ABB ACS560 Quick Installation And Start-Up Manual page 19

Motor cable
Motor cable
6. Cut an adequate hole into the rubber grommet. Slide the grommet onto the cable.
6. Cut an adequate hole into the rubber grommet. Slide the grommet onto the cable.
7. Prepare the ends of the input power cable and motor cable as illustrated in the
Motor cable
7. Prepare the ends of the input power cable and motor cable as illustrated in the figure.
figure. If you use aluminum cables, put grease to the peeled aluminum cable
6. Cut an adequate hole into the rubber grommet. Slide the grommet onto the cable.
If you use aluminum cables, put grease on the peeled aluminum cable before connecting
before connecting it to the drive. Two different motor cable types are shown in the
7. Prepare the ends of the input power cable and motor cable as illustrated in the
Motor cable
it to the drive. Two different motor cable types are shown in the figures (7a, 7b).
figures (7a, 7b).
6. Cut an adequate hole into the rubber grommet. Slide the grommet onto the cable.
Note: The bare shield is grounded 360°. Mark the pigtail made from the shield as a PE
Note: The bare shield will be grounded 360 degrees. Mark the pigtail made from
conductor with yellow-and-green color.
7. Prepare the ends of the input power cable and motor cable as illustrated in the
the shield as a PE conductor with yellow-and-green color.
figure. If you use aluminum cables, put grease to the peeled aluminum cable
before connecting it to the drive. Two different motor cable types are shown in the
figures (7a, 7b).
6
Note: The bare shield will be grounded 360 degrees. Mark the pigtail made from
the shield as a PE conductor with yellow-and-green color.
6
7b
7b
PE
8. Slide the cables through the holes of the lead-through plate and attach the
9. Connect the motor cable as follows:
8. Slide the cables through the holes of the lead-through plate and attach the
grommets to the holes (the motor cable to the right and the input power cable to
8. Slide the cables through the holes of the lead-through plate and attach the grommets
the left).
to the holes (the motor cable to the right and the input power cable to the left).
8. Slide the cables through the holes of the lead-through plate and attach the
9. Connect the motor cable as follows:
grommets to the holes (the motor cable to the right and the input power cable to
9. Connect the motor cable as follows:
• Ground the shield 360 degrees under the grounding clamps.
the left).
• Ground the shield 360° under the grounding clamps.
• Connect the twisted shield of the cable to the grounding terminal (9a).
9. Connect the motor cable as follows:
• Connect the phase conductors of the cable to terminals T1/U, T2/V and T3/W.
• Connect the twisted shield of the cable to the grounding terminal (9a).
Tighten the screws to the torque given in the figure (9b).
• Ground the shield 360 degrees under the grounding clamps.
• Connect the phase conductors of the cable to terminals T1/U, T2/V and T3/W.
• Tighten the screws to the torque given in the figure (9b). Connect the twisted shield of the cable to the grounding terminal (9a).
• Connect the phase conductors of the cable to terminals T1/U, T2/V and T3/W.
Note: Frame R8 only:
Tighten the screws to the torque given in the figure (9b).
• If you connected the connector to only one conductor, ABB recommends to put the
conductor under the upper pressure plate.
• The connectors are detachable, but ABB recommends not to detach them. If you
do, detach and reinstall the connectors as follows.
figure. If you use aluminum cables, put grease to the peeled aluminum cable
before connecting it to the drive. Two different motor cable types are shown in the
figures (7a, 7b).
Note: The bare shield will be grounded 360 degrees. Mark the pigtail made from
the shield as a PE conductor with yellow-and-green color.
7a
6
7a 7b
7a 7b
7a
7a 7b
7b
PE
PE
grommets to the holes (the motor cable to the right and the input power cable to
the left).
• Ground the shield 360 degrees under the grounding clamps.
• Connect the twisted shield of the cable to the grounding terminal (9a).
• Connect the phase conductors of the cable to terminals T1/U, T2/V and T3/W.
Tighten the screws to the torque given in the figure (9b).
Electrical installation 87
EN - Quick installation and start-up guide 19
Electrical installation 87
Electrical installation 87
7a
PE
PE
PE
EN
HI