Video Osd Loginrequired - Cisco TelePresence MX200 G2 Administrator's Manual

Cisco TelePresence MX200 G2 and MX300 G2
Contents
Video SelfviewDefault FullscreenMode
Determine if the main video source (self-view) shall be shown in full screen or as a small
picture-in-picture (PiP) after a call. The setting only takes effect when self-view is switched on
(see the Video SelfviewDefault Mode setting).
Requires user role: ADMIN
Value space: <Off/Current/On>
Off: self-view will be shown as a PiP.
Current: The size of the self-view picture will be kept unchanged when leaving a call, i.e. if it
was a PiP during the call, it remains a PiP after the call; if it was fullscreen during the call, it
remains fullscreen after the call.
On: The self-view picture will be shown in fullscreen.
Video SelfviewDefault FullscreenMode: Current
Example:
Video SelfviewDefault PIPPosition
Determine the position on screen of the small self-view picture-in-picture (PiP) after a call. The
setting only takes effect when self-view is switched on (see the Video SelfviewDefault Mode
setting) and fullscreen view is switched off (see the Video SelfviewDefault FullscreenMode
setting).
Requires user role: ADMIN
Value space: <Current/UpperLeft/UpperCenter/UpperRight/CenterLeft/CenterRight/LowerLeft/
LowerRight >
Current: The position of the self-view PiP will be kept unchanged when leaving a call.
UpperLeft: The self-view PiP will appear in the upper left corner of the screen.
UpperCenter: The self-view PiP will appear in the upper center position.
UpperRight: The self-view PiP will appear in the upper right corner of the screen.
CenterLeft: The self-view PiP will appear in the center left position.
CentreRight: The self-view PiP will appear in the center right position.
LowerLeft: The self-view PiP will appear in the lower left corner of the screen.
LowerRight: The self-view PiP will appear in the lower right corner of the screen.
Video SelfviewDefault PIPPosition: Current
Example:
D15078.04 MX200 G2 and MX300 G2 Administrator Guide TC7.3, DECEMBER 2014.
Introduction Web interface System settings System settings
Video SelfviewDefault OnMonitorRole
Determine which monitor/output to display the main video source (self-view) on after a call.
Requires user role: ADMIN
Value space: <First/Second/Current>
First: The self-view picture will be shown on the main screen.
Second: The self-view picture will be shown on the secondary screen.
Current: When leaving a call, the self-view picture will be kept on the same screen as it was
during the call.
Video SelfviewDefault OnMonitorRole: Current
Example:
Video Monitors
Set the monitor layout mode to reflect the number of different layouts you want in your room
setup. Note that the second monitor can be reserved for presentations.
Requires user role: ADMIN
Value space: <Auto/DualPresentationOnly>
Auto: If a second monitor is connected, the layout is distributed on two monitors. Otherwise,
everything is displayed on the main monitor.
DualPresentationOnly: All participants in the call are shown on the main monitor. If a
presentation is part of the layout, the presentation is shown on the second monitor.
Video Monitors: Auto
Example:
Video OSD LanguageSelection
This has been replaced with the UserInterface OSD LanguageSelection setting.
Video OSD EncryptionIndicator
This has been replaced with the UserInterface OSD EncryptionIndicator setting.
Video OSD Output
This has been replaced with the UserInterface OSD Output setting.

Video OSD LoginRequired

This has been replaced with the UserInterface OSD LoginRequired setting.
www.cisco.com — Copyright © 2013–2014 Cisco Systems, Inc. All rights reserved.
109
Administrator Guide
Setting passwords Appendices