Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Toro TX 700
Summary of Contents for Toro TX 700
- Page 1 Form No. 3461-148 Rev A TX 700 Narrow Track Compact Tool Carrier Model No. 22351—Serial No. 400000000 and Up Model No. 22351G—Serial No. 400000000 and Up Model No. 22352—Serial No. 400000000 and Up *3461-148* Register at www.Toro.com. Original Instructions (EN)
- Page 2 Section 4442 or 4443 to use or operate the engine on additional information, contact an Authorized Service any forest-covered, brush-covered, or grass-covered Dealer or Toro Customer Service and have the model land unless the engine is equipped with a spark and serial numbers of your product ready.
-
Page 3: Table Of Contents
Contents Testing the Parking Brake ......... 45 Belt Maintenance ..........46 Checking the Alternator-Belt Tension....46 Safety ............... 4 Controls System Maintenance ......46 General Safety ........... 4 Adjusting the Controls........46 Safety and Instructional Decals ......5 Hydraulic System Maintenance ......47 Product Overview ............11 Hydraulic System Safety........ -
Page 4: Safety
Safety • Do not operate the machine without the guards and other safety protective devices in place and working on the machine. This machine has been designed in accordance with • Keep bystanders and children out of the operating ISO 20474-15:2019. area. -
Page 5: Safety And Instructional Decals
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decalbatterysymbols Battery Symbols decal93-9084 Some or all of these symbols are on your battery. 93-9084 1. - Page 6 decal117-3276 117-3276 1. Engine coolant under 3. Warning—do not touch the pressure hot surface. 2. Explosion hazard—read 4. Warning—read the the Operator's Manual. Operator's Manual. decal125-6694 125–6694 1. Tie down location decal120-0625 120-0625 1. Pinch point, hand—keep hands away. decal125-8483 125-8483 1.
- Page 7 decal130-7637 130-7637 1. Blinking 6. Engine start light—engine-coolant temperature 2. Steady light—engine-oil 7. Parking brake disengaged pressure decal131-8026 3. Blinking light—glow plug 8. Traction neutral 131-8026 9. Auxiliary lever neutral 4. Steady light—battery 1. Battery 3. On warning power—disconnect 5. Hourmeter 2.
- Page 8 decal139-1173 139-1173 1. High-pressure fluid hazard, injection into the body—read the Operator’s Manual before performing maintenance. decal145-3242 145-3242 1. Move forward 3. Move rearward 2. Turn left 4. Turn right decal140-5792 140-5792 1. Read the Operator’s 9. Engine air filter Manual.
- Page 9 decal140-5791 140-5791 1. Fast 5. Engine—start 2. Slow 6. Engine—run 3. Traction disabled 7. Engine—shut off 4. Work light decal145-0637 145-0637 1. Warning—read the Operator's Manual. 7. Cutting/severing hazard of hand or foot—wait for all moving parts to stop before servicing; keep away from moving parts; keep all guards and shields in place.
- Page 10 decal145-0638 145-0638 1. Hydraulic attachment—forward; lock the hydraulic flow using 4. Lower the attachment. the foot pedal. 2. Hydraulic attachment-—reverse; lock the hydraulic flow using 5. Tilt the attachment rearward. the foot pedal. 3. Tilt the attachment forward. 6. Raise the attachment.
-
Page 11: Product Overview
Product Overview g411227 Figure 3 1. Track 6. Auxiliary hydraulic couplers 11. Operator platform 2. Loader arm 7. Hood 12. Parking brake 3. Lift cylinder 8. Lift point 13. Auxiliary hydraulics lock pedal 4. Tie-down/lift loop 9. Fuel gauge 14. Control panel 5. -
Page 12: Controls
Controls Traction-Enable Switch The traction control is automatically disabled when Become familiar with all the controls before you start starting the machine. Toggle the traction-enable the engine and operate the traction unit. switch after starting the machine to use the traction control. - Page 13 Loader Arm/Attachment-Tilt Lever • To turn right, rotate the traction control clockwise. Slowly move the lever to operate the loader arms and tilt the attachment. Note: The detent (float) position allows attachments such as the leveler and the hydraulic blade to follow the contours of the ground (i.e., float) when grading.
- Page 14 Auxiliary-Hydraulics Controls Parking-Brake Lever • To engage the parking brake, rotate the lever to left. Note: The traction unit may roll slightly before the brakes engage in the drive sprocket. • To release the brake, rotate the brake lever to the right.
-
Page 15: Message Display
Message Display Battery-Charge Light If the battery charge becomes too low, the light on Engine-Coolant-Temperature Light the right illuminates steadily. If this happens, shut off the engine and charge or replace the battery. Refer If the engine coolant becomes too hot, the light on Servicing the Battery (page 37). -
Page 16: Specifications
A selection of Toro approved attachments and ensure that the attachment is properly installed accessories is available for use with the machine and that it is a genuine Toro attachment. Read all to enhance and expand its capabilities. Contact the attachment manuals. -
Page 17: Adding Fuel
Fuel Safety Biodiesel Ready • Use extreme care when handling fuel. It is This machine can also use a biodiesel blended fuel flammable and its vapors are explosive. of up to B20 (20% biodiesel, 80% petrodiesel). The petrodiesel portion should be low or ultra low sulfur. •... -
Page 18: Performing Daily Maintenance
• Do not carry a load with the arms raised. Always carry loads close to the ground. • Use only Toro-approved attachments and accessories. Attachments can change the stability and the operating characteristics of the machine. • For machines with a platform: –... - Page 19 • • Slow down and use caution when making turns Slow down and use extra care on hillsides. Ground and crossing roads and sidewalks. Watch for conditions can affect the stability of the machine. traffic. • Avoid starting or stopping on a slope. If the •...
-
Page 20: Starting The Engine
Important: Running the engine at high speeds when the hydraulic system is cold could damage Important: Use only Toro-approved attachments. the hydraulic system. Attachments can change the stability and the operating characteristics of the machine. The warranty of the machine may be voided if you use the machine with unapproved attachments. - Page 21 Position the attachment on a level surface with enough space behind it to accommodate the machine. Start the engine. Tilt the attachment mount plate forward. Position the mount plate into the upper lip of the attachment receiver plate. g003710 Figure 23 1.
-
Page 22: After Operation
Start the engine, tilt the mount plate forward, and CAUTION back the machine away from the attachment. Hydraulic couplers, hydraulic lines/valves, and hydraulic fluid may be hot. If you contact After Operation hot components, you may be burned. • Wear gloves when operating the hydraulic couplers. -
Page 23: Moving A Non-Functioning Machine
Moving a Non-Functioning Hauling the Machine Machine Use a heavy-duty trailer or truck to haul the machine. Use a full-width ramp. Ensure that the trailer or truck Important: Do not tow or pull the machine has all the necessary brakes, lighting, and marking as without first opening the tow valves, or you will required by law. - Page 24 Loading the Machine WARNING Loading or unloading a machine onto a trailer or truck increases the possibility of tip-over and could cause serious injury or death. • Use extreme caution when operating a machine on a ramp. • Load and unload the machine with the heavy end up the ramp.
-
Page 25: Lifting The Machine
Lifting the Machine Remove any attachments and lift the machine using the 4 lift points. Do not exceed a 20-degree angle when lifting the machine; use the minimum chain lengths provided below. g411229 Figure 29 1. Tie-down loops Unloading the Machine Lower the ramp(s). -
Page 26: Maintenance
• Carefully release pressure from components • with stored energy; refer to Relieving Hydraulic Use only genuine Toro replacement parts. Pressure (page 47). • If any maintenance or repair requires the loader • Disconnect the battery before making any repairs;... - Page 27 Maintenance Service Maintenance Procedure Interval • Check the battery condition. Every 50 hours • Check and adjust the track tension. • Check the cooling system hoses. • Check the hydraulic lines for leaks, loose fittings, kinked lines, loose mounting Every 100 hours supports, wear, weather, and chemical deterioration.
-
Page 28: Pre-Maintenance Procedures
Pre-Maintenance Removing and Storing the Cylinder Locks Procedures Important: Remove the cylinder locks from the rods and fully secure them in the storage position Using the Cylinder Locks before operating the machine. Start the engine. WARNING Raise the loader arms to the fully raised position. Shut off the engine and remove the key. - Page 29 Closing the Hood Remove the rear cover. Lift up on the tab securing the prop rod. g367612 Figure 36 1. Hex-washer head 2. Hex-washer head g031216 bolt—3/8 x 1 inch (5) bolt—5/16 x 3/4 inch Figure 34 1. Prop-rod tab Loosen the hose clamp on the hose and disconnect the hose from the cover.
- Page 30 Removing the Front Cover Raise the loader arms and secure with the cylinder locks. Remove the front cover. g365300 Figure 38...
-
Page 31: Lubrication
Lubrication Engine Maintenance Engine Safety Greasing the Machine • Shut off the engine before checking the oil or Service Interval: Before each use or daily (Grease adding oil to the crankcase. immediately after every washing.) • Do not change the engine governor setting or Grease Type: General-purpose grease. -
Page 32: Servicing The Engine Oil
SAE 15W-40 (above 0° F) film, or damage to the rubber seal. Look Note: Toro Premium Engine oil is available from your into the filter while shining a bright light service dealer. See the Parts Catalog or contact an on the outside of the filter; holes in the Authorized Service Dealer for part numbers. - Page 33 Checking the Engine-Oil Level Changing the Engine Oil and Filter Start the engine and let it run for 5 minutes. Park the machine on a level surface, engage the parking brake, and lower the loader arms. Note: This warms the oil so that it drains better. Shut off the engine, remove the key, and allow Park the machine on a level surface.
-
Page 34: Fuel System Maintenance
Fuel System Open the hood. Place a shallow pan or rag under the filter to Maintenance catch oil. Change the oil filter. DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. -
Page 35: Replacing The Water Separator Filter
Replacing the Water Replacing the In-Line Fuel Separator Filter Filter Service Interval: Every 500 hours Service Interval: Every 500 hours Park the machine on a level surface, engage the Park the machine on a level surface, engage the parking brake, and lower the loader arms. parking brake, and lower the loader arms. -
Page 36: Bleeding The Fuel System
Bleeding the Fuel System Electrical System Maintenance You must bleed the fuel system before starting the engine if any of the following situations have occurred: • Initial startup of a new machine Electrical System Safety • The engine has ceased running due to a lack of fuel. -
Page 37: Servicing The Battery
Servicing the Battery Charging the Battery Service Interval: Every 50 hours WARNING Charging the battery produces gasses that Removing the Battery can explode. Never smoke near the battery and keep sparks WARNING and flames away from battery. Incorrect battery cable routing could damage the machine and cables, causing sparks. -
Page 38: Jump-Starting The Machine
For servicing a replacement battery, Coat the battery posts and cable connectors with refer to the battery manufacturer’s instructions. Grafo 112X (skin-over) grease (Toro Part No. 505-47) or petroleum jelly to prevent corrosion. Jump-Starting the Machine Install the battery; refer to... - Page 39 Note: Use properly sized jumper cables with Remove the cables in the reverse order of short lengths to reduce voltage drop between connection. systems. Make sure that the cables are color Close the hood. coded or labeled for the correct polarity. WARNING Batteries contain acid and produce explosive gases.
-
Page 40: Servicing The Fuses
Servicing the Fuses The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or a short. g365804 Figure 53 Fuse Layout (Relay) (Relay) (Relay) (Relay) Key power (20 A) (Relay) (Relay) (Relay) -
Page 41: Drive System Maintenance
Drive System Maintenance Servicing the Tracks Service Interval: After the first 8 hours—Check and adjust the track tension. After the first 50 hours—Check and adjust the track tension. g366284 Every 50 hours—Check and adjust the track Figure 54 tension. 4. Track 1. - Page 42 Replacing the Tracks Loosen the bolts on the rear cover and remove the cover. Removing the Tracks Remove any attachments. Park the machine on a level surface, ensuring that only 1 sprocket half is engaged with the track. g366295 Figure 56 1.
- Page 43 Loosen the jam nut and turn the tensioning Shut off the engine and remove the key. screw to release the tension. Remove the track from the track frame, drive hub, then front wheel. Installing the Tracks Wrap the new track around the front wheel. g363401 Figure 60 1.
-
Page 44: Cooling System Maintenance
Cooling System Apply thread-locking compound to the bolts of the drive sprocket half that you removed and Maintenance install the other sprocket half. Torque the bolts to 80 to 99 N∙m (59 to 73 ft-lb). Cooling System Safety • Swallowing engine coolant can cause poisoning; keep out of reach from children and pets. -
Page 45: Brake Maintenance
Checking the Engine-Coolant Brake Maintenance Level Testing the Parking Brake Service Interval: Before each use or daily—Check the coolant level in the expansion tank. Service Interval: Before each use or daily Engage the parking-brake; refer to The cooling system is filled with a 50/50 solution of Parking-Brake Lever (page 14). -
Page 46: Belt Maintenance
Belt Maintenance Controls System Maintenance Checking the Alternator-Belt Tension Adjusting the Controls Service Interval: Before each use or daily The factory adjusts the controls before shipping the machine. However, after many hours of use, you Every 500 hours (Refer to the engine owner’s may need to adjust the traction control alignment, manual for instructions.) the N... -
Page 47: Hydraulic System Maintenance
• If either of the above Toro fluids are not available, • Keep your body and hands away from pinhole you may use another Universal Tractor leaks or nozzles that eject high-pressure hydraulic Hydraulic Fluid (UTHF), but they must be only fluid. -
Page 48: Checking The Hydraulic-Fluid Level
Checking the If the level is low, add enough fluid to raise it to the proper level. Hydraulic-Fluid Level Install the filler cap. Service Interval: Every 25 hours Lower the bracket. Important: Always use the correct hydraulic fluid. Unspecified fluids will damage the hydraulic Replacing the Hydraulic system. -
Page 49: Changing The Hydraulic Fluid
Cleaning Check the fluid level in the hydraulic tank; refer Hydraulic Fluid Specifications (page 47) add fluid to raise the level to mark on dipstick. Removing Debris Important: Do not overfill the tank. Close the hood. Service Interval: Before each use or daily Important: Operating the engine with blocked Changing the Hydraulic... -
Page 50: Cleaning The Chassis
Cleaning the Chassis Storage Service Interval: Every 100 hours—Check for dirt Storage Safety buildup in the chassis. Over time, the chassis under the engine collects dirt • Shut off the engine, remove the key, wait for all and debris that must be removed. Using a flashlight, moving parts to stop, and allow the machine to open the hood and inspect the area under the engine cool before storing it. -
Page 51: Troubleshooting
Troubleshooting Problem Possible Cause Corrective Action The starter does not crank. 1. The electrical connections are 1. Check the electrical connections for corroded or loose. good contact. 2. A fuse is blown or loose. 2. Correct or replace the fuse. 3. - Page 52 Problem Possible Cause Corrective Action The engine starts but does not keep 1. The fuel-tank vent is restricted. 1. Loosen the cap. If the engine runs with running. the cap loosened, replace the cap. 2. Dirt or water is in the fuel system. 2.
- Page 53 Problem Possible Cause Corrective Action The engine overheats. 1. More coolant is needed. 1. Check and add coolant. 2. There is restricted air flow to the 2. Inspect and clean the radiator screen radiator. with every use. 3. The crankcase-oil level is incorrect. 3.
- Page 54 Problem Possible Cause Corrective Action Exhaust produces excessive white smoke. 1. The key was turned to the S 1. Turn the key to the R position and TART position before the glow-plug light allow the glow-plug light to turn off turned off.
- Page 55 The Toro Company (“Toro”) respects your privacy. When you purchase our products, we may collect certain personal information about you, either directly from you or through your local Toro company or dealer. Toro uses this information to fulfil contractual obligations - such as to register your warranty, process your warranty claim or to contact you in the event of a product recall - and for legitimate business purposes - such as to gauge customer satisfaction, improve our products or provide you with product information which may be of interest.
- Page 56 While the exposure from Toro products may be negligible or well within the “no significant risk” range, out of an abundance of caution, Toro has elected to provide the Prop 65 warnings. Moreover, if Toro does not provide these warnings, it could be sued by the State of California or by private parties seeking to enforce Prop 65 and subject to substantial penalties.