Section 7: Programming Overview; Jumpstart Auto-Programming; 1: Input Points; 2: Output Points - Honeywell Farenhyt IFP-75HV Manual

Addressable fire alarm control panel

Hide thumbs Also See for Farenhyt IFP-75HV:

Installation & operation manual (152 pages)

Table Of Contents

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

Table of Contents

This section of the manual is intended to give you an overview of the programming process. Please read this section of the manual carefully,

especially if you are programming the control panel for the first time.

The JumpStart auto-programming feature automates many programming tasks and selects the default options for the system. You will run the

JumpStart auto-programming at least once when you install the system. See Section 7.1 for details. After you run the JumpStart auto-pro-

gramming, you may need to do some additional programming, depending on your installation. Section 8 of this manual covers manual pro-

grammable options in detail.

Programming the panel can be thought of as a three part process. You must program the following:

•

System options. These are options that affect the general operation of the panel (see Section 8.6 for details).

•

Options for input points and zones. These are primarily options that control the detection behavior of the devices (see Section 8.3 and

Section 8.5 for details).

•

Options for output points and groups. These options include selecting characteristics for output groups and mapping output circuits to

output groups (see Section 8.4 and Section 8.5 for details).

7.1 JumpStart Auto-Programming

The JumpStart auto-programming feature allows for a faster system setup. When you run the JumpStart auto-programming (immediately

after addressing SLC devices), the system scans devices on all SLC loops and determines the device type (for example, photoelectric smoke

detector or heat sensor) and selects some system options based on the device type. This feature saves the installer from having to program

options for each device. Depending on the application, the installer may need to make some changes after the JumpStart auto-programming

completes.

See Section 7.1.3 for complete details about running JumpStart auto-programming.

CAUTION: JUMPSTART AUTO-PROGRAMMING

JUMPSTART AUTO-PROGRAMMING IS INTENDED TO BE RUN ONE TIME ONLY, IMMEDIATELY AFTER SLC DEVICES

HAVE BEEN ADDRESSED AND CONNECTED. JUMPSTART AUTO-PROGRAMMING WILL RESET ALL MANUALLY

PROGRAMMED OPTIONS TO DEFAULT SETTINGS. DO NOT RUN JUMPSTART AFTER YOU HAVE CONFIGURED THE

SYSTEM

7.1.1 Input Points

JumpStart auto-programming will determine the number and type of input points (detectors or contact monitor modules) on each SLC loop.

JumpStart auto-programming assigns the correct detector type (heat, or photoelectric), so the installer does not need to edit device type for

detectors. Any contact monitor modules on the system will be assigned type "Manual Pull." The installer will need to manually change the

switch type if manual pull is not correct.

JumpStart auto-programming creates one zone (Zone 1) and assigns all input points to Zone 1. Zone 1 is mapped to Output Group 1.

7.1.2 Output Points

The JumpStart auto-programming creates three output groups and assigns output circuits as follows:

Configured as Notification and assigned to Group 1. JumpStart auto-programming automatically programs Zone 1 to activate

Circuits 1-2

Group 1 using constant on output when an alarm condition occurs.

Circuit 3 (Relay 1)

stant on output when a supervisory condition occurs.

Circuit 4 (Relay 2)

stant on output when an alarm occurs.

Addressable output points (Relay modules)

point) and assigned to Group 1.

NOTE: The Relay output is constant even if the zone activating the relay is programmed with an output pattern.

7.1.3 Running JumpStart Auto-Programming

Run JumpStart auto-programming immediately after you address and connect all the input devices (detectors, pull stations, and so on) and

output devices (notification appliances, relays, and so on).

NOTE: To install a few devices manually after running JumpStart, see Section 8.2.2.

To run JumpStart auto-programming:

Select 7 for the Program Menu.

From the next Menu, select 6 for JumpStart.

When the message, "SLC FAMILY" message appears, select IDP, SK, or SD, depending on the type of SLC devices the panel is using,

and press ENTER to accept.

A series of messages display for the next several seconds. JumpStart scans the SLC loops for the devices. This process can take several

minutes, depending on the number of devices attached.

When the message "Configuring System Done" displays, press any key to continue.

IFP-75 Series Manual — P/N LS10147-001SK-E:E 4/6/2022