Table of Contents
Advertisement
Quick Links
Cisco Communication Media Module for
Catalyst 6500 Series Switch and Cisco 7600
Series Router Installation and Verification Note
Product Number: WS-SVC-CMM
Last Updated: March 23, 2009
This publication contains the procedures for installing and configuring the Catalyst 6500 series switch
and Cisco 7600 series router Communication Media Module (CMM). Installation and configuration
procedures are provided for the following CMM port adapters:
6-port T1 port adapter (WS-SVC-CMM-6T1)
•
6-port E1 port adapter (WS-SVC-CMM-6E1)
•
24-port FXS port adapter (WS-SVC-CMM-24FXS)
•
•
128-port ad-hoc conferencing and transcoding (ACT) port adapter (WS-SVC-CMM-ACT)
Except where specifically differentiated, the term "Catalyst 6500 series switches" includes both the
Note
Catalyst 6500 series switches and the Catalyst 6000 series switches.
Note
Throughout this publication, except where specifically differentiated, the term supervisor engine refers
to Supervisor Engine 1, Supervisor Engine 2, Supervisor Engine 720, and the Supervisor Engine 32.
Additionally, the term Multilayer Switch Feature Card (MSFC) refers to MSFC, MSFC2, and MSFC3.
Americas Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Advertisement
Table of Contents
Related Manuals for Cisco 6500-E
Summary of Contents for Cisco 6500-E
- Page 1 Last Updated: March 23, 2009 This publication contains the procedures for installing and configuring the Catalyst 6500 series switch and Cisco 7600 series router Communication Media Module (CMM). Installation and configuration procedures are provided for the following CMM port adapters: 6-port T1 port adapter (WS-SVC-CMM-6T1) •...
-
Page 2: Table Of Contents
• a blank filler plate in the right slot. REAR MODULE STATUS LED—Table 2 describes the REAR MODULE STATUS LED operation. • Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 3: Front Panel Descriptions
1. Enter the show environment temperature mod command to display the temperature of each of the four sensors on the module. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 4: 6-Port T1 And E1 Port Adapters
“RJ-45 Port Connector and Cabling Specifications” section on page 25 • for details. Figure 2 shows the front panels of the 6-port T1 and E1 port adapters. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 5: 24-Port Fxs Port Adapter
Statement 1031 Figure 3 shows the front panel of the 24-port FXS port adapter. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 6: Requirements
Port adapter is not located by the system. Requirements These sections describe the hardware and software requirements: Hardware Requirements, page 7 • Software Requirements, page 7 • Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 7: Safety Overview
Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device. Statement 1071 SAVE THESE INSTRUCTIONS Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... - Page 8 Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement 1001 Warning Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Statement 1036 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
- Page 9 LAN and WAN ports both use RJ-45 connectors. Use caution when connecting cables. Statement 1021 Warning To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
-
Page 10: Required Tools
Removing the Module, page 17 • Installing the Module This section describes how to install the module into the Catalyst 6500 series switch or the Cisco 7600 series router. All modules, including the supervisor engine (if you have redundant supervisor engines), support hot Note swapping. - Page 11 45 degrees with respect to the module faceplate. (See Figure Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
- Page 12 EMI gasket INPUT OUTPU T FAIL INPUT OUTPU T FAIL WS-C 6500- SFM SWIT CH FABR IC MDL Ejector lever fully extended Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
- Page 13 While pressing down, simultaneously close the left and right ejector levers to fully seat the module in the backplane connector. The ejector levers are fully closed when they are flush with the module faceplate. (See Figure Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
- Page 14 8.) Make sure that you align the sides of the module carrier with the slot guides on the top and bottom of the slot. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
- Page 15 0.040 inches (1 mm) to create a small gap between the module’s EMI gasket and the module adjacent to it. (See Figure Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
- Page 16 While pressing on the ejector levers, simultaneously close them to fully seat the module in the backplane connector. The ejector levers are fully closed when they are flush with the module faceplate. (See Figure 10.) Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
-
Page 17: Removing The Module
This completes the module installation procedure. Removing the Module This section describes how to remove the module from a Catalyst 6500 series switch or the Cisco 7600 series router. During this procedure, wear grounding wrist straps to avoid ESD damage to the module. Do not directly Caution touch the backplane with your hand or any metal tool, or you could shock yourself. - Page 18 Do not operate the system unless all cards, faceplates, front covers, and rear covers are in place. Statement 1029 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
-
Page 19: Removing And Replacing Port Adapters
Step 7 Place the removed port adapter in an antistatic bag. Step 8 If leaving an empty slot, install a blank filler plate. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 20: Removing And Replacing Port Adapters
Statement 1029 To install the module into the Catalyst 6500 series switch or the Cisco 7600 series router, see the Step 9 “Installing the Module” section on page... - Page 21 (6) Port adapter connectors (6) Phillips screw mounting posts (6) Slot 1 Slot 2 Slot 3 Phillips screw access holes (6) Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
- Page 22 Use care not to damage the connectors on the port adapter. If you damage a connector, you will have to Caution return the port adapter to Cisco for repair. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
- Page 23 13, note the location of the two slot 4 Phillips screw mounting posts. Remove the two Phillips Step 3 screws that secure the right-hand side of the port adapter. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
- Page 24 Use care not to damage the connectors on the port adapter. If you damage a connector, you will have to Caution return the port adapter to Cisco for repair. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note...
-
Page 25: Verifying The Installation
Statement 1036 Never touch uninsulated telephone wires or terminals unless the telephone line has been Warning disconnected at the network interface. Statement 1037 Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 26: Rj-45 Port Connector And Cabling Specifications
Not connected Table 6 lists the pinouts for the RJ-45 port connector, not the pinouts of the cable connecting to the port. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 27: Rj-21 Port Connector And Cabling Specifications
16. A pinout for the module’s RJ-21 connector is provided in Table Figure 15 RJ-21 Telco Interface 90-Degree Cable Connector Figure 16 RJ-21 Telco Interface 180-Degree Cable Connector Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 28: Accessing The Port Adapter Ports
For example, to configure the first port on a 6-port T1 port adapter that is installed in slot 2, specify T1 2/0. For the second port, specify T1 2/1, and so on. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 29: Configuring The Port Adapter Ports
This system clock could be a module internal clock or the Rx clock from the port that is configured as the primary clock source. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 30: Disaster Recovery For Module Software Upgrades
Disaster Recovery for Supervisor Engines Running Cisco IOS Software, page 31 If the CMM image fails to load properly, a crash information file is generated and then saved in the CMM bootflash. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 31: Disaster Recovery For Module Software Upgrades
Enter the copy tftp [device] command to copy the golden image for the CMM to the supervisor engine flash memory where [device] can be any flash file system on the supervisor engine. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 32: Password Recovery
Password Recovery Procedure for the Catalyst 6500/6000 Step 5 SeriesSwitches Running Cisco IOS System Software to recover the password for the CMM. Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... -
Page 33: Regulatory Standards Compliance
Cisco documents, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html Cisco Communication Media Module for Catalyst 6500 Series Switch and Cisco 7600 Series Router Installation and Verification Note... - Page 34 Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks. Third-party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company.