Sharp IV-S30J User Manual page 264

Computer Link
*1 When the termination code is 08
appended information. (Example: 0A
*2 Measurement number when outputting the results
00 = Measurement 0, Camera 1, 01
(H)
03 = Measurement 2, 04
(H)
*3 Result output (Y0 to Y15)
Bit
Y15 Y14 Y13 Y12 Y11 Y10 Y9 Y8
*4 Measurement program for measurement 0
00 = none, 01
(H)
*5 Measurement programs for measurements 1 to 4
00 = none, 01
(H)
lead inspection, 05
conversion, 07
multiple position measurement, 0A
*6 Output data from measurements 0 to 4 (block 0)
The data output will vary according to whether "ANY" or "BLOCK-ASSIGN" was selected on the
SERIAL OUTPUT item. - Pages 16-23 to 16-27.
When a block is specified
- The measurement data from measurement numbers 0 to 4 in block 0 is output. (Max. 496 bytes).
- Measurement numbers that have not been specified will not output any data. (The space will be
filled by the next item. Max. 500 bytes.)
- See pages 18-6 to 18-13, for details about the measurement data in block 0.
When "ANY" is selected for the output
See page 18-16.
*7 Assigned block data
When the SERIAL OUTPUT item is set to "BLOCK-ASSIGN," the IV-S30J will output the
measurement result data in the specified block number. When the SERIAL OUTPUT item is set
to "ANY," the nature of the output will depend on the output settings.
For details about how to specify measurement output, see pages 16-23 and 16-25.
- No data is output if block 0 (00) is specified.
For details about the measurement data block, see pages 18-5 to 18-15.
- The top address where the specified block of data is written will be an address made by
adding 512 bytes to the top address for writing results.
Top address
for writing
results
18
Top address
for writing
results
+ 512 bytes
(H)
= Measurement 3, 05
(H)
H (09005)
7 6 5 4 3 2 1 0
= positional deviation measurement
(H)
= positional deviation measurement, 02
(H)
= area measurement by binary conversion, 06
(H)
= object identification by binary conversion, 08
(H)
Sharp Mitsubishi
09000
D0000
09001
. .
. .
. .
.
.
.
.
.
.
. .
. .
. .
19000
D0256
19001
. .
. .
. .
(received an error response), the error code is contained in the
on a Sharp PC = parity error)
(H)
= Measurement 0, Camera 2, 02
(H)
= Measurement 4
(H)
L (09004)
7 6 5 4 3 2 1 0
Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0
(H)
= multiple degree of match inspections
(H)
Yokogawa
OMRON
L L
L
DM0000 D00001
H H
H
. .
. .
. .
L L
L
. .
. .
H H
H
. .
. .
. .
L L
L
DM0256
D00256
H H
H
.
.
.
.
.
.
18-4
= Measurement 1,
(H)
= degree of match inspection, 03
= object counting by binary
(H)
= point measurement, 09
(H)
Contents
Termination code
Appended information
.
.
.
Output data from
.
measurement 4 (block 0)
.
.
.
Assigned block data
.
.
.
.
=
(H)
=
(H)