Mitsubishi Electric MELSEC-Q QD75M User Manual page 850

Motor current value (
Motor rotation speed (
Motor type (
Pr.103
Monitor output offset (
Movement amount per pulse (
....................................................................... 5-22
Movement amount per rotation (
Multiple axes simultaneous start control .... 10-20
Multiple PLC .................................................... 2-6
[N]
Names of each part......................................... 4-3
Near pass function ...................................... 12-20
Near pass .................................................... 12-20
Near-point dog method machine OPR ........... 8-6
Near-point dog signal .................................... 3-18
New acceleration time value (
New current value ....................................... 9-106
New current value (
New deceleration time value (
New speed value (
New torque value (
NEXT start ................................................... 10-15
No. of control axes .......................................... 3-2
No. of modules can be mounted..................... 2-5
No. of occupied I/O points............................... 3-3
No. of pulses per rotation (
No. of write accesses to flash ROM (
..................................................................... 5-118
NOP instruction ........................................... 9-111
Normal start ................................................... 10-8
[O]
Pr.45
OP address (
Pr.53
OP shift amount (
OP shift function ............................................ 12-8
Operating principle .......................................... 1-7
Operation pattern (
Operation patterns........................................... 9-5
Operation timing and processing time during
position-speed switching control................... 9-94
Operation timing and processing time during
speed-position switching control (ABS mode)
....................................................................... 9-94
) ................... 5-134
Md.104
) ................. 5-134
Md.103
) .................................... 5-60
) .................... 5-74
Pr.127
Pr.2 Pr.4
to
Pr.3
) ...... 5-22
Cd.10
) ...... 5-144
Cd.9
)......................... 5-142
Cd.11
) ...... 5-144
Cd.14
) ........................ 5-146
Cd.22
)........................ 5-150
Pr.2
) ............... 5-22
Md.19
)................................... 5-50
) ............................ 5-56
Da.1
)............................ 5-84
Operation timing and processing time during
speed-position switching control (INC mode)
........................................................................9-86
Operation timing and processing time of fast
OPR................................................................8-14
)
OPR acceleration time selection (
OPR basic parameters ..................................5-48
OPR complete flag.......................................5-126
OPR deceleration time selection (
OPR detailed parameters ..............................5-54
OPR direction (
OPR method ....................................................8-5
OPR method (
OPR method (1): Near-point dog method.......8-6
OPR method (2): Count method 1)
..........................................................................8-8
OPR method (3): Count method 2)
........................................................................8-10
OPR method (4): Data set method ...............8-12
OPR request ....................................................8-2
OPR request flag .........................................5-126
OPR request flag OFF request (
......................................................................5-150
OPR request OFF program ...........................6-35
OPR retry (
OPR re-travel value (
OPR retry function .........................................12-4
OPR speed (
)
OPR torque limit value (
Optional function 1 (
Optional function 2 (
Optional function 5 (
Optional function 6 (
Optional function C (
Order of priority for stop process...................6-72
Outline design of positioning system.............1-18
Outline of installation, wiring and maintenance
..........................................................................4-2
Outline of OPR control.....................................8-2
Outline for restarting ......................................1-27
Outline of starting...........................................1-24
Outline of stopping .........................................1-26
Override function..........................................12-44
Override program...........................................6-44
Index - 5
Pr.44
) ................................5-50
Pr.43
)..................................5-48
Cd.19
Pr.48
).......................................5-52
) ....................5-134
Md.100
Pr.46
)....................................5-50
Pr.54
) ..................5-56
).........................5-70
Pr.123
).........................5-72
Pr.124
).........................5-74
Pr.132
).........................5-74
Pr.133
) ........................5-80
Pr.160
Pr.51
) ..5-54
Pr.52
) ..5-54
)