain of the internal audio input according to ambient conditions. Adjust the gain from 0% (least) to 100% (most). Audio type: Select audio codec as G.711 or G.726 and the bit rate.

  • Page 52: Figure 4-17 Ptz Settings

    Performance Series IP Camera Software Configuration Guide Figure 4-17 PTZ Settings...

  • Page 53: Ptz Operations

    Configuring Camera Settings PTZ Operations Move: Click to move the video image up, down, to the left or to the right. To return to the home location, click Home. Zoom: Click to zoom out the video image, or click to zoom in the video image. Pan Speed: Select a speed (-5 to 5) from the dropdown list.

  • Page 54: Misc Settings

    Performance Series IP Camera Software Configuration Guide Misc Settings Zoom factor display: Check to display zoom factor on the video image. PTZ Operations on Main Page Global View In addition to using the PTZ control panel, you can also use the mouse to drag or resize the floating frame to pan/tilt/zoom the viewing region.

  • Page 55: Figure 4-18 Ptz Settings (Fisheye Model)

    Configuring Camera Settings Figure 4-18 PTZ Settings (Fisheye Model) You can create preset positions in the hemisphere covered by the fisheye lens. A total of 20 preset positions can be configured. Follow the steps below to configure preset positions and arrange them in a rotational tour through different positions.
  • Page 56 Performance Series IP Camera Software Configuration Guide 3. After you selected an area of interest, enter a name for the new position, which can contain up to 40 alphabetic and numeric characters. 4. Click Add to enable the settings. The preset positions will be listed on the User preset locations.

  • Page 57: Configuring Network Settings

    Configuring Network Settings 5 Configuring Network Settings This chapter contains the following sections: • Configuring Network General Settings, page 43 • Configuring Streaming Protocols, page 46 • Configuring DDNS Settings, page 49 • Configuring QoS Settings, page 50 • Configuring SNMP Settings, page 51 •...
  • Page 58 Performance Series IP Camera Software Configuration Guide • IP address: 1. You can make use of IPC Tool in the software CD to easily set up the camera on LAN. Accessing the Camera on page 3. 2. Enter the Static IP, Subnet mask, Default router, and Primary DNS provided by your ISP or network administrator.

  • Page 59: Figure 5-2 Enable Ipv6

    Configuring Network Settings To enable UPnP in Windows 7: 1. Go to Start Control Panel Network and Internet  Network and Sharing Center. 2. On the left pane, click Change advanced sharing settings. 3. On your current network profile, in the Network discovery area, click Turn on network discovery, and then click Save changes.

  • Page 60: Configuring Streaming Protocols

    Performance Series IP Camera Software Configuration Guide Figure 5-4 IPv6 Address Link-global IPv6 address/network mask Link-local IPv6 address/network mask Follow the steps below to link to an IPv6 address: 1. Open your web browser. 2. Enter the link-global or link-local IPv6 address in the address bar of your web browser. 3.

  • Page 61: Figure 5-6 Streaming Protocols - Http

    Configuring Network Settings Figure 5-6 Streaming Protocols - HTTP To utilize HTTP authentication, make sure that you have set a password for the camera first. For more information, see Configuring User Accounts Settings on page 86. Authentication (digest): User credentials are encrypted with MD5 algorithm which provide better protection against unauthorized accesses.

  • Page 62: Figure 5-8 Multicast Settings

    Performance Series IP Camera Software Configuration Guide Authentication (digest): User credentials are encrypted with MD5 algorithm which provides better protection against unauthorized access. Access name for stream 1 ~ 3: The camera supports multiple streams simultaneously. The access name is used to differentiate the streaming source. If you want to use an RTSP player to access the camera, you have to set the video mode to H.264 or H.265 and use the following RTSP URL command to request transmission of the streaming data.

  • Page 63: Configuring Ddns Settings

    Configuring Network Settings Multicast video port/Multicast RTCP video port: The ports can be changed to values between 1025 and 65535. The multicast video port must be an even number and the multicast RTCP video port number is the multicast video port number plus one, and thus is always odd.

  • Page 64: Configuring Qos Settings

    Performance Series IP Camera Software Configuration Guide Configuring QoS Settings Go to Setup Network Setup Qos. Quality of Service (QoS) is a network security mechanism. It fixes problems with network delays and jams. For network service, the quality of service includes the transmission bandwidth, delay, and packet loss, for example.

  • Page 65: Configuring Snmp Settings

    Configuring Network Settings Figure 5-11 QoS/DSCP Specify the DSCP value for each application (0~63). Configuring SNMP Settings Go to Setup Network Setup  SNMP. SNMP (Simple Network Management Protocol) is a protocol for collecting, organizing, and exchanging management information between managed devices on a network. The SNMP consists of the following three key components: •...

  • Page 66: Configuring Https Settings

    Performance Series IP Camera Software Configuration Guide • Security name: Choose Read/Write or Read Only and enter the community name according to your NMS settings. • Authentication type: Select MD5 or SHA as the authentication method. • Authentication password: Enter the password for authentication (at least 8 characters). •...

  • Page 67: Figure 5-15 Certificate Request Created

    Configuring Network Settings Enter the information of Country, State or province, Locality, Organization and Organization unit. Click Create. The following figure is displayed: Figure 5-15 Certificate Request Created Click Export to export the certificate request to your local computer. After you get the signing certificate from the certificate issuing authority, click Browse and Upload to import it to the camera.

  • Page 68: Configuring Ieee 802.1X Settings

    Performance Series IP Camera Software Configuration Guide Configuring IEEE 802.1X Settings Go to Setup Network Setup 802.1X. IEEE802.1X is the access control and authentication protocol for local and metropolitan area networks. It uses a port-based network access control protocol to restrict unauthorized user and/or device access to the LAN.

  • Page 69: Configuring Video Analytics

    Configuring Video Analytics 6 Configuring Video Analytics This chapter contains the following sections: • Configuring Motion Detection Settings, page 55 • Configuring Tampering Detection Settings, page 59 • Configuring Event Settings, page 60 Configuring Motion Detection Settings Go to Setup Video Analytics  Motion Detection. Figure 6-1 Motion Detection Two sets of motion detection settings are available: •...

  • Page 70: Motion Detection

    Performance Series IP Camera Software Configuration Guide Motion Detection The Motion Detection detects motions in customized windows. If a motion is detected, the frame of the customized window will become flashing red. To enable motion detection: 1. Click New to add a new motion detection window. 2.

  • Page 71: Intrusion Detection

    Configuring Video Analytics The Item Size Indicator will rise or fall depending on the variation between sequential images. When motions are detected by the camera and are considered to exceed the preset threshold, the red bar rises. Meanwhile, the motion detection window will be outlined in red. Photos or videos can be captured instantly and configured to be sent to a remote server (i.e.

  • Page 72: People Detection

    Performance Series IP Camera Software Configuration Guide 1. Click New to add a new intrusion detection window. 2. In the Window Name text box, enter a name for the intrusion detection window. To delete a window, click the mark on the right of the window name. 3.

  • Page 73: Configuring Tampering Detection Settings

    Configuring Video Analytics Only one kind of motion detection (motion detection, intrusion Note detection or people detection) can be enabled at a time. Configuring Tampering Detection Settings Go to Setup Video Analytics  Tampering Detection. This section explains how to configure camera tamper detection settings. With tamper detection, the camera is capable of detecting incidents such as redirection, blocking or defocusing, or even spray paint.

  • Page 74: Configuring Audio Detection

    Performance Series IP Camera Software Configuration Guide Configuring Audio Detection Go to Setup Video Analytics  Audio Detection. Note Only HC30WF5R1 supports this function. Audio detection, along with video motion detection, is applicable in the following scenarios: • Detection of activities not covered by camera view, e.g., a loud input by gun shots or breaking a door/ window.

  • Page 75: Figure 6-8 Audio Detection Profile

    Configuring Video Analytics • The volume numbers (0~100) on the left side of wave diagram does not represent decibel (dB). Sound intensity level has already been mapped to preset values. You can, however, use the real-world inputs at your installation site that are shown on the wave diagram to configure an alarm level.

  • Page 76: Configuring Event Settings

    Performance Series IP Camera Software Configuration Guide Configuring Event Settings Go to Setup Video Analytics  Event Settings. This section describes how to configure the camera to respond to particular situations (event). A typical application is that when a motion is detected, the camera sends buffered images to an e-mail address as notifications.

  • Page 77: Figure 6-10 Event

    Configuring Video Analytics Figure 6-10 Event • Event name: Enter a name for the event setting. • Enable this event: Check to enable the event setting. • Priority: Select the relative importance of this event (High, Normal, or Low). Events with a higher priority setting will be executed first.

  • Page 78: Figure 6-11 Trigger Sources

    Performance Series IP Camera Software Configuration Guide Figure 6-11 Trigger Sources Video motion detection This option makes use of the built-in motion detection mechanism as a trigger source. To enable this function, you need to configure a Motion Detection Window first. For more information, see Configuring Motion Detection Settings on page 55.

  • Page 79: Figure 6-12 Action

    Configuring Video Analytics Figure 6-12 Action Backup media if the network is disconnected: Select this option to backup media files to SD card if the network is disconnected. This function will apply after you configure the Email, HTTP or NAS notification. For example, if a snapshot is supposed to be delivered to an Email receiver, in the event of network failure, the snapshot will be saved in the SD card.

  • Page 80: Figure 6-13 Add Server

    Performance Series IP Camera Software Configuration Guide Figure 6-13 Add Server Server type - Email Select to send the media files via email when a trigger is activated. • Server name: Enter a name for the server setting. • Sender email address: Enter the email address of the sender. •...

  • Page 81: Figure 6-14 Server Type - Http

    Configuring Video Analytics Figure 6-14 Server type – HTTP • Server name: Enter a name for the server setting. • URL: Enter the URL of the HTTP server. • User name: Enter the user name if necessary. • Password: Enter the password if necessary. To verify if the HTTP settings are correctly configured, click Test.

  • Page 82: Figure 6-15 Network Storage

    Performance Series IP Camera Software Configuration Guide Figure 6-15 Network storage Add Media Click Add media to open the media setting window. You can specify the type of media that will be sent when a trigger is activated. A total of 5 media settings can be configured. There are three choices of media types available: Snapshot, Video Clip, and System log.

  • Page 83: Figure 6-17 Media Type - Video Clip

    Configuring Video Analytics Select to send snapshots when a trigger is activated. • Media name: Enter a name for the media setting. • Source: Select to take snapshots from any of the video streams. • Send x pre-event images: The camera has a buffer to temporarily hold data up to a certain limit. Enter a number to decide how many images to capture before a trigger is activated.

  • Page 84: Figure 6-18 Event Settings Examples

    Performance Series IP Camera Software Configuration Guide The camera has a buffer to temporarily hold data up to a certain limit. Enter a number to decide the duration of recording before a trigger is activated. Up to 9 seconds can be set. •...
  • Page 85 Configuring Video Analytics You can only delete a server setting when it is not applied in an existing event setting. To remove a media setting from the list, select a media name and click Delete. You can only delete a media setting when it is not applied in an existing event setting.

  • Page 86: Configuring Storage Settings

    Performance Series IP Camera Software Configuration Guide 7 Configuring Storage Settings This chapter contains the following sections: • SD Card Management, page 72 • Content Management, page 74 • Recording Settings, page 76 SD Card Management Go to Setup Storage Setup SD Card Management. This section describes how to manage the local storage on the camera.

  • Page 87: Sd Card Status

    Configuring Storage Settings SD Card Status This tab shows the status and reserved space of your SD card. Remember to format the SD card when using it for the first time, see SD Card Format on page 73. Figure 7-1 No SD Card Figure 7-2 SD Card Onboard SD Card Format The Linux kernel EXT4 file system format applies to SD card larger than 32GB.

  • Page 88: Content Management

    Performance Series IP Camera Software Configuration Guide For example, if you enter “7 days”, the recorded files will be stored on the SD card for 7 days. Click Save to enable your settings. Content Management Go to Setup Storage Setup Content Management. This section describes how to manage the content of recorded videos on the camera.

  • Page 89: Figure 7-6 Search Results

    Configuring Storage Settings Figure 7-6 Search Results • Play: Click on a search result and a Play window will be displayed for immediate review of the selected file. Figure 7-7 Play • Download: Click on a search result and click Download, and a file download window will pop up for you to save the file.

  • Page 90: Recording Settings

    Performance Series IP Camera Software Configuration Guide • Lock/Unlock: Select the checkbox in front of a desired search result, then click this button. The selected items will become Locked, which will not be deleted during cyclic recording. You can click again to unlock the selections. •...

  • Page 91: Figure 7-9 Recording Settings Details

    Configuring Storage Settings Figure 7-9 Recording Settings Details • Recording name: Enter a name for the recording setting. • Enable this recording: Select this option to enable video recording. • With adaptive recording: Select this option will activate the frame rate control according to alarm trigger. The frame control means that when there is a triggered alarm, the frame rate will raise up to the value you’ve configured on the Video quality page.

  • Page 92: Setting Up A Recording

    Performance Series IP Camera Software Configuration Guide • Priority: Select the relative importance of this recording (High, Normal, or Low). Recording with a higher priority setting will be executed first. • Source: Select a video stream as the recording source. To enable recording notification, configure Event settings first, see Note Configuring Event Settings...

  • Page 93: Adding Nas Server

    Configuring Storage Settings Figure 7-10 Recording 1 • Click Recording 1 (Name): Opens the Recording Settings page to modify. • Click ON (Status): The Status will become OFF and stop recording. • Click SD (Destination): Opens the file list of recordings. Adding NAS Server Figure 7-11 Add NAS Server Click Add NAS server to open the server setting window and follow the steps below to set up:...

  • Page 94: Configuring System Settings

    Performance Series IP Camera Software Configuration Guide 8 Configuring System Settings This chapter contains the following sections: • Configuring System General Settings, page 80 • Configuring Maintenance Settings, page 81 • Configuring User Accounts Settings, page 86 • Configuring Access List Settings, page 87 Configuring System General Settings Go to Setup System Setup General Settings.

  • Page 95: Configuring Maintenance Settings

    Configuring System Settings Keep current date and time: Select this option to preserve the current date and time of the camera. The camera’s internal real-time clock maintains the date and time even when the power of the system is turned off. Synchronize with computer time: Select this option to synchronize the date and time of the camera with the local computer.

  • Page 96: Rebooting The Camera

    Performance Series IP Camera Software Configuration Guide Note Do not power off the camera during the upgrade. Follow the steps below to upgrade the firmware: 1. Click Browse… and locate the firmware file. 2. Click Upgrade. The camera starts to upgrade and will reboot automatically when the upgrade completes.

  • Page 97: Figure 8-3 Import/Export Files

    Configuring System Settings Figure 8-3 Import/Export Files Export daylight saving time configuration file Follow the steps below to export daylight saving time configuration file from the camera and set the start and end time of DST. 1. Click Export next to Export the daylight saving time configuration file. 2.

  • Page 98: Figure 8-4 Edit Language String

    Performance Series IP Camera Software Configuration Guide Export Language File The camera supports the following languages: English, Deutsch, Español, Français, Italiano, 日本語, Português,Pусский and 繁體中文. If your language is not listed, perform the following steps to customize the camera language. Taking the English language file for example: 1.
  • Page 99 When you log in to the camera’s web client for the first time, some browsers may display a warning that the connection is not private/secure. To access the web client, you must install a Honeywell-signed security certificate. 1. Click Export to save the root certificate (ca.crt) on your local computer.

  • Page 100: Configuring User Accounts Settings

    Performance Series IP Camera Software Configuration Guide If the power is disconnected during firmware upgrade or if there is unknown reason causing abnormal LED status, and a Restore cannot recover normal working condition, you can perform the following steps to activate the camera with its backup firmware: a.

  • Page 101: Privilege Management

    Configuring System Settings Role Privilege Administrator Full control Live, Language, Special URL for configuring camera Operator parameters Viewer Live, Language Access rights are sorted by user privilege (Administrator, Operator, and Viewer). Only administrators can access the Configuration page. Viewers can only access the main page for live viewing.

  • Page 102: General Settings

    Performance Series IP Camera Software Configuration Guide Figure 8-7 Access List General Settings Maximum number of concurrent streaming: Simultaneous live viewing for 1~10 clients (including stream 1 to stream 3). The default value is 10. If you modify the value and click Save, all current connections will be disconnected and automatically attempt to re-link (IE Explorer or Quick Time Player).

  • Page 103: Administrator Ip Address

    Configuring System Settings • The IPv6 access list column will not be displayed unless you enable IPv6 on the Network page. For more information about IPv6 Settings, see Enable IPv6 on page Note • The Range rule only applies to IPv4 addresses. Administrator IP address Always allow the IP address to access this device: Check it and add the Administrator’s IP address in this field to make sure the Administrator can always connect to the device.

  • Page 104: Viewing System Information

    Performance Series IP Camera Software Configuration Guide 9 Viewing System Information This chapter contains the following sections: • Log, page 90 • Version, page 91 Go to Setup Information Logs. System Log System log displays the system events in a chronological order. The system log is stored in the camera’s buffer area and will be deleted after the camera is rebooted.

  • Page 105: Version

    Viewing System Information Figure 9-2 Access Log Version Go to Setup Information Version. On the Version page, you can view the software version. Figure 9-3 Version...

  • Page 106: 10 Troubleshooting

    Performance Series IP Camera Software Configuration Guide 10 Troubleshooting Refer to the following guidelines to troubleshoot any performance issues. If you require additional assistance, contact Honeywell Technical Support (see back cover for contact information). Table 10-1 Troubleshooting Issues Solutions • Use the player located on the CD that came Cannot play downloaded file with your camera.

  • Page 107: 11 Appendix

    Appendix 11 Appendix List of Symbols The following is a list of symbols that may appear on the camera: Symbol Explanation The WEEE symbol. This symbol indicates that when the end-user wishes to discard this product, it must be sent to separate collection facilities for recovery and recycling. By separating this product from other household-type waste, the volume of waste sent to incinerators or landfills will be reduced, and thus natural resources will be conserved.
  • Page 108 Document 800-25049V1 – Rev A – 05/2019 © 2019 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell cannot assume responsibility for any consequences resulting from the use thereof.

This manual is also suitable for:

Hc30w42r3Hc30w45r2Hc30wb5r1Hc30wb2r1Hc30wb5r2Hc30we2r3 ... Show all

Table of Contents