Cisco TelePresence MX200 G2 Administrator's Manual page 111

Cisco TelePresence MX200 G2 and MX300 G2
Contents
Video Output Connector [2] Location VerticalOffset
HorizontalOffset and VerticalOffset settings are associated with each video output. These
settings are used to signal the relative position of the displays that are connected to these
outputs. The integrated LCD display has HorizontalOffset = 0 and VerticalOffset = 0 (implicit,
not configurable).
HorizontalOffset = 0 and VerticalOffset = 0 indicates that the display is positioned in center,
both horizontally and vertically. A negative horizontal offset indicates that the monitor is left of
center, and a positive horizontal offset indicates that the monitor is right of center. A negative
vertical offset indicates that the monitor is below center, and a positive vertical offset indicates
that the monitor is above center. The magnitude of the offset indicates how far the display is
from center (relative to other displays).
Example: You have two displays side by side, one in center and one to the left. Then the
following settings will apply: HorizontalOffset = 0 for the center display, HorizontalOffset = -1 for
the left display.
Example: You have two displays, one in center and one below. Then the following settings will
apply: VerticalOffset = 0 for the center display, Vertical Offset = -1 for the lower display.
The default values for the different outputs are:
Video Output Connector [2] Location: HorizontalOffset = 1, VerticalOffset = 0
Requires user role: ADMIN
Value space: <-100..100>
Range: The value must be between -100 and 100.
Video Output Connector 2 Location Vertical Offset: 0
Example:
Video Output Connector [2] RGBQuantizatonRange
Devices connected to an HDMI output should follow the rules for RGB video quantization
range defined in CEA-861. Unfortunately some devices do not follow the standard and this
configuration may be used to override the settings to get a perfect image with any display. The
default value is set to Full because most HDMI displays expects full quantization range.
Requires user role: ADMIN
Value space: <Auto/Full/Limited>
Auto: RGB quantization range is automatically selected based on the RGB Quantization
Range bits (Q0, Q1) in the AVI infoframe. If no AVI infoframe is available, RGB quantization
range is selected based on video format according to CEA-861-E.
Full: Full quantization range. The R, G, B quantization range includes all code values (0 -
255). This is defined in CEA-861-E.
Limited: Limited Quantization Range. R, G, B quantization range that excludes some code
values at the extremes (16 - 235). This is defined in CEA-861-E.
Video Output Connector 2 RGBQuantizatonRange: Full
Example:
D15078.04 MX200 G2 and MX300 G2 Administrator Guide TC7.3, DECEMBER 2014.
Introduction Web interface System settings System settings
Video Output Connector [1..2] Resolution
Connector 1 (integrated LCD display): This value is fixed and cannot be changed.
Connector 2: Set the resolution and refresh rate for the monitor that is connected to the video
system's HDMI output.
Requires user role: ADMIN
Value space: Connector 1: <1920_1080_60> Connector 2: <Auto/1024_768_60/1280_1024_
60/1280_720_50/1280_720_60/1920_1080_50/1920_1080_60/1280_768_60/1360_768_60/
1366_768_60>
Auto: The system will automatically try to set the optimal resolution based on negotiation
with the connected monitor.
1024_768_60: The resolution is 1024 x 768, and the refresh rate is 60 Hz.
1280_1024_60: The resolution is 1280 x 1024, and the refresh rate is 60 Hz.
1280_720_50: The resolution is 1280 x 720, and the refresh rate is 50 Hz.
1280_720_60: The resolution is 1280 x 720, and the refresh rate is 60 Hz.
1920_1080_50: The resolution is 1920 x 1080, and the refresh rate is 50 Hz.
1920_1080_60: The resolution is 1920 x 1080, and the refresh rate is 60 Hz.
1280_768_60: The resolution is 1280 x 768, and the refresh rate is 60 Hz.
1360_768_60: The resolution is 1360 x 768, and the refresh rate is 60 Hz.
1366_768_60: The resolution is 1366 x 768, and the refresh rate is 60 Hz.
Video Output Connector 2 Resolution: Auto
Example:
Video WallPaper
This has been replaced with the UserInterface Wallpaper setting.
www.cisco.com — Copyright © 2013–2014 Cisco Systems, Inc. All rights reserved.
111
Administrator Guide
Setting passwords Appendices