Node Default Settings; Table C-5 Node Default Settings - Cisco ONS 15600 Reference Manual

Appendix C Network Element Defaults
Table C-4 ASAP Card Default Settings (continued)
Default Name
ASAP_4.OC48-PORT.pmthresholds.sts1.nearend.1day.NPJC-PGEN
ASAP_4.OC48-PORT.pmthresholds.sts1.nearend.1day.PPJC-PDET
ASAP_4.OC48-PORT.pmthresholds.sts1.nearend.1day.PPJC-PGEN
ASAP_4.OC48-PORT.pmthresholds.sts1.nearend.1day.SES
ASAP_4.OC48-PORT.pmthresholds.sts1.nearend.1day.UAS
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.15min.CV
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.15min.ES
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.15min.FC
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.15min.SES
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.15min.UAS
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.1day.CV
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.1day.ES
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.1day.FC
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.1day.SES
ASAP_4.OC48-PORT.pmthresholds.sts12c+.farend.1day.UAS
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.15min.CV
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.15min.ES
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.15min.FC
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.15min.NPJC-PDET
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.15min.NPJC-PGEN
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.15min.PPJC-PDET
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.15min.PPJC-PGEN
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.15min.SES
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.15min.UAS
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.1day.CV
ASAP_4.OC48-PORT.pmthresholds.sts12c+.nearend.1day.ES
C.3 Node Default Settings
Table C-5 on page C-39
the following user-configurable defaults for each Cisco ONS 15600 node:
•
•
lists the node-level default settings for the Cisco ONS 15600. Cisco provides
Circuit settings—Set the administrative state andpath protection circuit defaults.
General settings—Set general node management defaults, including whether to use Daylight
Savings Time (DST), the IP address of the Network Time Protocol/Simple Network Time Protocol
(NTP/SNTP) server to be used, the time zone where the node is located, the signal degrade (SD)
path bit error rate (BER) value, the defaults description, whether automatic autonomous Transcation
C.3 Node Default Settings
Default Value Default Domain
5760 (count) 0 - 691200000
5760 (count) 0 - 691200000
5760 (count) 0 - 691200000
7 (seconds) 0 - 86400
10 (seconds) 0 - 86400
75 (B3 count) 0 - 2160000
60 (seconds) 0 - 900
10 (count) 0 - 72
3 (seconds) 0 - 900
10 (seconds) 0 - 900
750 (B3 0 - 207360000
count)
600 (seconds) 0 - 86400
40 (count) 0 - 6912
7 (seconds) 0 - 86400
10 (seconds) 0 - 86400
75 (B3 count) 0 - 2160000
60 (seconds) 0 - 900
10 (count) 0 - 72
60 (count) 0 - 7200000
60 (count) 0 - 7200000
60 (count) 0 - 7200000
60 (count) 0 - 7200000
3 (seconds) 0 - 900
10 (seconds) 0 - 900
750 (B3 0 - 207360000
count)
600 (seconds) 0 - 86400
Cisco ONS 15600 Reference Manual, R8.0
C-37