NEC SL2100 Features And Specifications Manual page 790

SL2100
Program
No.
15-03-14 Single Line Telephone Basic Data Setup - For-
warded Caller ID Display Mode
20-03-01 System Options for Single Line Telephones - SLT
Call Waiting Answer Mode
20-03-02 System Options for Single Line Telephones - Ig-
nore Received DP Dial on DTMF SLT Port
20-03-03 System Options for Single Line Telephones - SLT
DTMF Dial to Trunk Lines
20-03-04 System Options for Single Line Telephones - Di-
S
al Sending Start Time for SLT or ARS
20-03-05 System Options for Single Line Telephones - SLT
Operation Mode
20-03-06 System Options for Single Line Telephones -
Headset Ringing Start Time (for SLT)
20-03-07 System Options for Single Line Telephones -
Trunk Call Dial Forced Sending Start Time
(Forced Dial)
20-06-01 Class of Service for Extensions - Class of Serv-
ice for Extensions
20-13-13 Class of Service Options (Supplementary Serv-
ice) - Continued Dialing (DTMF) Signal on ICM
Call
20-15-01 Ring Cycle Setup - Incoming Signal Type : Nor-
mal Incoming Call on Trunk
20-15-03 Ring Cycle Setup - Incoming Signal Type : In-
coming Internal Call
20-15-05 Ring Cycle Setup - Incoming Signal Type :
DID/DDI
80-03-01 DTMF Tone Receiver Setup - Detect Level
80-03-02 DTMF Tone Receiver Setup - Start Delay Time
80-03-03 DTMF Tone Receiver Setup - Min. Detect Level
1-776
Program Name Input Data
0 = Calling Extension Number
(Calling)
1 = External Caller ID (Forward)
0 = Hook Flash (Hooking)
1 = Hook Flash + Service Code
794
0 = Do Not Ignore (No)
1 = Ignore (Yes)
0 = Receive all dialed data, be-
fore sending (All)
1 = Direct through out (Direct)
0 ~ 64800 seconds
0 = Normal Mode
1 = Extended Mode 1
2 = Extended Mode 2
0 ~ 64800 seconds
0 ~ 64800 seconds
1 ~ 15
0 = Off
1 = On
Ringing Cycle Number : 1 ~ 13
Ringing Cycle Number : 1 ~ 13
Ringing Cycle Number : 1 ~ 13
0 = 0 dBm ~ - 25 dBm
1 = - 5 dBm ~ - 30 dBm
2 = - 10 dBm ~ - 35 dBm
3 = - 15 dBm ~ - 40 dBm
4 = - 20 dBm ~ - 45 dBm
5 = - 25 dBm ~ - 50 dBm
6 = - 30 dBm ~ - 55 dBm
0 ~ 255 (0.25 ms ~ 64 ms)
0 ~ 15
DTMF Tone 0 = - 10 dBm (0) to -
25 dBm (15)
DTMF Tone 1 = - 15 dBm (0) to -
30 dBm (15)
DTMF Tone 2 = - 20 dBm (0) to -
35 dBm (15)
DTMF Tone 3 = - 25 dBm (0) to -
40 dBm (15)
DTMF Tone 4 = - 30 dBm (0) to -
45 dBm (15)
DTMF Tone 5 = - 35 dBm (0) to -
50 dBm (15)
DTMF Tone 6 = - 40 dBm (0) to -
55 dBm (15)
Single Line Terminals
ISSUE 1.0
Default
0
0
0
0
1
0
5
0
Extension 101 is Class
15 and other Extension
are Class 1
COS 01 ~ 15 = 1
3
3
8
Refer to the Program-
ming Manual for the
default values.
Refer to the Program-
ming Manual for the
default values.
Refer to the Program-
ming Manual for the
default values.