Mitsubishi Electric 800 Series Instruction Manual page 42

*7
Device No.
Not used
RY(n+1)8
(initial data process completion flag)
Not used
RY(n+1)9
(initial data process request flag)
RY(n+1)A Error reset request flag
RY(n+1)B
Pr.187 assignment function (NET X3)
RY(n+1)C
Pr.188 assignment function (NET X4)
RY(n+1)D
Pr.189 assignment function (NET X5)
RY(n+1)E
Reserved
RY(n+1)F
*1 These signals are set in the initial setting. Using Pr.180 to Pr.183, input signals assigned to the device numbers can be changed.
For details of Pr.180 to Pr.183, refer to the FR-E800 Instruction Manual (Function).
*2 The signals are fixed. They cannot be changed using parameters.
*3 These signals are set in the initial setting. Using Pr.190 to Pr.192, output signals assigned to the device numbers can be changed.
For details of Pr.190 to Pr.192, refer to the FR-E800 Instruction Manual (Function).
*4 Output signal can be assigned using Pr.313 to Pr.315.
For details, refer to the description of Pr.190 to Pr.196 (Output terminal function selection) in the FR-E800 Instruction Manual (Function).
*5 Input signals can be assigned using Pr.184 to Pr.189.
For details, refer to the description of Pr.184 to Pr.189 (Input terminal function selection) in the FR-E800 Instruction Manual (Function).
*6 Output signals can be assigned using Pr.193 to Pr.196.
For details, refer to the description of Pr.193 to Pr.196 (Output terminal function selection) in the FR-E800 Instruction Manual (Function).
*7 "n" indicates a value determined by the station number.
• Remote registers
Description
*5
Address
Upper 8 bits
RWwn Monitor code 2
Set frequency (0.01 Hz increments) /
RWwn+1
torque command
*1
RWwn+2
H00 (arbitrary)
RWwn+3 Data to be written
*1 The upper 8 bits always contains H00 even a different value is set.
*2 When Pr.804 = "3 or 5" during torque control under Real sensorless vector control, a torque command value is set in RWwn+1.
*3 The display can be changed to rotations per minute (machine speed) using Pr.37 and Pr.53.
*4 When the output frequency or the set frequency is selected as the monitor item, rotations per minute (machine speed) can be displayed using
Pr.37 and setting "4" in Pr.53.
*5 "n" indicates a value determined by the station number.
 When Pr.544 = "1" (compatible with CC-Link Ver.1)
• Remote I/O signals
Settings are the same as those when Pr.544 = "0". (Refer to
• Remote registers
Description
*4
Address
Upper 8 bits
RWwn Monitor code 2
Set frequency (0.01 Hz increments) /
RWwn+1
torque command
Link parameter
RWwn+2
extended setting
RWwn+3 Data to be written
*1 When Pr.804 = "3 or 5" during torque control under Real sensorless vector control, a torque command value is set in RWwn+1.
*2 The display can be changed to rotations per minute (machine speed) using Pr.37 and Pr.53.
*3 When the output frequency or the set frequency is selected as the monitor item, rotations per minute (machine speed) can be displayed using
Pr.37 and setting "4" in Pr.53.
*4 "n" indicates a value determined by the station number.
 When Pr.544 = "12" (Compatible with the double setting of CC-Link Ver.2)
• Remote I/O signals
Settings are the same as those when Pr.544 = "0". (Refer to
Refer to
Signal
page
—
—
44
*5
44
*5
44
*5
44
—
Refer to
page
Lower 8 bits
Monitor code 1 45
46
*2*3
Instruction code 46
46
Refer to
page
Lower 8 bits
Monitor code 1 45
46
*1*2
Instruction code 46
46
*7
Device No.
Not used
RX(n+1)8
(initial data process request flag)
Not used
RX(n+1)9
(initial data process completion flag)
RX(n+1)A Error status flag
RX(n+1)B Remote station ready
RX(n+1)C to
Reserved
RX(n+1)F
*5
Address Description
RWrn
First monitor value
RWrn+1
Second monitor value
RWrn+2 Reply code
RWrn+3 Data to be read
page 40.)
Description
*4
Address
Upper 8 bits
RWrn
First monitor value
RWrn+1
Second monitor value
RWrn+2 Reply code 2
RWrn+3 Data to be read
page 40.)
2.6 CC-Link IE Field Network Basic
Refer to
Signal
page
—
—
45
45
—
Refer to
page
*4
47
*4
47
47
47
Refer to
page
Lower 8 bits
*3
47
*3
47
Reply code 1 47
47
2. Ethernet Communication
1
2
3
4
5
6
7
8
9
10
41