Yamaha 006IPTO-F0 Owner's Manual page 315

REV->CHORUS
One input, two output reverb and chorus effects in
series.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
THRU,
HPF High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
Reverb and chorused reverb bal-
REV.BAL 0–100% ance (0% = all chorused reverb,
100% = all reverb)
FREQ. 0.05–40.00 Hz Modulation speed
AM DEPTH 0–100% Amplitude modulation depth
PM DEPTH 0–100% Pitch modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
WAVE Sine, Tri Modulation waveform
SYNC OFF, ON Tempo parameter sync on/off
Used in conjunction with
1
NOTE
TEMPO to determine FREQ.
1.
REV+FLANGE
One input, two output reverb and flanger effects in
parallel.
Parameter Range
REV TIME 0.3–99.0 s Reverb time
INI. DLY 0.0–500.0 ms Initial delay before reverb begins
HI. RATIO 0.1–1.0 High-frequency reverb time ratio
DIFF. 0–10 Spread
DENSITY 0–100% Reverb density
THRU,
HPF High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
LPF Low-pass filter cutoff frequency
THRU
Reverb and flange balance (0% =
REV/FLG 0–100%
all reverb, 100% = all flange)
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
MOD. DLY 0.0–500.0 ms Modulation delay time
Feedback gain (plus values for
normal-phase feedback, minus
FB. GAIN –99 to +99%
values for reverse-phase feed-
back)
WAVE Sine, Tri Modulation waveform
SYNC OFF, ON Tempo parameter sync on/off
Used in conjunction with
1
NOTE
TEMPO to determine FREQ.
1.
REV->FLANGE
One input, two output reverb and flanger effects in
series.
Description Parameter
REV TIME
INI. DLY
HI. RATIO
DIFF.
DENSITY
HPF
LPF
REV.BAL
FREQ.
DEPTH
MOD. DLY
FB. GAIN
WAVE
SYNC
NOTE
1.
REV+SYMPHO.
One input, two output reverb and symphonic effects
Description
in parallel.
Parameter
REV TIME
INI. DLY
HI. RATIO
DIFF.
DENSITY
HPF
LPF
REV/SYM
FREQ.
DEPTH
MOD. DLY
WAVE
SYNC
NOTE
1.
Effects Parameters
Range Description
0.3–99.0 s Reverb time
0.0–500.0 ms Initial delay before reverb begins
0.1–1.0 High-frequency reverb time ratio
0–10 Spread
0–100% Reverb density
THRU,
High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
Reverb and flanged reverb bal-
0–100% ance (0% = all flanged reverb,
100% = all reverb)
0.05–40.00 Hz Modulation speed
0–100% Modulation depth
0.0–500.0 ms Modulation delay time
Feedback gain (plus values for
normal-phase feedback, minus
–99 to +99%
values for reverse-phase feed-
back)
Sine, Tri Modulation waveform
OFF, ON Tempo parameter sync on/off
Used in conjunction with
1
TEMPO to determine FREQ.
Range Description
0.3–99.0 s Reverb time
0.0–500.0 ms Initial delay before reverb begins
0.1–1.0 High-frequency reverb time ratio
0–10 Spread
0–100% Reverb density
THRU,
High-pass filter cutoff frequency
21.2 Hz–8.00 kHz
50.0 Hz–16.0 kHz,
Low-pass filter cutoff frequency
THRU
Reverb and symphonic balance
0–100% (0% = all reverb, 100% = all
symphonic)
0.05–40.00 Hz Modulation speed
0–100% Modulation depth
0.0–500.0 ms Modulation delay time
Sine, Tri Modulation waveform
OFF, ON Tempo parameter sync on/off
Used in conjunction with
1
TEMPO to determine FREQ.
DM1000 Version 2—Owner's Manual
315