Honeywell MRP-2002 Instruction Manual page 57

Master Programming Level
Pressing 1 while viewing the Adjective/Noun Screen will cause the following screen(s) to be
displayed. Note that the keyboard down arrow key must be pressed to see all the Adjective screens.
Press the number corresponding to the adjective that is to be used as a descriptor for the location of
the detector currently being programmed. When an adjective has been selected, it will appear at the
top of the display as indicated by the asterisks.
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=NORTH
2=SOUTH
3=EAST
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=MAIN
2=FIRST
3=2ND
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=FLOOR4
2=FLOOR5
3=ROOM
Pressing 2 while viewing the Adjective/Noun Screen will cause the following screen(s) to be
displayed. Note that the keyboard down arrow key must be pressed to see all the Noun screens.
Press the number corresponding to the noun that is to be used as a descriptor for the location of the
detector currently being programmed. When a noun has been selected, it will appear at the top of
the display as indicated by the asterisks.
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=BASEMENT
2=BOILER RM
3=CLASSROOM
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=HVAC ROOM
2=ISLAND
3=KITCHEN
Description
INPUT ZONE #
The Description selection allows the programmer to enter additional information about the detector
1=ADJECTIVE/NOUN
2=DESCRIPTION
currently being programmed. This information will be displayed as part of the device label on the
display. Pressing 2 while viewing Edit Input Zone Screen #3 will cause the following screen to be
Edit Input Zone Screen #3
displayed:
A flashing cursor will appear at the first asterisk to the left. The programmer can enter additional
descriptive information about the device being programmed. This information will appear on the
display along with the standard device label information.
A maximum of 20 characters (including spaces) can be entered. To enter alphanumeric characters
from the keypad, repeatedly press the appropriate key until the desired character is displayed in the
first position. For example, to enter the letter B, press the 2 (ABC) key three times to toggle through
MRP-2002 Series Instruction Manual — P/N 53049:E5 7/28/2016
Adjective Screen #1
Adjective Screen #4
Adjective Screen #7
Noun Screen #1
Noun Screen #4
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=WEST
2=FRONT
3=CENTER
Adjective Screen #2
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=3RD
2=4TH
3=5TH
Adjective Screen #5
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=COMPUTER RM
2=CONTROL RM
3=DATA ROOM
Noun Screen #2
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=ROOM
2=STOREROOM
3=TELCO ROOM
Noun Screen #5
ZONE # DESCRIPTION
PRESS ENTER IF DONE
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
Adjective/Noun Screen
Programming
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=REAR
2=UPPER
3=LOWER
Adjective Screen #3
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=FLOOR1
2=FLOOR2
3=FLOOR3
Adjective Screen #6
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=DOCUMENT RM
2=ELECTRIC RM
3=GARAGE
Noun Screen #3
✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱✱
1=UPS ROOM
2=VAULT
Noun Screen #6
57