Mounting The Breakout Box For T1 Pri And E1 Cisco Unified Meetingplace Systems - Cisco 700 MHz Installation And Upgrade Manual
Audio server
Hide thumbs
Also See for 700 MHz:
- Configuration manual (87 pages) ,
- Administration manual (36 pages) ,
- Getting started manual (27 pages)
Table of Contents
Advertisement
Chapter 2
Installing the Cisco Unified MeetingPlace 8100 Series Hardware
Figure 2-4
Mounting the Breakout Box for T1 PRI and E1 Cisco Unified MeetingPlace
Systems
If the Cisco Unified MeetingPlace system does not require a breakout box (T1 PRI or E1 configuration),
Note
skip to the
page
The breakout box provides a standard RJ-45 telephony interface. The breakout box interfaces to a
maximum of 16 cables with an MP-MA-16-PRI and a maximum of 4 cables with each MP-MA-4-PRI.
Cisco Systems ships the necessary number of RJ-48c cables to connect each breakout box to your PBX
or Telco NIU with each Multi Access Blade.
In some cases, the RJ-48c cables provided by Cisco Systems may not be appropriate for your PBX or
Note
NIU side connections. If this is the case, create your own custom cables, which require an RJ-48c
connector on the breakout box side. (For custom-cable requirements, see the
Requirements for Cisco Unified MeetingPlace Systems" section on page
Cisco Systems also ships the necessary number of 50-pin Amphenol cables with the breakout box: two
50-pin Amphenol cables to connect each MP-MA-16-PRI to the breakout box and one 50-pin Amphenol
cable to connect each MP-MA-4-PRI to the breakout box.
If the Cisco Unified MeetingPlace system requires two MP-MA-16-PRIs, you need two breakout boxes.
(A fully loaded 960-port E1 Cisco Unified MeetingPlace system and a fully loaded 736-port T1 PRI
Cisco Unified MeetingPlace system have two MP-MA-16-PRIs.)
Only the Cisco Unified MeetingPlace 8112 can have two breakout boxes.
Note
OL-13417-01
Mounting the Cisco Unified MeetingPlace 8112 into an EIA Equipment Rack
Rack-mounting
OUT OF
SERVI CE
OUT OF
SERVI CE
OUT OF
OUT OF
OUT OF
SERVI CE
OUT OF
SERVI CE
SERVI CE
OUT OF
SERVI CE
OUT OF
SERVI CE
OUT OF
SERVI CE
OUT OF
1
SERVI CE
OUT OF
2
SERVI CE
OUT OF
SERVI CE
OUT OF
SERVI CE
OUT OF
OUT OF
3
SERVI CE
OUT OF
SERVI CE
4
SERVI CE
OUT OF
5
SERVI CE
OUT OF
SERVI CE
OUT OF
SERVI CE
OUT OF
6
OUT OF
SERVI CE
OUT OF
7
SERVI CE
SERVI CE
OUT OF
8
SERVI CE
OUT OF
SERVI CE
OUT OF
SERVI CE
OUT OF
9
SERVI CE
OUT OF
10
SERVI CE
OUT OF
SERVI CE
OUT OF
SERVI CE
OUT OF
11
SERVI CE
OUT OF
SERVI CE
12
13
SERVI CE
OUT OF
SERVI CE
14
15
16
1
2
3
4
5
6
7
8
PWR ON
1
PWR OFF
2
1
1
2
1
2
1
2
2
9
10
1
11
1
2
1
12
2
1
2
13
1
3
2
3
2
14
4
3
4
15
3
4
4
1
16
2
3
4
"Connecting the Power Cable to the Cisco Unified MeetingPlace 8100 Series" section on
2-11.
Installation and Upgrade Guide for Cisco Unified MeetingPlace Audio Server 6.x
Mounting the Cisco Unified MeetingPlace 8100 Series
holes
"E1 Digital Trunk
1-10.)
2-7
Advertisement
Table of Contents
Troubleshooting
