Table of Contents
Advertisement
Network Connection
FWZH776/676F
If you would like to proceed with the Network Connection
setting, perform this setting. If you would like to Skip this
setting, Select "No" using [ K / L ], then press [ OK ]. Move
on to 'HDMI CEC' on page 25.
9
Select "Yes", then press [ OK ].
• Selecting "Yes" increases the Power
Consumption instead of Selecting "No", when
the Power is Off in Standby mode.
10
Select "Wired" or "Wireless" using
[ K / L ], then press [ OK ].
If you connect this unit to the
Network using an Ethernet Cable,
Select "Wired" to Connect to the
Internet.
Wired
If you have a Wireless Router,
Wireless
Select "Wireless" to Connect to
the Internet.
For Wired Connection
For Wired Connection
A
Connection test will Start automatically.
1.
Select "Auto". After Connection test, the test
result will be Displayed. Press [ OK ].
• Please move on to 'Network Function' on page 25.
• If you Select "Manual", refer to 'Manual' on page 43.
For Wireless Connection
For Wireless Connection
B
Select "Auto Scan", "Manual" or "Easy Connect" using
[ K / L ], then press [ OK ].
This Setting automatically
searches for Wireless Networks.
Auto Scan
Select this Setting if you wish
Manual
to Configure the Wireless
Easy Connect
Networks manually.
Select this Setting if your
Wireless Router has a PBC
button
. It is the easiest way to
*1
set up a Wireless Connection.
If it fails, try "Easy Connect"
again.
*2
*1 PBC (Push Button Configuration) button may be
the Button's name that your Router uses. If not
then refer to the Router's Manual for more details.
*2 If it continuously fails, then refer to the Router's
Manual for more details.
a
"Auto Scan" Method
• AP (Access Point) List will appear.
1.
Select an AP to which you would like to connect
this unit using [ K / L ], then press [ OK ].
• If you Select an AP which does not support TKIP,
a Security Key Entry screen will appear. Enter the
Security Key using the On-screen Software Keyboard.
• Follow the On-screen Instructions.
• For details on how to use the Software Keyboard,
refer to 'Guide to the Software Keyboard' on page 25.
EN - 24
2.
After the Connection Test, the test result will be
Displayed. Press [ OK ].
• Please move on to 'Network Function' on page
25.
b
"Manual" Method
• SSID Input Screen will appear.
1.
Enter the SSID using the On-screen Software
Keyboard.
• Security mode Select screen will appear.
2.
Select a Security mode :
"None" or "AES+TKIP" or "WEP" .
• Security Key Input Screen will appear.
3.
Enter a Security Key using the On-screen
Software Keyboard.
• Connection test will Start automatically.
4.
After the Connection test, the test result will be
A
Displayed. Press [ OK ].
5.
Please move on to 'Unit Name' on page 25.
c
"Easy Connect" Method
B
Push Button Method
1.
Select "Push Button Method".
2.
Press the PBC button on your Wireless Router.
• Connection test will Start automatically.
3.
After Connection test, the test result will be
Displayed. Press [ OK ].
• Please move on to 'Network Function' on page
25.
PIN Code Method
1.
Select "PIN Code Method".
2.
Select an AP to which you would like to Connect
this unit using [ K / L ], then press [ OK ].
3.
PIN Code will appear On-screen, then Input the
a
Code into AP.
• Refer to the Router's Manual for Inputting PIN
Code.
• Connection test will Start automatically.
b
4.
After Connection test, the test result will be
Displayed. Press [ OK ].
• Please move on to 'Network Function' on page
25.
c
Note(s)
• "Easy Connect" method is only available when your
Wireless Router supports it. For details, please refer
to the Owner's Manual of your Wireless Router.
• If more than 64 AP's are found, a Confirmation
message will appear, then the Screen goes back to
the AP List.
• Connection test will automatically Start when you
Select an AP that does not have an Authentication
Method.
Continued on next page.
Advertisement
Table of Contents
