Table of Contents
Advertisement
12. OTHER INFORMATION
O
Troubleshooting
Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing.
Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation.
Symptom
The Power does not turn On.
The unit does not respond.
No Picture, Sound or Menu
appears on the screen.
Time jumps/Auto Clock has
incorrect Time.
The unit does not operate
properly.
"Repairing" appears on the TV
screen.
In case you intend to Cancel the
Repairing Process.
The Clock Display does not appear
on the Front Panel Display.
When you forget the Password for
Parental Lock.
EN - 66
O
O
Remedy
• Check that the AC Power cord is connected securely.
• Remote Control batteries may be weak, replace them with new ones.
• Check operation of the Remote Control, refer to Page 4.
• After "Initialize for Personal Information", this unit's Remote Control
Code will be set back to the default setting "Code1". Keep pressing
[ OK ] and press the number button [ 1 ] on the Remote Control to set
the Remote Control's Remote Control Code to "Code1". (Refer to
page 58 on 'Remote Control'.)
• Press and hold the [
more than 8 seconds to turn the unit Off, then Unplug the unit and
leave the unit unplugged for a while (or leave the unit plugged in and
press the recessed RESET button on the Rear Cabinet), then plug in
the unit. If the unit does not Power On please contact our Customer
Service Center for Service on the model.
• "
" or error message appears if the operation is prohibited.
• Remote Control batteries may be weak, replace them with new ones.
• Check operation of the Remote Control, refer to Page 4.
• Press and hold the [
8 seconds to turn the unit Off, then Unplug the unit and leave the unit unplugged
for a while (or leave the unit plugged in and press the recessed RESET button
on the Rear Cabinet), then plug in the unit. If the unit does not Power On please
contact our Customer Service Center for Service on the model.
• Depending on the Source/Connection, confirm the following:
– For Digital Antenna/basic Digital Cable, redo Auto Scan on the Unit.
– For Satellite Receiver/Digital Cable Box, check the Connections to
make sure they are securely connected.
– For RF Coaxial Cable, redo Auto Scan on the Unit.
– For HDMI and RCA Video/Audio, check the Connections to make
sure they are securely connected.
• Check if the Connections are made securely and correctly.
• Check if the Cables are damaged.
• Check if a correct External Input Channel is Selected on your TV. (Refer to page 26)
• Check if you have completed the Channel setting. (Refer to page 60)
• Set the 'Auto Clock Setting' to "Off" and try 'Clock Setting' on page 59.
• Moisture has condensed inside the unit. Leave the unit turned On for
about 2 hours until the moisture evaporates.
• If there is a Power failure or unplugging during Recording, Finalizing,
Formatting or Editing (even after "Repairing" disappears), a Repairing
Process will begin automatically just after turning the unit On again. It
may take several minutes up to several hours.
• If you intend to Cancel the Repairing Process, press [ A (Open/
Close) ] on the Front Panel, then Select "Yes" and press [ OK ].
After that, press [ A (Open/Close) ] to take Out the Disc. The Disc
cancelled during the Repairing Process MAY NOT work.
• Check that the AC Power cord is connected securely.
• (In case of Power failure) Check the breaker and Clock Setting.
• When "Standby Settings" is set to "Energy Saving Standby", the
Front Panel lighting is Off in Standby mode.
• Enter 4737 in "Change Password" to Reset the password.
STANDBY / ON] button on the Front Panel for
STANDBY / ON] button on the Front Panel for more than
Advertisement
Table of Contents
