1. Manuals
  2. Brands
  3. ABB Manuals
  4. Protection Device
  5. REB650
  6. Manual

ABB REB650 Manual

Relion dnp, 650 series version 2.2
Hide thumbs Also See for REB650:
Table of Contents

Advertisement

Quick Links

See also: Technical Manual
—
R E L I O N ® 650 SERIES
DNP, 650 series
Version 2.2
Point list manual

Advertisement

Table of Contents
loading

Related Manuals for ABB REB650

Summary of Contents for ABB REB650

  • Page 1 — R E L I O N ® 650 SERIES DNP, 650 series Version 2.2 Point list manual...
  • Page 3 Document ID: 1MRK 511 419-UUS Issued: October 2017 Revision: A Product version: 2.2.1 © Copyright 2017 ABB. All rights reserved...
  • Page 4 Copyright This document and parts thereof must not be reproduced or copied without written permission from ABB, and the contents thereof must not be imparted to a third party, nor used for any unauthorized purpose. The software and hardware described in this document is furnished under a license and may be used or disclosed only in accordance with the terms of such license.
  • Page 5 In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other than under explicit contractual commitments, in no event shall ABB be responsible or liable for any loss or damage resulting from the use of this manual or the application of the equipment.
  • Page 6 (EMC Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB in accordance with the product standard EN 60255-26 for the EMC directive, and with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive.

  • Page 7: Table Of Contents

    Table of contents Table of contents Section 1 Introduction................3 This manual....................3 Intended audience..................3 Product documentation................4 Product documentation set..............4 Document revision history..............5 Related documents................6 Document symbols and conventions............7 Symbols....................7 Document conventions................ 8 Section 2 DNP3 data mappings............11 Overview....................11 Point list for the IEDs................

  • Page 9: Section 1 Introduction

    Section 1 1MRK 511 419-UUS A Introduction Section 1 Introduction This manual GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v18 The point list manual describes the outlook and properties of the data points specific to the IED. The manual should be used in conjunction with the corresponding communication protocol manual.

  • Page 10: Product Documentation

    Section 1 1MRK 511 419-UUS A Introduction Product documentation 1.3.1 Product documentation set GUID-3AA69EA6-F1D8-47C6-A8E6-562F29C67172 v15 Engineering manual Installation manual Commissioning manual Operation manual Application manual Technical manual Communication protocol manual Cyber security deployment guideline IEC07000220-4-en.vsd IEC07000220 V4 EN-US Figure 1: The intended use of manuals throughout the product lifecycle The engineering manual contains instructions on how to engineer the IEDs using the various tools available within the PCM600 software.

  • Page 11: Document Revision History

    Section 1 1MRK 511 419-UUS A Introduction The commissioning manual contains instructions on how to commission the IED. The manual can also be used by system engineers and maintenance personnel for assistance during the testing phase. The manual provides procedures for the checking of external circuitry and energizing the IED, parameter setting and configuration as well as verifying settings by secondary injection.

  • Page 12: Related Documents

    Section 1 1MRK 511 419-UUS A Introduction 1.3.3 Related documents GUID-94E8A5CA-BE1B-45AF-81E7-5A41D34EE112 v5 Documents related to REB650 Document numbers Application manual 1MRK 505 388-UEN Commissioning manual 1MRK 505 390-UEN Product guide 1MRK 505 391-BEN Technical manual 1MRK 505 389-UEN Type test certificate...

  • Page 13: Document Symbols And Conventions

    Section 1 1MRK 511 419-UUS A Introduction Documents related to RET650 Document numbers Application manual 1MRK 504 169-UEN Commissioning manual 1MRK 504 171-UEN Product guide 1MRK 504 172-BEN Technical manual 1MRK 504 170-UEN Type test certificate 1MRK 504 172-TEN 650 series manuals Document numbers Operation manual 1MRK 500 128-UEN...

  • Page 14: Document Conventions

    Section 1 1MRK 511 419-UUS A Introduction The caution icon indicates important information or warning related to the concept discussed in the text. It might indicate the presence of a hazard which could result in corruption of software or damage to equipment or property.
  • Page 15 Section 1 1MRK 511 419-UUS A Introduction • Signals in frames with a shaded area on their right hand side represent setting parameter signals that are only settable via the PST, ECT or LHMI. • If an internal signal path cannot be drawn with a continuous line, the suffix - int is added to the signal name to indicate where the signal starts and continues.

  • Page 17: Section 2 Dnp3 Data Mappings

    Section 2 1MRK 511 419-UUS A DNP3 data mappings Section 2 DNP3 data mappings Overview GUID-EC7D1F5E-FFE0-4837-B02A-45E1CD531A94 v3 This document describes the available DNP3 data points and structures in the IEDs. The data points are unmapped as a default. The point list tables represents the superset of available DNP3 data points in these IEDs.
  • Page 18 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description Binary input 4 Binary input 5 Binary input 6 Binary input 7 Binary input 8 Binary input 9 BI10 Binary input 10 BI11 Binary input 11 BI12 Binary input 12 BI13...
  • Page 19 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description Binary input 7 Binary input 8 BLKOUT Block binary outputs Binary output 1 Binary output 2 Binary output 3 Binary output 4 Binary output 5 Binary output 6 Binary output 7 Binary output 8...
  • Page 20 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description CMDBIT31 Command out bit 31 CMDBIT32 Command out bit 32 General functions for showing signals for DNP master MVGAPC Analog inputs Magnitude of deadband value SP16GAPC Binary inputs Input 1 status...
  • Page 21 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description TRRET Retrip by breaker failure protection function TRRET_A Retrip by breaker failure protection function phase A TRRET_B Retrip by breaker failure protection function phase B TRRET_C Retrip by breaker failure protection function phase C CCSSPVC...
  • Page 22 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description Ch2FltAng Fault Angle Ch2FltMag Fault Magnitude Ch2Mag Prefault Magnitude Ch3Ang Prefault Angle Ch3FltAng Fault Angle Ch3FltMag Fault Magnitude Ch3Mag Prefault Magnitude Ch4Ang Prefault Angle Ch4FltAng Fault Angle Ch4FltMag...
  • Page 23 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description Ch14FltMag Fault Magnitude Ch14Mag Prefault Magnitude Ch15Ang Prefault Angle Ch15FltAng Fault Angle Ch15FltMag Fault Magnitude Ch15Mag Prefault Magnitude Ch16Ang Prefault Angle Ch16FltAng Fault Angle Ch16FltMag Fault Magnitude Ch16Mag...
  • Page 24 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description Ch26Mag Prefault Magnitude Ch27Ang Prefault Angle Ch27FltAng Fault Angle Ch27FltMag Fault Magnitude Ch27Mag Prefault Magnitude Ch28Ang Prefault Angle Ch28FltAng Fault Angle Ch28FltMag Fault Magnitude Ch28Mag Prefault Magnitude Ch29Ang...
  • Page 25 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description EF4PTOC Binary inputs PUFW Pick up foward direction PUREV Pick up reverse direction TRST1 Trip signal from step 1 TRST2 Trip signal from step 2 TRST3 Trip signal from step 3 TRST4...
  • Page 26 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description LOVPTUV Binary inputs TRIP Trip signal LT3CPDIF Binary inputs BLK2H Block signal due to second harmonic BLK5H Block signal due to fifth harmonic INTFAULT Internal fault has been detected OPENCTAL Open CT Alarm output signal.
  • Page 27 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description TRST2_B Trip signal from step2 phase B TRST2_C Trip signal from step2 phase C TRIP Trip PCFCNT Analog inputs SCAL_VAL Scaled value with time and status information Counters CNT_VAL Actual pulse counter value...

  • Page 28: Bi4 Binary Input

    Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description AUTOREL Automatic release MANREL Manual release SLGAPC Analog inputs SWPOSN Switch position (integer) Binary outputs CLOSE_CMD Close command parameter for DNP protocol OPEN_CMD Open command parameter for DNP protocol SMBI Binary inputs Binary input 1...
  • Page 29 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description COUNTAR Counting total number of reclosing shots SMPPTRC Binary inputs CLLKOUT Circuit breaker lockout output (set until reset) TR1P Tripping single-pole TR2P Tripping two-pole TR3P Tripping three-pole TRIP...
  • Page 30 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description TRNSSENS Trip signal from sensitive negative sequence differential protection TRNSUNR Trip signal from unrestrained negative sequence differential protection TEIGAPC Binary inputs ALARM Indicator of the integrated time has reached the alarm limit WARNING Indicator of the integrated time has reached the warning limit TEILGAPC...
  • Page 31 Section 2 1MRK 511 419-UUS A DNP3 data mappings Function name Signal type Signal name Description VNMMXU Analog inputs VA Amplitude, magnitude of reported value VA_ANGL VA Angle, magnitude of reported value VB Amplitude, magnitude of reported value VB_ANGL VB Angle, magnitude of reported value VC Amplitude, magnitude of reported value VC_ANGL V_C Angle, magnitude of reported value...

  • Page 33: Section 3 Dnp3 Protocol Implementation

    Device identification 1.1 Device identification Capabilities Current value If configurable, list methods 1.1.1 Device function Outstation Outstation 1.1.2 Vendor name ABB AB 1.1.3 Device name 650 series 1.1.4 Device manufacturer's hardware version 1.1.5 Device manufacturer's software version 1.1.6 Device profile...
  • Page 34 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.1 Device identification Capabilities Current value If configurable, list methods 1.1.8 Supported function PST or LHMI blocks ● Self Address Reservation ○ Data Sets ○ File Transfer ○ Virtual Terminal ○ Mapping to IEC 61850 Object Models defined in a DNP3 XML file ○...
  • Page 35 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.1 Device identification Capabilities Current value If configurable, list methods 1.1.12 DNP3 XML files Filename Description of contents Not supported available off-line ○ ● dnpDp.xml Complete device profile ○ ○ dnpDPCap.xml Device profile capabilities ○...
  • Page 36 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.2a Serial connections Capabilities Current value If configurable, list methods ● None None PST of LHMI (tRxToTxMinDel) ○RS-485 options: ● Requires Rx inactive before Tx ○ Other, explain: 1.2.5 Interval to request link status. Indicates how often to send Data Link Layer status requests on a serial connection. This parameter is separate from the TCP Keep-alive timer.
  • Page 37 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.2a Serial connections Capabilities Current value If configurable, list methods ● Not Checked Not checked ○ No gap permitted ○ Fixed at _____ bit times ○ Fixed at _____ ms ○ Configurable, range ____ to ____ bit times ○...
  • Page 38 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.2b Serial Capabilities Current If configurable, connections value list methods ● None None PST or LHMI (tRxToTxMin RS–485 Options: Del) ● Requires Rx inactive before Tx ○ Other, explain: 1.2.5 Interval to request link status: Indicates how often to send Data Link Layer status requests on a serial connection. This parameter is separate from the TCP Keep-alive timer.
  • Page 39 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.2b Serial Capabilities Current If configurable, connections value list methods ● Not checked checked ○ No gap permitted ○ Fixed at bit times ○ Fixed at ms ○ Configurable, range ___ to ___ bit times ○...
  • Page 40 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.3 IP networking Capabilities Current value If configurable, list methods ● Allows all (show as *.*.*.* in 1.3.7) Specified IP- Address ● Limits based on IP address ○ Limits based on list of IP addresses ●...
  • Page 41 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.3 IP networking Capabilities Current value If configurable, list methods ○ Fixed at 20,000 ○ Configurable, range _______ to _______ ○ Configurable, selectable from ____,____,____ ○ Configurable, other, describe: 1.3.13 Destination UDP port for initial unsolicited null responses (UDP only Outstations): For a UDP only Outstation, the destination UDP port for sending initial unsolicited Null response.
  • Page 42 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation Table 6: Link layer 1.4 Link layer Capabilities Current value If configurable, list methods 1.4.1 Data Link Address: Indicates if the link address is configurable over the entire valid range of 0 to 65,519. Data link addresses 0xFFF0 through 0xFFFF are reserved for broadcast or other special purposes.
  • Page 43 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.4 Link layer Capabilities Current value If configurable, list methods ○ None PST or LHMI (DLinkRetries) ○ Fixed at ● Configurable, range 0 to 255 ○ Configurable, selectable from ____,____,____ ○ Configurable, other, describe: 1.4.8 Maximum number of octets transmitted in a data link frame: This number includes the CRCs.
  • Page 44 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.5 Application layer Capabilities Current value If configurable, list methods ○ Fixed at 2048 PST or LHMI (ApLayMaxRxSize) ● Configurable, range 20 to 2048 ○ Configurable, selectable from ____,____,____ ○ Configurable, other, describe: 1.5.4 Time-out waiting for complete application layer fragment: Time-out if all frames of a message fragment are not received in the specified time.
  • Page 45 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.5 Application layer Capabilities Current value If configurable, list methods 1.5.9 Control Status Codes Supported: Indicates which control status codes are supported by the device: • Masters must indicate which control status codes they accept in outstation responses •...
  • Page 46 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.7 Fill out the Capabilities Current value If configurable, list following items for methods outstations only 1.7.2 How often is time synchronization required from the master: Details of when the master needs to perform a time synchronization to ensure that the outstation clock does not drift outside of an acceptable tolerance.
  • Page 47 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.7 Fill out the Capabilities Current value If configurable, list following items for methods outstations only ● Per Object Group (see part 3) per Object Group ○ Per Object Group (see part 3) Class 1: Fixed at______ Configurable, range _______ to...
  • Page 48 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation ○ Always Sometimes ● Sometimes, explain: Only when it contains events ○ Never 1.7.9 DNP command settings preserved through a device reset: If any of these settings are written through the DNP protocol and they are not preserved through a restart of the outstation, the Master will have to write them again anytime the Restart IIN bit is set.
  • Page 49 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.8 Outstation unsolicited Capabilities Current value If configurable, list methods response support ○ Fixed at PST or LHMI (MasterAddres) ● Configurable, range 0 to 65519 ○ Configurable, selectable from ____,____,____ ○ Configurable, other, describe: 1.8.3 Unsolicited response confirmation time-out: This is the amount of time that the outstation will wait for an application layer confirmation back from the master indicating that the master received the unsolicited response message.
  • Page 50 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.9 Outstation unsolicited Capabilities Current value If configurable, list methods response trigger conditions ○ Class 2 not used to trigger Unsolicited PST or LHMI Responses (UREvCntThold2) ○ Fixed at ● Configurable, range 1 to 100 ○...
  • Page 51 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.9 Outstation unsolicited Capabilities Current value If configurable, list methods response trigger conditions ○ Class 3 not used to trigger Unsolicited 5 seconds PST or LHMI Responses (tUREvBufTout3) ○ Fixed at ___________ ms ●...
  • Page 52 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.10 Outstation performance Capabilities Current value If configurable, list methods ● Never At startup and 1800 PST or LHMI seconds after last sync (tSynchTimeout) ● Asserted at startup until first Time Synchronization request received ○...
  • Page 53 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.10 Outstation performance Capabilities Current value If configurable, list methods 1.10.7 Maximum event time-tag error for local binary and double bit I/O (ms): The error between the time-tag reported and the absolute time of the physical event.
  • Page 54 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.13 Broadcast Capabilities Current Value If configurable, list functionality methods 1.13.1 Support for ○ Disabled broadcast functionality: ● Enabled ○ Configurable 1.13.2 Write functions Write clock (g50v1 with (FC = 2) supported with qualifier code 07): broadcast requests: ○...
  • Page 55 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.13 Broadcast Capabilities Current Value If configurable, list functionality methods 1.13.7 Freeze and clear ● Disabled functions (FC = 9) ○ Enabled supported with ○ Configurable broadcast requests: (described elsewhere 1.13.8 Freeze and ●...
  • Page 56 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 1.13 Broadcast Capabilities Current Value If configurable, list functionality methods 1.13.18 Enable Enable unsolicited by unsolicited functions event Class (g60v2, (FC = 20) supported g60v3 and g60v4 with with broadcast qualifier code 06): requests: ○...
  • Page 57 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.1 BINARY INPUTS Capabilities Current Value If configurable, list Static (Steady-State) (leave tick-boxes blank if methods Group Number: 1 Event this data type is not Group Number: 2 supported) 3.1.1 Static Variation reported when variation 0 requested or in response to Class polls: ●...
  • Page 58 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.6 DOUBLE-BIT Capabilities Current Value If configurable, list BINARY INPUTS Static (leave tick-boxes blank if methods (Steady-State) Group this data type is not Number: 3 Event Group supported) Number: 4 3.6.1 Static Variation reported when variation 0 requested or in response to Class polls: Note: The support for double-bit binary inputs can be determined remotely using protocol object Group 0 Variation 234.
  • Page 59 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.6 DOUBLE-BIT Capabilities Current Value If configurable, list BINARY INPUTS Static (leave tick-boxes blank if methods (Steady-State) Group this data type is not Number: 3 Event Group supported) Number: 4 ● Fixed at 1000 ○...
  • Page 60 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.7 BINARY OUTPUTS Capabilities Current Value If configurable, list AND BINARY OUTPUT (leave tick-boxes blank if methods COMMANDS this data type is not Binary Outputs Group supported) Number: 10 Binary Output Events Group Number: 11 Binary Output Commands Group...
  • Page 61 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.7 BINARY OUTPUTS Capabilities Current Value If configurable, list AND BINARY OUTPUT (leave tick-boxes blank if methods COMMANDS this data type is not Binary Outputs Group supported) Number: 10 Binary Output Events Group Number: 11 Binary Output Commands Group...
  • Page 62 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.7 BINARY OUTPUTS Capabilities Current Value If configurable, list AND BINARY OUTPUT (leave tick-boxes blank if methods COMMANDS this data type is not Binary Outputs Group supported) Number: 10 Binary Output Events Group Number: 11 Binary Output Commands Group...
  • Page 63 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.8 COUNTERS/ Capabilities Current Value If configurable, list FROZEN COUNTERS (leave tick-boxes blank if methods Counter Group Number: this data type is not supported) Frozen Counter Group Number: 21 Counter Event Group Number: 22 Frozen Counter Event Group Number: 23...
  • Page 64 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.8 COUNTERS/ Capabilities Current Value If configurable, list FROZEN COUNTERS (leave tick-boxes blank if methods Counter Group Number: this data type is not supported) Frozen Counter Group Number: 21 Counter Event Group Number: 22 Frozen Counter Event Group Number: 23...
  • Page 65 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.8 COUNTERS/ Capabilities Current Value If configurable, list FROZEN COUNTERS (leave tick-boxes blank if methods Counter Group Number: this data type is not supported) Frozen Counter Group Number: 21 Counter Event Group Number: 22 Frozen Counter Event Group Number: 23...
  • Page 66 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.8 COUNTERS/ Capabilities Current Value If configurable, list FROZEN COUNTERS (leave tick-boxes blank if methods Counter Group Number: this data type is not supported) Frozen Counter Group Number: 21 Counter Event Group Number: 22 Frozen Counter Event Group Number: 23...
  • Page 67 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.9 ANALOG INPUTS Capabilities Current Value If configurable, list Static (Steady-State) (leave tick-boxes blank if methods Group Number: 30 this data type is not Static Frozen Group supported) Number: 31 Event Group Number: 32 Frozen Analog Input Event Group Number: 33 Deadband Group...
  • Page 68 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.9 ANALOG INPUTS Capabilities Current Value If configurable, list Static (Steady-State) (leave tick-boxes blank if methods Group Number: 30 this data type is not Static Frozen Group supported) Number: 31 Event Group Number: 32 Frozen Analog Input Event Group Number: 33 Deadband Group...
  • Page 69 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.9 ANALOG INPUTS Capabilities Current Value If configurable, list Static (Steady-State) (leave tick-boxes blank if methods Group Number: 30 this data type is not Static Frozen Group supported) Number: 31 Event Group Number: 32 Frozen Analog Input Event Group Number: 33 Deadband Group...
  • Page 70 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.9 ANALOG INPUTS Capabilities Current Value If configurable, list Static (Steady-State) (leave tick-boxes blank if methods Group Number: 30 this data type is not Static Frozen Group supported) Number: 31 Event Group Number: 32 Frozen Analog Input Event Group Number: 33 Deadband Group...
  • Page 71 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.9 ANALOG INPUTS Capabilities Current Value If configurable, list Static (Steady-State) (leave tick-boxes blank if methods Group Number: 30 this data type is not Static Frozen Group supported) Number: 31 Event Group Number: 32 Frozen Analog Input Event Group Number: 33 Deadband Group...
  • Page 72 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.9 ANALOG INPUTS Capabilities Current Value If configurable, list Static (Steady-State) (leave tick-boxes blank if methods Group Number: 30 this data type is not Static Frozen Group supported) Number: 31 Event Group Number: 32 Frozen Analog Input Event Group Number: 33 Deadband Group...
  • Page 73 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.10 ANALOG OUTPUTS Capabilities Current Value If configurable, list AND ANALOG OUTPUT (leave tick-boxes blank if methods COMMANDS this data type is not supported) Analog Output Status Group Number: 40 Analog Outputs Group Number: 41 Analogue Output Events Group Number: 42 Analogue...
  • Page 74 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.10 ANALOG OUTPUTS Capabilities Current Value If configurable, list AND ANALOG OUTPUT (leave tick-boxes blank if methods COMMANDS this data type is not supported) Analog Output Status Group Number: 40 Analog Outputs Group Number: 41 Analogue Output Events Group Number: 42 Analogue...
  • Page 75 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.10 ANALOG OUTPUTS Capabilities Current Value If configurable, list AND ANALOG OUTPUT (leave tick-boxes blank if methods COMMANDS this data type is not supported) Analog Output Status Group Number: 40 Analog Outputs Group Number: 41 Analogue Output Events Group Number: 42 Analogue...
  • Page 76 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.10 ANALOG OUTPUTS Capabilities Current Value If configurable, list AND ANALOG OUTPUT (leave tick-boxes blank if methods COMMANDS this data type is not supported) Analog Output Status Group Number: 40 Analog Outputs Group Number: 41 Analogue Output Events Group Number: 42 Analogue...

  • Page 77: Dnp3 Implementation Table

    Section 3 1MRK 511 419-UUS A DNP3 protocol implementation 3.10 ANALOG OUTPUTS Capabilities Current Value If configurable, list AND ANALOG OUTPUT (leave tick-boxes blank if methods COMMANDS this data type is not supported) Analog Output Status Group Number: 40 Analog Outputs Group Number: 41 Analogue Output Events Group Number: 42 Analogue...
  • Page 78 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation Table 14: Implementation table DNP OBJECT GROUP AND VARIATION REQUEST (Slave will parse) RESPONSE (Slave will respond with) Object group Variation Function codes Function codes Qualifier codes number number Description (dec) Qualifier codes (hex) (dec) (hex)
  • Page 79 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation DNP OBJECT GROUP AND VARIATION REQUEST (Slave will parse) RESPONSE (Slave will respond with) Double bit input change 130 (unsol. resp) 17, 28 (index) event without time Double bit input change 1 (read) 06 (no range, or all) 129 (response)
  • Page 80 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation DNP OBJECT GROUP AND VARIATION REQUEST (Slave will parse) RESPONSE (Slave will respond with) 16–bit binary counter 1 (read) 00, 01 (start-stop) 129 (response) 00,01 (start-stop) (with flag) 06 (no range, or all) 17, 28 (index) 07, 08 (limited qty) 17, 27, 28 (index)
  • Page 81 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation DNP OBJECT GROUP AND VARIATION REQUEST (Slave will parse) RESPONSE (Slave will respond with) Analog input — single 1 (read) 00, 01 (start-stop) 129 (response) 00,01 (start-stop) precision, floating point 06 (no range, or all) 17, 28 (index) with flag 07, 08 (limited qty)
  • Page 82 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation DNP OBJECT GROUP AND VARIATION REQUEST (Slave will parse) RESPONSE (Slave will respond with) Analog input change 1 (read) 06 (no range, or all) 129 (response) 17, 28 (index) event — single 07, 08 (limited qty) precision, floating point with time...
  • Page 83 Section 3 1MRK 511 419-UUS A DNP3 protocol implementation DNP OBJECT GROUP AND VARIATION REQUEST (Slave will parse) RESPONSE (Slave will respond with) Class objects — class 2 1 (read) 06 (no range, or all) data 07, 08 (limited qty) Class objects —...

  • Page 85: Section 4 Glossary

    Section 4 1MRK 511 419-UUS A Glossary Section 4 Glossary Glossary M14893-1 v16 Alternating current Actual channel Application configuration tool within PCM600 A/D converter Analog-to-digital converter ADBS Amplitude deadband supervision Analog digital conversion module, with time synchronization Analog input ANSI American National Standards Institute Autoreclosing ASCT...
  • Page 86 Section 4 1MRK 511 419-UUS A Glossary C37.94 IEEE/ANSI protocol used when sending binary signals between IEDs Controller Area Network. ISO standard (ISO 11898) for serial communication Circuit breaker Combined backplane module CCITT Consultative Committee for International Telegraph and Telephony. A United Nations-sponsored standards body within the International Telecommunications Union.
  • Page 87 Section 4 1MRK 511 419-UUS A Glossary DARPA Defense Advanced Research Projects Agency (The US developer of the TCP/IP protocol etc.) DBDL Dead bus dead line DBLL Dead bus live line Direct current Data flow control Discrete Fourier transform DHCP Dynamic Host Configuration Protocol DIP-switch Small switch mounted on a printed circuit board...
  • Page 88 Section 4 1MRK 511 419-UUS A Glossary FOX 6Plus Compact time-division multiplexer for the transmission of up to seven duplex channels of digital data over optical fibers Flexible product naming File Transfer Protocol Function type G.703 Electrical and functional description for digital lines used by local telephone companies.
  • Page 89 Section 4 1MRK 511 419-UUS A Glossary IEEE Institute of Electrical and Electronics Engineers IEEE 802.12 A network technology standard that provides 100 Mbits/s on twisted-pair or optical fiber cable IEEE P1386.1 PCI Mezzanine Card (PMC) standard for local bus modules. References the CMC (IEEE P1386, also known as Common Mezzanine Card) standard for the mechanics and the PCI specifications from the PCI SIG (Special Interest Group) for...
  • Page 90 Section 4 1MRK 511 419-UUS A Glossary IRIG-B: InterRange Instrumentation Group Time code format B, standard 200 International Telecommunications Union Local area network LIB 520 High-voltage software module Liquid crystal display LDCM Line data communication module Local detection device Light-emitting diode LON network tool Local operating network Miniature circuit breaker...
  • Page 91 Section 4 1MRK 511 419-UUS A Glossary PCM600 Protection and control IED manager PC-MIP Mezzanine card standard PCI Mezzanine card Permissive overreach POTT Permissive overreach transfer trip Process bus Bus or LAN used at the process level, that is, in near proximity to the measured and/or controlled components Parallel redundancy protocol Power supply module...
  • Page 92 Section 4 1MRK 511 419-UUS A Glossary Serial communication module. SMA connector Subminiature version A, A threaded connector with constant impedance. Signal matrix tool within PCM600 Station monitoring system SNTP Simple network time protocol – is used to synchronize computer clocks on local area networks. This reduces the requirement to have accurate hardware clocks in every embedded system in a network.
  • Page 93 Section 4 1MRK 511 419-UUS A Glossary TPZ, TPY, TPX, TPS Current transformer class according to IEC Transformer Module. This module transforms currents and voltages taken from the process into levels suitable for further signal processing. Type identification User management tool Underreach A term used to describe how the relay behaves during a fault condition.
  • Page 96 — ABB AB Grid Automation Products 721 59 Västerås, Sweden Phone: +46 (0) 21 32 50 00 abb.com/protection-control © Copyright 2017 ABB. All rights reserved. Specifications subject to change without notice.

This manual is also suitable for:

Rec650Dnp3Red650Req650Ret650Dnp 670 series

Table of Contents