Yamaha A4000 Owner's Manual page 183

Cursor q
Cursor
q
Knob 1 Knob 2
Turn
Cursor —
action
Press
EXEC —
action
Knob 1
[ Turn] Cursor
Positions the cursor.
[ Press] EXEC (Execute)
Press this knob to call the backup confirmation display.
Press Knob 5 (YES) to actually execute the backup oper-
ation.
Knob 3
[ Press] RW-ERASE (CD-RW Erase)
Erase all data from a CD-RW disk to allow further record-
ing.
• Depending on the CD-RW drive being used, this pro-
cess may take some time.
Knob 4
[ Turn] CDR DriveID
Selects the drive ID of the CD-R or CD-RW drive to which
the data is to be backed up. When a CD-R or CD-RW
drive is selected, the drive's maker and product number
will be displayed.
[Range] SCSI 0 — SCSI 7
• If a connected CD-R or CD-RW drive cannot be
selected, go to the disk select display (DISK-DISK-
Disk) and check the mount/unmount status and SCSI
ID settings of the device (page 173).
[ Press] TEST
Executes a data transfer test for the selected CD-R or
CD-RW drive. A disk must be loaded in the drive before
the test can be initiated, but no data will be written to the
disk.
• If the test produces an error, choose the next slowest
write speed (Knob 5) and run the test again. The
write speed setting is appropriate if the test produces
no errors. Use the error-free write speed when actu-
ally writing to a disk.
• The data transfer test will take as long as actually
writing to the disk, but since a CD-R disk will become
unusable if an error occurs while actually writing to it,
it is advisable to run the test to check for potential
errors before actually writing the data.
Knob 5
[ Turn] Write Speed
Selects the CD-R/CD-RW write speed.
[Range] x1, x2, x4, x6, x8
Knob 3 Knob 4 Knob 5
— CDR DriveID Write Speed
RW-ERASE TEST EXEC&CONT
[ Press] EXEC&CONT (Execute & Continue)
Press this knob to call the backup confirmation display.
Press Knob 5 (YES) to actually execute the backup oper-
ation.
Cursor w
Cursor
w
Knob 1 Knob 2
Turn
Cursor Backup#
action
Press
EXEC —
action
Knob 1
Same function as Cursor
Knob 2
[ Turn] Backup # (Backup Number)
Selects a line in the disk backup list.
[Range] 1 — 8
• "End of List" will appear at the first line number for
which a disk or volume has not been selected. Line
numbers past the "End of List" line cannot be
selected. For this reason, line numbers 2 and higher
cannot be selected when no disk or volume selec-
tions have been made.
• Disks listed up to the "End of List" line will be backed
up.
Knob 3
Same function as Cursor
Knob 4
[ Turn] Disk
Specifies a disk to be backed up for the currently selected
backup number (Knob 2).
[Range] All connected/mounted disks.
• If a connected SCSI or IDE device (hard disk, ZIP
drive, etc.) cannot be selected, go to the disk select
display (DISK-DISK-Disk) and check the mount/
unmount status and SCSI ID settings of the device
(page 173).
[ Press] TEST
Executes a data transfer test for the selected CD-R or
CD-RW drive. A disk must be loaded in the drive before
the test can be initiated, but no data will be written to the
disk.
• If the test produces an error, choose the next slowest
write speed (Knob 5) and run the test again. The
write speed setting is appropriate if the test produces
no errors. Use the error-free write speed when actu-
ally writing to a disk.
A5000/A4000 •
7. DISK COMMANDS
Knob 3 Knob 4 Knob 5
— Disk —
RW-ERASE TEST EXEC&CONT
q
(page 183).
q
(page 183).
183
Chapter 7 DISK Mode