Hitachi GR2000 Series Configuration Commands page 394

Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2
5.3 Network Interface
Table 5-3
Message
AC name is longer than 32 characters.
Atm not specified.
Aux is not supported.
Bod in ppp configuration not specified.
Bod with group configuration not specified.
Can not be set because there are parameters
other than the interface name in the IP
configuration.
Can not bind interface to Frame Relay since
the interface has already been bound to PPP.
Can not bind interface to PPPoE since the
interface has already been bound to VLAN
Can not bind interface to PPP since the
interface has already been bound to Frame
Relay.
Can not bind interface to VLAN since the
interface has already been bound to PPPOE
Can not delete line with PPPoE configuration
Can not delete PPPoE configuration with IP or
group configuration
Can not change <name>.
Can not change line group name.
Can not change line type.
Can not change subline no.
Can not delete ATM configuration with vp
configuration.
Can not delete bod configuration with
isdn_ppp configuration.
Can not delete bod configuration with ppp
configuration.
Can not delete DLCI configuration referred by
ARP configuration.
Can not delete DLCI configuration referred by
ipx_arp configuration.
Can not delete DLCI configuration referred by
QoS interface configuration.
Can not delete DLCI configuration with IP or
group configuration.
Can not delete Frame Relay configuration
referred by QoS interface configuration.
Can not delete Frame Relay configuration
with dlci configuration.
5-4
Network Interface Error Messages
Contents
The designated AC name is greater than 32 characters. Designate
the AC name with 32 or fewer characters.
ATM is not set. Set a ATM.
Can not set a AUX. AUX is not supported.
Bod in ppp configuration not specified. When ISND PPP is grouped
with PPP, set Bod to PPP in group.
Bod with grouped Isdn PPP configuration not specified.
When ISDN PPP is grouped with PPP, set the same Bod with PPP
within the group to PPP.
Since there are parameters other than interface name in IP
definitions, it is not possible to set EoMPLS L2 transports.
Attempt to built frame relay in interface which has ready been set
PPP. Delete Frame Relay information first, then set PPP.
Attempt made to built PPPoE in interface which has ready been set
VLAN. Delete VLAN information first, then set PPPoE.
Attempt made to built PPP in interface which has ready been set
frame relay. Delete Frame Relay information first, then set PPP.
Attempt made to built VLAN in interface which has ready been set
PPPoE. Delete PPPoE information first, then set VLAN.
PPPoE information is present. Delete the PPPoE information, and
then delete the line.
Attempting to delete the IP "IP information" or PPPoE of the grouped
interface. Delete the IP "IP information" and then delete the PPPoE.
Can not change <name>. To change name, delete the name first and
then set the specified name.
Line group name has already set in line group of different RP
number. Set the line on the same RP.
The line type cannot be changed. To change, delete line type and
add it again.
Can not change subline no. To change name, delete the name first
and then set the specified subline no.
VP information present. Delete VP; delete ATM information.
ISDN PPP information present. Delete ISDN PPP; delete Bod
information.
PPP information present. Delete PPP; delete Bod information.
IP ARP information present. Delete IP ARP; delete DLCI information.
IPX ARP information present. Delete IPX ARP; delete DLCI
information.
QoS interface present. Delete QoS interface; delete DLCI.
Attempt made to delete DLCI of the interface with IP information or
group. Delete IP information or group; delete the DLCI information.
QoS interface present. Delete QoS interface; delete frame relay.
DLCI information present. Delete QoS interface; delete frame relay.
GR2K-GA-0014
Ver. 07-02