7 Foam cushion tapes Flange nut Clip Green relay (5-pin) Template Illustration of the Engine Starter System Installed on the Vehicle ENGINE STARTER HARNESS RELAY (5-PIN) 2 FUSES 40A 3 RELAYS 2 FUSES 3A (4-PIN) 2 of 21 TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Long blade flat-tip screwdriver Small flat-tip screwdriver...
Page 3
Setting the Control Unit Get the control unit. Using a small flat-tip screwdriver, adjust the switches on the control unit to the locations shown. Using a isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Attach the protective tape to the control unit over the switches.
Page 4
Using the key, unlock the opener. Remove the left front door sill trim (two retaining tabs, five clips, and three hooks). 3 HOOKS FRONT LEFT FRONT DOOR SILL TRIM Pull away the weatherstrip, and remove the left kick panel (two clips). WEATHERSTRIP 2 CLIPS 4 of 21...
Page 5
Lower the tilt lever, and pull the steering wheel toward you. Insert a long blade flat-tip screwdriver along the guide of the column lower cover, and pry the retaining tab of the column upper cover. 2 RETAINING TABS Push. COLUMN UPPER COVER 2 HOOKS...
Page 6
12. If equipped, use a small flat-tip screwdriver to remove the left and right lens from the map light console (four retaining tabs for each lens). Remove the two bolts, and then release the map light console. BOLTS LENS 13. Remove the sunvisor holders. Using a small flat- tip screwdriver, push the hook, and turn the holder 90°, then pull it out.
Page 7
18. Pull away the weatherstrip from the left front pillar trim. Remove the left front pillar trim (two clips). LEFT FRONT 2 CLIPS PILLAR TRIM WEATHERSTRIP 19. Remove the clip from the left front pillar trim, and install a new clip on the left front pillar trim. NEW CLIP LEFT FRONT PILLAR TRIM...
Page 8
22. Using two pairs of needle-nose pliers, bend the antenna plate according to the illustration and measurement shown. ANTENNA 15 mm (0.6 in.) 8 mm (0.3 in.) SCALE NEEDLE-NOSE PLIERS PLATE 8 of 21 23. Measure the antenna cable as shown. Attach the three foam cushion tapes to the antenna cable in the measurement shown.
Page 9
27. Route the antenna cable under the roof liner towards the driver’s side of vehicle, and down along the vehicle harness. Be careful not to crease the roof liner. ROOF LINER VEHICLE HARNESS ANTENNA CABLE 28. Continue routing the antenna cable between the front pillar and the dashboard.
Page 10
31. Secure the antenna cable to the vehicle harness with a wire tie. Secure the wire tie between the vehicle harness branching points. WIRE TIE VEHICLE HARNESS BRANCHING POINTS Installing the Control Unit Bracket 32. Locate the small square hole next to the small round hole in the dashboard support bracket.
Page 11
35. Route the engine starter harness 7-pin connectors up the steering column and to the ignition switch. Unplug the white vehicle 7-pin connector. Plug the white engine starter harness 7-pin connectors into the white vehicle 7-pin connectors. ENGINE STARTER HARNESS 7-PIN CONNECTOR (white)
Page 12
39. Wrap the vehicle 7-pin connector with one foam cushion tape, then place the vehicle 7-pin connector into the gap of the column. VEHICLE 7-PIN CONNECTOR (brown) (Squeeze into this area.) FOAM CUSHION TAPE VEHICLE 7-PIN VEHICLE CONNECTOR BRACKET 40. Secure the engine starter harness to the vehicle harness with four wire ties in the areas shown.
Page 13
45. With driver's dashboard under cover: Measure the indicated dimension on the instrument panel and mark with a felt-tip pen and a center punch. INSTRUMENT PANEL View from below 12 mm (0.5 in.) FELT-TIP PEN FRONT 6 mm (0.2 in.) Drill a 3 mm hole and then a 7 mm hole at the marked position of the instrument panel.
Page 14
48. Disconnect the vehicle 42-pin, 4-pin and 2-pin connectors. VEHICLE 4-PIN CONNECTOR VEHICLE 42-PIN CONNECTOR FUSE BOX FUSE BOX LOCK VEHICLE 42-PIN CONNECTOR 14 of 21 49. Plug the engine starter harness 4-pin and 2-pin connectors into the fuse box. NOTICE Check that the engine starter harness 4-pin and 2-pin connectors are connected to the fuse box VEHICLE 2-PIN...
Page 15
51. Connect the engine starter harness 18-pin connectors with each other and secure them with a wire tie to the vehicle harness. 52. Unplug the white vehicle 14-pin connector at the front lower pillar behind the fuse box, and plug the engine starter harness 14-pin connectors in between.
Page 16
Installing the Control Unit 55. Connect the antenna cable terminal and the engine starter harness 18-pin connector to the control unit. ANTENNA CABLE TERMINAL (Connect first.) CONTROL UNIT ENGINE STARTER BRACKET HARNESS 18-PIN CONNECTOR 56. Install the control unit on the control unit bracket. 57.
REMOTE ENGINE STARTER REGISTRATION Acquire the PCM code from ISIS. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to the ON (II) position. Start the HDS, and click the car icon. Input the VIN and other required information into the HDS, then click the check button.
Page 18
A REMARKS message will display. Click the check button. “REMARKS” message Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button. Select “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.” 18 of 21 The following message will display: Obtain PCM- code (IMMOBILIZER PCM CODE) from iN.
Page 19
11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click the check button. "Registration" message 12. The following message will display: Check that the engine can be started by the Transmitter. Click the check button.
FUNCTION CHECK Operating Conditions • The hood is closed. • Shift lever is in Park. • The key is not in the ignition switch. • All doors and trunk are closed and locked. Inspection Within 1 second, press the command button and then the start button on the transmitter. The engine should start if all operating conditions are met.