Yamaha A4000 Owner's Manual page 260

Effect Parameter List
13: RADIO
1 Noise Level 0 — 127
2 Tone 0 — 127
3 Mod LPF Frequency 1.0kHz — 18.0kHz, thru
4 Mod LPF Resonance 1.0 — 12.0
5 HPF Frequency thru,22Hz — 8.0kHz
6 LPF Frequency 1.0kHz — 18.0kHz, thru
7 Dry/Wet Balance D63>W — D=W — D<W63
14: DIGITAL TURNTABLE
1 Click Density 0 — 5
2 Click Level 0 — 127
@3 Noise Tone 0 — 6
4 Noise Mod Speed 0.00Hz — 39.7Hz
5 Noise Mod Depth 0 — 127
6 Dry Send to Noise 0 — 127
7 Noise LPF Freq 1.0kHz — 18.0kHz, thru
8 Noise LPF Q 1.0 — 12.0
9 Noise Level 0 — 127
10 Dry LPF Frequency 1.0kHz — 18.0kHz, thru
11 Dry Level 0 — 127
15: LOFI
1 SamplingFreq Ctrl 44.1kHz — 344Hz
2 Word Length 1 — 127
3 Output Gain -6dB — +36dB
@4 Filter Type thru,PowerBass,Radio,Telephone,Clean,Low
5 PreLPF CutoffFreq 63Hz — 18.0kHz, thru
6 PreLPF Resonance 1 — 12.0
7 Emphasis off/on
8 Bit Assign 0 — 6
9 Input Mode mono/stereo
10 Dry/Wet Balance D63>W — D=W — D<W63
16: LOW PASS FILTER, 17: HIGH PASS FILTER
1 Cutoff Freq 32Hz — 18.0kHz
2 Q 0 — 113
@3 Filter Type -48dB, -24dB
4 Q Type x1, x2
5 Output Gain -12dB — +12dB
Noise may be produced with some voices when the "1. Cutoff Freq" is varied rapidly.
18: BAND PASS FILTER
1 Cutoff Freq 32Hz — 18.0kHz
2 Band Width 1 — 32
3 Q 0 — 113
4 Output Gain -12dB — +12dB
Noise may be produced with some voices when the "1. Cutoff Freq" is varied rapidly.
19: AUTO WAH + DIST, 20: AUTO WAH + OVERDRIVE
1 LFO Frequency 0.0Hz — 39.70Hz
2 LFO Depth 0 — 127
3 Cutoff Freq Offset 0 — 127
4 Resonance 1 — 12.0
5 Drive 0 — 127
6 PostDrive EQ Low -12dB — +12dB
7 PostDrive EQ Mid -12dB — +12dB
8 PostDrive LPF Freq 1.0kHz — 18.0kHz, thru
9 Drive Output Level 0 — 127
10 EQ Low Frequency 32Hz — 2.0kHz
11 EQ Low Gain -12dB — +12dB
12 EQ High Frequency 500Hz — 16.0kHz
13 EQ High Gain -12dB — +12dB
14 Dry/Wet Balance D63>W — D=W — D<W63
21: TOUCH WAH + DIST, 22: TOUCH WAH + OVERDRIVE
1 Sensitive 0 — 127
2 Cutoff Freq Offset 0 — 127
3 Resonance 1 — 12.0
4 Drive 0 — 127
5 PostDrive EQ Low -12dB — +12dB
6 PostDrive EQ Mid -12dB — +12dB
7 PostDrive LPF Freq 1.0kHz — 18.0kHz, thru
8 Drive Output Level 0 — 127
9 EQ Low Frequency 32Hz — 2.0kHz
10 EQ Low Gain -12dB — +12dB
11 EQ High Frequency 500Hz — 16.0kHz
12 EQ High Gain -12dB — +12dB
13 Dry/Wet Balance D63>W — D=W — D<W63
260
Appendix
• A5000/A4000
Degree of noise modulation
Tone of noise modulation
Frequency at which the low pass filter will cut the high range
Resonance of low pass filter
Frequency at which the high pass filter will cut the low range
Frequency at which the low pass filter will cut the high range
Balance between dry sound and effect sound
Frequency with which the click sounds will occur
Level of the click sounds
Tone of noise
Amplitude modulation frequency of the noise
Amplitude modulation depth of the noise
Mixture of dry signal into the noise
Frequency at which the low pass filter will cut the high range
Low pass filter resonance
Noise level
Frequency at which the low pass filter will cut the high range
Level of the dry sound
Selects the sampling frequency
Sets the sound's "roughness"
Output gain
Selects the type of sound
Frequency at which the low pass filter will cut the high range
Adds character to the input low-pass filter
Changes the high-frequency characteristics
Adjusts the effect of the Word Length
Mono/stereo input mode selection
Balance between dry sound and effect sound
Specifies the filter cutoff frequency
Sets the Q
Selects the filter type
Selects the Q type
Output level
Specifies the filter cutoff frequency
Sets the filter bandwidth
Sets the Q
Output level
Frequency at which the wah filter will be controlled
Depth at which the wah filter will be controlled
Offset value for the wah filter control frequency
Bandwidth of the wah filter
(Distortion) Degree of distortion
(Distortion) Gain by which the EQ will boost/cut the low range
(Distortion) Gain by which the EQ will boost/cut the mid range
(Distortion) Frequency at which the filter will cut the high range
(Distortion) Output level
Frequency at which the EQ will boost/cut the low range
Amount of gain by which the EQ will boost/cut the low range
Frequency at which the EQ will boost/cut the high range
Amount of gain by which the EQ will boost/cut the high range
Balance between the dry sound and effect sound
Sensitivity at which the wah filter will change in response to the input level
Offset value for the wah filter control frequency
Bandwidth of the wah filter
(Distortion) Degree of distortion
(Distortion) Gain by which the EQ will boost/cut the low range
(Distortion) Gain by which the EQ will boost/cut the mid range
(Distortion) Frequency at which the filter will cut the high range
(Distortion) Output leve
Frequency at which the EQ will boost/cut the low range
Amount of gain by which the EQ will boost/cut the low range
Frequency at which the EQ will boost/cut the high range
Amount of gain by which the EQ will boost/cut the high range
Balance between the dry sound and effect sound