Yamaha A4000 Owner's Manual page 275

2. Channel messages
Channel messages are received as follows.
When Program Mode = Single and Omni SW is on, The Note ON/OFF, Control Change, Pitch
Bend, After Touch, and Program Change channels have no meaning.
When Program Change SW is enabled and Program Mode = Single the Basic Receive Channel is
used; when Program Mode = Multi the Part 1 receive channel is used. No program change occurs
when off. However, when a program change is received during internal MIDI sequencer record-
ing, the program change is not recorded even if the Program Change SW is off.
Transmission is performed when the internal MIDI sequencer is playing, and when the KNOB
Control function and FKey Play function are being used.
When the MIDI sequencer is playing, the MIDI events that are played back are transmitted to the
internal tone generator, and also simultaneously transmitted via MIDI OUT.
When Knob control used, a value related to the number of rotations is transmitted for the selected
Ch and Control#.
When the FKey Play function is used, Note On/Off messages will be transmitted on the specified
channel with the specified note number and velocity. The velocity used when transmitting a Note
Off message is fixed. Note Off messages will have a velocity of 0 if the form $8n is used, and if
the form $9n is used the velocity will be determined case by case.
2.1. Reception
2.1.1. Note off
Note range = C-2 — G8
Velocity range = ignored
2.1.2. Note on/off
Note range = C-2 — G8
Velocity range = 0 — 127
2.1.3. Polyphonic aftertouch
Not received.
2.1.4. Control changes
The following parameters can be controlled.
Parameters which function for each program.
cntrl# parameter
5 Program Portamento Time
0-120 Program Portamento Rate/Time
0-120 LFO S/H Speed
0-120 AD Input Pan
0-120 AD Input Level
0-120 AD Input L Pan
0-120 AD Input R Pan
0-120 AD Input L Level
0-120 AD Input R Level
0-120 Program Level
0-120 EF1 Level
0-120 EF1 Pan
0-120 EF1 Width
0-120 EF1 Parameter 1 — 16
0-120 EF2 Level
0-120 EF2 Pan
0-120 EF2 Width
0-120 EF2 Parameter 1 — 16
0-120 EF3 Level
0-120 EF3 Pan
0-120 EF3 Width
0-120 EF3 Parameter 1 — 16
0-120 EF4 Level
0-120 EF4 Pan
0-120 EF4 Width
0-120 EF4 Parameter 1 — 16
0-120 EF5 Level
0-120 EF5 Pan
0-120 EF5 Width
0-120 EF5 Parameter 1 — 16
0-120 EF6 Level
0-120 EF6 Pan
0-120 EF6 Width
0-120 EF6 Parameter 1 — 16
0-120 Program LFO Depth
0-120 Control 1 Range
0-120 Control 2 Range
0-120 Control 3 Range
0-120 Control 4 Range
Parameters marked by "*" depend on the Program Control settings.
data range
0 — 127
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 * (A5000 only)
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
Parameters which function for each MIDI channel of a program
cntrl# parameter
7 Volume(Level)
10 Pan
64 Sustain
65 Portament ON/OFF
66 Sostenute
Parameters which function for samples or sample banks
cntrl# parameter
0-120 Pitch Mod Depth
0-120 Amp Mod Depth
0-120 Cutoff Mod Depth
0-120 Cutoff Bias
0-120 Filter Q/Width
0-120 Pan Bias
0-120 Pitch Bias
0-120 Sample Level
0-120 LFO Speed
0-120 LFO Delay
0-120 AEG Attack
0-120 AEG Decay
0-120 AEG Sustain Level
0-120 AEG Release
0-120 PEG Attack
0-120 PEG Decay
0-120 PEG Release
0-120 PEG Init Level
0-120 PEG Sustain Level
0-120 FEG Attack
0-120 FEG Decay
0-120 FEG Release
0-120 FEG Init Level
0-120 FEG Sustain Level
0-120 FEG Level
0-120 Pitch Bend
0-120 Wave Start Address
0-120 Cutoff Distance
0-120 Filter Gain
0-120 Sample Portamento Rate/Time
0-120 Sample Control 1 Range
0-120 Sample Control 2 Range
0-120 Sample Control 3 Range
0-120 Sample Control 4 Range
0-120 Sample Control 5 Range
0-120 Sample Control 6 Range
Parameters marked by "*" depend on the Sample Control settings.
2.1.5. Mode messages
Messages which function always
cntrl# parameter
120 All sound off
121 Reset all controllers
123 All notes off
Messages which function for samples or sample banks
cntrl# parameter
126 mono mode
127 poly mode
2.1.6. Program changes
When a program change message is received, the corresponding program is selected for playback
and editing. Nothing occurs if the Program Change SW is disabled (even when internal sequencer
recording is off). If Program Mode = Single, program change is received via the Basic Receive
Channel (any receive channel when Omni is on). When Program Mode = Multi the Part 1 receive
channel is used.
2.1.7. Pitch bend
The 7 bits of the MSB are used.
For functions marked "* indicates Program (or Sample) control" in "Control Change" of 3.1.4,
pitch bend can be used for ctrl#.
2.1.8. Channel aftertouch
Received.
For functions marked "* indicates Program (or Sample) control" in "Control Change" of 2.1.4,
channel aftertouch can be used for ctrl#.
MIDI Data Format
data range
0 — 127
0 — 127
0 — 127
0 — 127
0 — 127
data range
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
0 — 127 *
data range
0 — 127
0 — 127
0 — 127
data range
0 — 127
0 — 127
275
Appendix
A5000/A4000 •