Toshiba Strata CTX Programming Manual page 336

Telephone Button Programming
300 Series Programs
Programs 303~315
Button Sequence
308-01 Auto Release
, n, ,
A7 C‚yq
308-02 Short Flash
, n, ,
A7! C‚yq
308-03 Long Flash
, n,
A7" C‚yq
308-04 Pause after Flash
, n,
A7# C‚yq
308-04 Response Timer
, n,
A7$ C‚yq
309 Direct Inward Dialing
,
"( C‚yq
309-00 ILG Number
n,
C‚yq
309-01 DID Number
, n,
A7 C‚yq
309-02 MOH Source
, n,
A7! C‚yq
309-03 GCO Key Group
, n,
A7" C‚yq
309-04 Pool Key Group
, n,
A7# C‚yq
13-58
(continued)
Value(s)
n = 1. Disable
2. Detect 95ms
3. Detect 450ms (default)
n = 0~15, where 1 = 100msec.
(default = 5, which is .5
seconds)
0 = no flash
n = 0, 5, 10, 15, 20, 25 and 30,
where 5 = .5 seconds.
(default = 20)
n = 0~5, 0 = immediately sent,
and 1sec.delay to
5sec.delay
(default = 1 second delay
before sending digits)
n = 0~3000
n = 1~32 (CTX100)
1~50 (CTX670 Basic)
1~128 (CTX670 Exp.)
n = 1~7 digits may include wild
card "?" where "?" = 0~9
n = 1. Quiet Tone
2. External 1 (default)
3. External 2
4. External 3
5. External 4
6. External 5
7. External 6
8. External 7
9. External 8
10. External 9
11. External 10
12. External 11
13. External 12
14. External 13
15. External 14
16. External 15
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
(default = 0)
n = 0~32 (CTX100)
0~50 (CTX670 Basic)
0~128 (CTX670 Exp.)
(default = 0)
Select the Automatic Release timing.
Note Select Disable if the CO does not send the automatic release
signal to the loop start trunk.
Select Short Flash Time. When a telephone initiates the short flash
signal to the CO line it is connected to (using the short Flash feature
button or access code #450) the duration of a short flash is
determined by this command. Normally this signal is used to hook
flash a centrex line. The short flash range is 0 to 1.5 seconds in
increments of 0.1 seconds.
Select Long Flash Time. When a telephone initiates the long flash
signal to the CO line it is connected to (using the Long Flash feature
button or access code #451) the duration of a long flash is determined
by this command. Normally this signal is used to disconnect the line.
The long flash range is 0 to 3 seconds in increments of 0.5 seconds.
Pause time after flash: After a flash signal is sent to a CO line, this
timer determines when the line will start to send the dialed digits to
the other end.
The response timer is for analog DID/TIE lines that have the "start
method" set for "Timing" in Program 300-06. After a line is seized this
timer determines when the line will start to send the dialed digits to
the other end.
Possible Values 0=immediatly sent, and 50msec.delay to
500msec.delay. (default=500mseconds delay before sending digits).
This command assigns DID Number Analysis Table to ILG.
Select the ILG number.
Enter a DID number.
Set Music On Hold for Analog ISDN DID Trunk
GCO Key Group number.
Pooled Line Key Group
Strata CTX Programming - Part 3:Telephone Button Programming 04/03
Summary