Menu Descriptions; Menu Overview - ABB Navigator 500 Series Operating Instructions Manual

Navigator 500
Sodium analyzer

7 Menu descriptions

7.1 Menu overview

Refer to Section 7.1.1, page 43
Menu
Calibrate
Exit
Sodium 1 – 4
Sensor Calibration
Low Calibration
High Calibration
Two-Point Cal
Regeneration Cycle
Process Calibration
Grab Sample
Scheduled Calibration
Type
Frequency
Interval
Time of Next Cal.
Refer to Section 7.1.4, page 50
Menu
Display
Exit
Language
Settings
Operator Templates
Page 1 (5) Template
Date & Time
Chart View
Channel 1 – 4
Source
Tag
Chart Duration
View/Log Enables
Diagnostic View
Signals View
Chart View
Alarm View
Analog OP View
Calibration Log
Alarm Log
Audit Log
Refer to Section 7.1.7, page 55
Menu
Media Card
Exit
Card Status
Process Data
Channel 1 – 6
Sampling Time
Data Logging
Save Configuration
Select File Name (8)
Load Configuration
Select File (8)
Quick Format
Note. Service level menus (not shown) are
password-protected at the factory and intended for
use by authorised ABB service technicians only.
Fig. 7.1 Overview of sodium menus
42
Select
Sodium 1 – 4
Calibration Setup
Low Std Solution
High Std Solution
Recovery Time
Grab Sample Time
Restore Defaults
Hold Outputs
Select
Analog Outputs
Brightness
Contrast
Date Format
Time & Date
Daylight Saving
DS Region
DS Start Time
DS End Time
DS Start Occur
DS End Occur
DS Start Day
DS End Day
DS Start Month
DS End Month
Refer to Section 7.1.8, page 56
Menu
Communication
Exit
Select
Profibus
Slave Address
Baud rate
Ethernet
DHCP
IP Address
Subnet Mask
Default Gateway
Email
SMTP Server ID
Recipients
Triggers
Refer to Section 7.1.2, page 46
Menu
Sensor Setup
Exit
Select
Stream Settings
Tag
Stream 1 (3) Tag Sample Time
Units
Sequence
Range High
Stream 1 (3)
Stream 1 (3) Range High
Man. Valve Control
Range Low
Low Standard Valve
Stream 1 (3) Range Low
High Standard Valve
Filter Type
Stream Valve
Filter Time
Stream Valve 1 (3)
Wetting Routine
Regeneration Valve
Solution Detection
Reset to Defaults
Flow Meter
Flow Meter 1 – 3
Refer to Section 7.1.5, page 52
Menu
Input/Output
Exit
Select
Digital I/O
Analog Output 1 – 4 Digital I/O 1 – 6
Type
Source
Source
Output Type
Polarity
Elec. Low
Elec. High
Relays
Eng. Low
Relay 1 – 6
Eng. High
Source
Output Failure
Polarity
Failure Current
Select
Transmitter
Ethernet
Input/Output
Email Address 1 – 3
Tag 1 – 4
Source 1 – 4
Invert 1 – 4
7 Menu descriptions
Refer to Section 7.1.3, page 48
Menu
Device Setup
Exit
Initial Setup
Instrument Tag
Temperature Units
Reset to Defaults
Security Setup
Calibrate Password
Advanced Password
Reset Passwords
Range Change Setup
Range Change
Range 1(3) Span
Refer to Section 7.1.6, page 54
Menu
Process Alarm
Exit
Alarm 1 – 8
Source
Type
Tag
Trip
Hysteresis
Time Hysteresis
Refer to Section 7.1.9, page 57
Menu
Device Info
Exit
Select
Media Card Unit
Software Version
Serial Number
Hardware Version
Date of manufacture
Hardware Revision
Sensor 1 – 4
Software Revision
Type
Serial Number
Date of manufacture
Ethernet Revision
Hardware Revision
MAC Address
Software Revision
No. Analog Inputs
No. Analog Outputs
No. Relays
OI/ASO550–EN Rev. G
Select
Select