Honeywell rapid eye System Administrator Manual page 15

Fig. 8–6.
Fig. 8–7.
Fig. 8–8.
Fig. 8–9.
Fig. 8–10. Some Devices can Be Searched for Data such as "No Sale".
Fig. 8–11. Cash Registers, Connected to a Honeywell PIT.
Fig. 8–12. A NetPIT Device on PORT 3, Showing All Serial Interface Values.
Fig. 8–13. Expanded NetPIT device on PORT 3, showing three POS devices.
Fig. 8–14. Audio Tab.
Fig. 9–1.
Fig. 9–2.
Fig. 9–3.
Fig. 10–1. Logging on to SQL-Server Differs from the Log on to Admin.
Fig. 10–2. System Password.
Fig. 10–3. Securing a Unit.
Fig. 10–4. After Removing a System Password.
Fig. 10–5. The LVP Utility Is Used only when a Unit Replaces another at a Secured Site.
Fig. 10–6. Inputting a Previous Owner's System Password into the LVP Utility.
Fig. 10–7. Assigning Rights to a "Night Operator" Multi-Media Account.
Fig. 10–8. Summary of a User's Rights on the Users Tab.
Fig. 10–9. Account's Limit on Session Time, before Needing to Reconnect.
Fig. 10–10. Limiting an Account's Use of Cameras at a Site.
Fig. 10–11. Identifying a Camera that is Not Recording, in a Live Session.
Fig. 10–12. Overriding a Camera that is not Recording, Using Event Recording.
Fig. 10–13. Sources of Events Include the Unit itself.
Fig. 10–14. Once Acknowledged, Alarms Are Entered into the Multi Db.
Fig. 10–15. A Multi-Media Unit Can Log an Event without Sounding an Alarm.
Fig. 10–16. Events Caused by a Multi-Media Unit or a View Operator.
Fig. 10–17. Search for Events Window.
Fig. 10–18. A Multi-Media Unit Can Be Set to Send Alarms to Specific PCs.
Fig. 10–19. Denying Access (1) and Updating Security for each Site in the Account (2).
Fig. 11–1. A Multi-Media Unit Can Send Alarms to a Specific PC.
Fig. 11–2. Over a Network, Alarm's Are Sent to an Alarm Station's IP Address.
Fig. 11–3. Receiving Alarms from a Multi-Media Unit, over a WAN or the Internet.
Fig. 11–4. Connecting through a WAN to a Multi-Media Alarm Station on a LAN.
Fig. 11–5. To Report an Alarm, a Multi-Media Unit Can Call an Alarm Station.
Fig. 11–6. Area Code Input Is Needed to Reach a Multi-Media Alarm Station.
Fig. 11–7. Connection for an Alarm Station (1) Is Shown also in a Site's Definition (2).
Fig. 11–8. Irregular Use of Area Codes when Units Are Calling an Alarm Station.
Fig. 11–9. Customizing the Dial-up to an Alarm Station in the Site's Definition.
Fig. 11–10. International Prefixes for Use of Rapid Eye Software in North America.
Fig. 11–11. International Prefixes for Use of Dial-up in Rapid Eye Software.
Fig. 11–12. A Multi-Media Unit Can Send Alarms through a RAS Server.
Fig. 11–13. RAS Configuration.
Fig. 12–1. Adding a Tour Name.
Fig. 12–2. The Default Amount of Time for a Tour of each Unit.
Fig. 12–3. Customizing the Amount of Time that a Multi-Media Unit Is Toured.
Fig. 13–1. Alarm Log.
Document 800-02325 Rev A
07/08
Enabling the FAULT RELAY Changes the Name of Output6.
Serial Devices Tab Showing "Internal Port–Modem" Data.
Monitor Out Tab, for a Multi-Media Unit's MONITOR OUTPUT 1.
Customer Devices can Include POS Units, such as Cash Registers.
Button for Changing User Management from Local to Central.
Adding a "Night Operator" Account.
Defaults: User Account Rights (1) and Site Access (2).
System Administrator Guide
137
140
144
145
146
148
148
149
150
158
160
163
171
172
173
175
179
181
184
185
189
190
191
192
193
194
195
198
199
201
203
207
211
212
213
214
215
216
217
218
220
221
222
222
228
229
230
233
15