Makita UT001G Instruction Manual page 10

Operation of speed change knob
NOTICE:
Use the speed change knob only after
the tool comes to a complete stop. Changing the
tool speed mode before the tool stops may damage
the tool.
NOTICE:
Always set the speed change knob
carefully into the correct position. If you operate
the tool with the speed change knob positioned half-
way between the position 1 and the position 2, the
tool may be damaged.
NOTICE:
If the rotation speed significantly
decreases during operation in the high speed
mode, stop the tool and change the mode to the
low speed mode. Otherwise, the motor may get
overloaded and cause a malfunction or fire.
Two speed ranges can be preselected with the speed
change knob.
Select the proper speed mode for the material to be
mixed.
To change the speed mode, turn the speed change
knob so that the pointer points to the dot at position
1 for low speed mode or the dot at position 2 for high
speed mode.
► Fig.16: 1. Pointer 2. Speed change knob 3. Dot
Operation of speed adjusting dial
The tool speed can be adjusted steplessly by turning
the speed adjusting dial. The no load speed when the
switch trigger is fully pulled can be adjusted 270 min
-1
to 500 min at low speed mode, 500 min
at high speed mode. Higher speed is obtained when
the dial is turned in the direction of number 5; lower
speed is obtained when it is turned in the direction of
number 1.
Select the proper speed for the material to be mixed.
► Fig.17: 1. Speed adjusting dial
NOTICE:
The speed adjusting dial can be turned
only as far as 5 and back to 1. Do not force it past
5 or 1.
Accidental restart preventive
function
If you install the battery cartridge while pulling the
switch trigger or locking the switch trigger, the tool does
not start. To start the tool, release the switch trigger, and
then pull the switch trigger.
Electronic function
The tool is equipped with the following electronic func-
tion for easy operation.
Soft start
The soft-start function minimizes start-up shock, and
makes the tool start smoothly.
Basic operations
operate the tool around flammable materials such
as paint with thinner used as solvent. Failure to do
so may cause an injury.
in the high speed mode. You may lose the control of
the tool and cause an injury.
outside the stirring vessel.
during use, turn off the switch and stop using the
tool.
NOTICE:
mixing blade floating out of the material, be care-
ful not to splash the material.
NOTICE:
other than stirring mortar, concrete, etc.
1.
according to the material to be mixed.
2.
ing blade under material fully. Check that the material is
not solidified and the safety of the work site, then turn
on the tool.
3.
ing operation so that whole part of material can be mixed.
-1
4.
-1 -1
to 920 min that the mixing blade has come to a complete stop, and
then pull it out of the mixing container.
Applied operations
switched off and the battery cartridge is removed
before adjusting or checking function on the tool.
Installing or removing the shaft holder
country specific
For UT001G
Install one of the shaft holders optionally available to fit
your screw size of the shaft.
► Fig.18: 1. M12 shaft holder 2. M14 shaft holder
While holding the spindle with a wrench, loosen the
shaft holder with another wrench.
► Fig.19: 1. Shaft holder 2. Wrench 3. Spindle
To install the shaft holder, perform the removal proce-
dure in reverse.
For UT002G
1.
loosen the chuck with the hex wrench while holding the
spindle with the wrench.
► Fig.20: 1. Hex wrench 2. Chuck 3. Wrench 4. Spindle
2.
ing the spindle with another wrench.
► Fig.21: 1. Shaft holder 2. Wrench 3. Spindle
10 ENGLISH
CAUTION:
Do not mix flammable materials or
CAUTION:
Do not mix high viscosity material
CAUTION:
Do not rotate the mixing blade
CAUTION:
If you hear an abnormal noise
When you mix the material while the
Do not use the tool for any purpose
Select high speed mode or low speed mode
Hold the tool firmly with both hands. Place the mix-
Move the mixing blade up and down during the mix-
When finishing mixing, turn off the tool. Make sure
CAUTION:
Always be sure that the tool is
Insert the hex wrench into the chuck, and then
Tighten the shaft holder with a wrench while hold-