Mitsubishi Electric F700 Instruction Manual page 35

Terminal Terminal
Symbol Name
10E
Frequency
setting power
supply
10
Frequency
2 setting
(voltage)
Frequency
4 setting
(current)
Frequency
1 setting
auxiliary
Frequency
5 setting
common
*1 Set Pr.73, Pr.267, and a voltage/current input switch correctly, then input analog signals in accordance with the settings. Applying a voltage signal
with switch on (current input is selected) or a current signal with switch off (voltage input is selected) could cause component damage of the
inverter or analog circuit of signal output devices. (For details, refer to page 143.)
(2) Output signals
Terminal Terminal
Symbol Name
A1,
Relay output 1
B1,
(alarm output)
C1
A2,
B2, Relay output 2
C2
Description
When connecting the frequency setting potentiometer at an initial
status, connect it to terminal 10.
Change the input specifications of terminal 2 when connecting it
to terminal 10E. (Refer to Pr. 73 Analog input selection in page 146.)
Inputting 0 to 5VDC (or 0 to 10V, 0 to 20mA) provides the
maximum output frequency at 5V (10V, 20mA) and makes input
and output proportional. Use Pr. 73 to switch from among input 0
to 5VDC (initial setting), 0 to 10VDC, and 0 to 20mA.
Set the voltage/current input switch in the ON position to select
current input (0 to 20mA).
*1
Inputting 4 to 20mADC (or 0 to 5V, 0 to 10V) provides the
maximum output frequency at 20mA (5V, 10V) makes input and
output proportional. This input signal is valid only when the AU
signal is on (terminal 2 input is invalid). Use Pr. 267 to switch from
among input 4 to 20mA (initial setting), 0 to 5VDC, and 0 to
10VDC. Set the voltage/current input switch in the OFF position
to select voltage input (0 to 5V/0 to 10V).
Inputting 0 to ±5 VDC or 0 to ±10VDC adds this signal to terminal
2 or 4 frequency setting signal. Use Pr.73 to switch between the
input 0 to ±5VDC and 0 to ±10VDC (initial setting).
Common terminal for frequency setting signal (terminal 2, 1 or 4)
and analog output terminal AM. Do not earth (ground).
Description
1 changeover contact output indicates that the inverter
protective function has activated and the output stopped.
Abnormal: No conduction across B-C (Across A-C Continuity),
Normal: Across B-C Continuity (No conduction across A-C)
1 changeover contact output
Control circuit specifications
Specifications
10VDC±0.4V
Permissible load
current 10mA
5.2VDC±0.2V
Permissible load
current 10mA
Voltage input:
Input resistance
10kΩ ± 1kΩ
Maximum
permissible
voltage 20VDC
Current input:
Input resistance
245Ω ± 5Ω
Maximum
permissible
current 30mA
*1
Switch 1
Switch 2
Input resistance
10kΩ ± 1kΩ
Maximum
permissible voltage
± 20VDC
Specifications
Contact capacity:
230VAC 0.3A
(Power
factor=0.4)
30VDC 0.3A
Rated
Refer to
143
143
143
Voltage/current
input switch
2
4
143
143
--- ------ ------ ----- 143
Rated
Refer to
107
107
27
2