Advertisement
Connect Cables Turn On Power Verify Status for Versions 6.3 - 6.4
about management interfaces, see the
about network topology, see the
Each management center-supported SFP+ transceiver (SFP-10G-SR and SFP-10G-LR) has an internal serial
EEPROM that is encoded with security information. This encoding allows us to identify and validate that the
SFP transceiver meets the requirements for the chassis.
Note
Step 4
(Optional) eth3 management interface —Install any management center-supported SFP+ transceiver and cable
in this 10-Gigabit Ethernet SFP+ interface as needed. You can connect this interfaces to the same or different
network from your other management interfaces depending on your network needs. For more information
about management interfaces, see the
about network topology, see the
Each management center-supported SFP+ transceiver (SFP-10G-SR and SFP-10G-LR) has an internal serial
EEPROM that is encoded with security information. This encoding allows us to identify and validate that the
SFP transceiver meets the requirements for the chassis.
Note
Step 5
(Optional) USB port —Connect a keyboard to the USB port.
You can use this connection and a monitor that is connected to the VGA port to configure network settings
for the management center before performing initial setup using the web interface; see
Network Settings Using a Physical Connection for Software Versions 6.3 - 6.4, on page
Step 6
(Optional) VGA port —Connect a monitor to the VGA port.
The management center sends console messages to the VGA port by default. You can use this connection and
a keyboard connected to a USB port to configure network settings for the management center before performing
initial setup using the web interface; see
for Software Versions 6.3 - 6.4, on page
Step 7
(Optional) Use the RJ-45 to DB-9 console cable supplied with the appliance (Cisco part number 72-3383-XX)
to connect a local computer to the management center serial port. (You may need a DB-9-to-USB adaptor to
connect to the local computer.) You can use this connection for serial access (see
page
40) and to configure network settings for the management center before performing initial setup using
the web interface; see
Versions 6.3 - 6.4, on page
Step 8
(Optional) Use an ethernet cable to connect the CIMC port to a local network reachable from a computer
where you run an IPMI utility for Lights-Out Management. See
for more information.
Step 9
Power supply—Use one of the supported power cords to connect the power supplies of the chassis to your
power source. For more information about supported power cords, see the
Center 1600, 2600, and 4600 Hardware Installation
Note
Step 10
Power—Press the Power button on the front of the chassis, and verify that the power status LED is on.
Cisco Firepower Management Center 1600, 2600, and 4600 Getting Started Guide
24
Cisco Secure Firewall Management Center Device Configuration
Only management center-supported SFP+ transceivers are compatible with the 10-Gb interfaces.
Cisco TAC may refuse support for any interoperability problems that result from using an untested
third-party SFP transceiver.
Cisco Secure Firewall Management Center Device Configuration
Only management center-supported SFP+ transceivers are compatible with the 10-Gb interfaces.
Cisco TAC may refuse support for any interoperability problems that result from using an untested
third-party SFP transceiver.
(Optional) Configure Network Settings Using a Physical Connection for Software
25.
We recommend connecting both power supplies on the management center to provide redundancy
protection. The appliance generates a health alert if only one power supply is connected.
Firepower Management Center 1600, 2600, and 4600 Getting Started Guide
Cisco Secure Firewall Management Center Administration Guide
Cisco Secure Firewall Management Center Administration Guide
(Optional) Configure Network Settings Using a Physical Connection
25.
Set Up Lights-Out Management, on page 41
Guide.
Guide.
Guide.
(Optional) Configure
25.
Set Up Serial Access, on
Cisco Firepower Management
and
and
Advertisement
