Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Makita UT001GM102
Summary of Contents for Makita UT001GM102
- Page 1 INSTRUCTION MANUAL Cordless Mixer UT001G UT002G Read before use.
-
Page 2: Specifications
SPECIFICATIONS Model: UT001G UT002G No load speed High speed mode 0 - 920 min Low speed mode 0 - 500 min Maximum mixing blade diameter 240 mm Overall length (without shaft with battery cover S 373 mm 363 mm and mixing blade) with battery cover L 412 mm 403 mm... -
Page 3: Ec Declaration Of Conformity
SAFETY WARNINGS WARNING: Wear ear protection. WARNING: The noise emission during actual use of the power tool can differ from the declared General power tool safety warnings value(s) depending on the ways in which the tool is used especially what kind of workpiece is WARNING: processed. - Page 4 Personal safety Power tool use and care Stay alert, watch what you are doing and use Do not force the power tool. Use the correct common sense when operating a power tool. power tool for your application. The correct power tool will do the job better and safer at the Do not use a power tool while you are tired or under the influence of drugs, alcohol or med- rate for which it was designed.
- Page 5 12. Hold the tool firmly. Do not use a battery pack or tool that is dam- aged or modified. Damaged or modified batteries 13. Keep hands away from rotating parts. may exhibit unpredictable behaviour resulting in 14. Do not leave the tool running. Operate the tool fire, explosion or risk of injury.
-
Page 6: Parts Description
Use of non-genuine Makita batteries, or batteries that Lock-off button have been altered, may result in the battery bursting Switch trigger causing fires, personal injury and damage. It will Speed adjusting dial Lock button also void the Makita warranty for the Makita tool and Speed change knob Battery cover charger. Handle Chuck Tips for maintaining maximum... -
Page 7: Preparation Before Use
Things you need to know before use PREPARATION BEFORE USE Hold the handle when using or carrying the tool. Indicating the remaining battery capacity Press the check button on the battery cartridge to indi- cate the remaining battery capacity. The indicator lamps light up for a few seconds. -
Page 8: How To Use
Hold the flats on the shaft holder with wrench 19 HOW TO USE so that the shaft holder cannot revolve. With the flats held so, tighten the hex nut with another wrench 19 in the direction of arrow. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. NOTICE: When you are not working, lay the machine down and store it. -
Page 9: Installing Or Removing Battery Cartridge
Fig.12 ► 1 . Hex bolt 2. Shaft 3. Flat surface 4. Mixing blade NOTE: Ask your local Makita Service Center about which is mixing blades are allowed. 9 ENGLISH... - Page 10 NEVER use the tool if it runs when you simply pull the switch trigger without pressing the lock-off button. A switch in need of repair may result in unintentional operation and serious personal injury. Return tool to a Makita service center for proper repairs BEFORE further usage. Fig.16 WARNING: Do not install the battery cartridge ► 1 .
- Page 11 Operation of speed adjusting dial Basic operations The tool speed can be adjusted steplessly by turning Do not mix flammable materials or CAUTION: the speed adjusting dial. The no load speed when the operate the tool around flammable materials such switch trigger is fully pulled can be adjusted 270 min as paint with thinner used as solvent. Failure to do to 500 min at low speed mode, 500 min to 920 min so may cause an injury.
- Page 12 Open the standard equipped battery cover while Installing or removing the shaft pressing the button on the battery cover. holder Loosen the screw securing the standard equipped country specific battery cover. Then remove the screw, sleeve and the battery cover. For UT001G Install one of the shaft holders optionally available to fit your screw size of the shaft.
-
Page 13: Optional Accessories
ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. - Page 16 Jan-Baptist Vinkstraat 2, Makita Europe N.V. 3070 Kortenberg, Belgium 3-11-8, Sumiyoshi-cho, Makita Corporation Anjo, Aichi 446-8502 Japan 885997-228 www.makita.com 20220802...