Page 1 Cisco SCE 2000 4xGBE Installation and Configuration Guide Version 3.0 OL-7824-04 Corporate Headquarters C isco Sys te ms , Inc . 1 70 W es t Tas ma n D r i ve Sa n Jose , C A 9 513 4-1 706 U S A h t t p : / /w w w .c i s c o .co m...
Page 2 • Turn the television or radio antenna until the interference stops. • Move the equipment to one side or the other of the television or radio. • Move the equipment farther away from the television or radio. • Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)
Page 3: Table Of Contents
Network Management 1-5 Subscriber Management 1-5 Collection 1-5 Service Configuration Management 1-5 Introduction to the SCE Platform 2-1 The SCE Platform 2-1 Front Panel 2-2 OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide C O N T E N T S...
Page 4 Powering Down the Power Supply Unit and Disconnecting Input Power 4-15 Removing the Power Supply Unit 4-16 Replacing the Power Supply Unit 4-17 Reconnecting the Power 4-17 Fan Module Overview 4-20 Cisco SCE 2000 4xGBE Installation and Configuration Guide OL-7824-04...
Page 5 CLI Commands 6-11 Loading and Activating a Service Control Application 6-14 Basic SCE 2000 Platform Operations 7-1 Starting the SCE 2000 Platform 7-1 Checking Conditions Prior to System Startup 7-1 OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Contents...
Page 6 The External Optical Bypass Module Front Panel A-3 Installing the External Bypass Module A-3 Installing the Module in a Rack A-4 Cabling the External Optical Bypass Module A-4 Specifications A-7 Index I-1 Cisco SCE 2000 4xGBE Installation and Configuration Guide OL-7824-04...
Page 7: Preface
Preface This preface describes who should read the SCE 2000 4xGBE Installation and Configuration Guide, how it is organized, and its document conventions. Document Revision History Cisco Service Control Release Release 3.0 ESCRIPTION OF Added the following new features: Redundant Management (Mng) port.
Page 8: Organization
Organization Organization The major sections of this guide are as follows: Chapter Cisco SCE 2000 4xGBE Installation and Configuration Guide Title Description Introduction This chapter provides a brief introduction to Cisco Service Control. Overview (on page 2-1) This chapter provides a hardware overview of the SCE 2000 platform.
Page 9: Related Publications
Note on the World Wide Web at available at the following URL: (http://www.cisco.com/public/countries_languages.shtml). For initial installation and startup information, refer to the SCE 2000 4xGBE Quick Start • Guide. For international agency compliance, safety, and statutory information for wide-area •...
Page 10 Warnings use the following conventions: Warning Means reader be warned. You are capable of doing something that might result in bodily injury. Cisco SCE 2000 4xGBE Installation and Configuration Guide viii Optional alternative keywords are grouped in brackets and separated by vertical bars.
Page 11: Obtaining Documentation
Preface Obtaining Documentation The following sections provide sources for obtaining documentation from Cisco Systems. World Wide Web You can access the most current Cisco documentation on the World Wide Web at the following sites: • http://www.cisco.com http://www-china.cisco.com • http://www-europe.cisco.com •...
Page 12: Documentation Feedback
Cisco. To access Cisco.com, go to the following website: http://www.cisco.com Cisco SCE 2000 4xGBE Installation and Configuration Guide Cisco.com (on page x) as a starting point for all technical assistance. Customers...
Page 13: Technical Assistance Center
No workaround is available. • P2—Your production network is severely degraded, affecting significant aspects of your business operations. No workaround is available. OL-7824-04 Cisco.com (on page x), go to the following website: Cisco SCE 2000 4xGBE Installation and Configuration Guide Obtaining Technical Assistance...
Page 15: Overview
Cisco provides Service Control solutions that allow the service provider to bridge this gap. OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide C H A P T E R 1...
Page 16: Service Control For Broadband Service Providers
Programmability—The ability to quickly add new protocols and easily adapt to new • services and applications in the ever-changing service provider environment. Programmability is achieved using the Cisco Service Modeling Language (SML). Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 1 Overview OL-7824-04...
Page 17: The Sce Platform
Programmable system core for flexible reporting and bandwidth control • Transparent network and BSS/OSS integration into existing networks • Subscriber awareness that relates traffic and usage to specific customers • OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide The SCE Platform...
Page 18: Management And Collection
Service Control management • These management interfaces are designed to comply with common management standards and to easily integrate with existing OSS infrastructure. Figure 1-2: Service Control Management Infrastructure Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 1 Overview OL-7824-04...
Page 19: Network Management
Service Control provides an easy-to-use GUI to edit and create these files, as well as a complete set of APIs to automate their creation. OL-7824-04 Service Configuration Management Cisco SCE 2000 4xGBE Installation and Configuration Guide...
Page 21: Introduction To The Sce Platform
Introduction to the SCE Platform This chapter provides an introduction to the SCE 2000 4xGBE Platform, the Service Control hardware component. This chapter contains the following sections: • The SCE Platform 2-1 • Front Panel • Back Panel • Checking the Shipping Container Contents •...
Page 22: Front Panel
Figure 2-1: SCE 2000 Front Panel Table 2-2 Port Mng1/ Mng2 Console GBE ports 1-4 4 Cisco SCE 2000 4xGBE Installation and Configuration Guide SCE 2000 Ports Quantity Description 10/100/1000 Ethernet RJ-45 ports for management of the SCE 2000. CLI designation: interface Management 0/1, 0/2.
Page 23 Unlit — indicates that the port link is down • Rx Flashing Green — indicates that there are incoming packets • Tx Flashing Green — indicates that there are outgoing packets Cisco SCE 2000 4xGBE Installation and Configuration Guide Front Panel...
Page 24: Back Panel
The rear panels of both the AC- and DC-powered SCE 2000 platforms are shown in the following pair of figures. Figure 2-2: SCE 2000 Back Panel: AC Power Cisco SCE 2000 4xGBE Installation and Configuration Guide Description The Mng port LEDs indicate the operational status of the SCE 2000 out-of-band LAN-based management port, as follows: •...
Page 25: Checking The Shipping Container Contents
Use the SCE 2000 Component List to check the contents of the SCE 2000 platform shipping container. Do not discard the shipping container. You need the container if you move or ship the SCE 2000 platform in the future. Cisco SCE 2000 4xGBE Installation and Configuration Guide OL-7824-04...
Page 26: Sce 2000 Component List
If you ordered documentation and did not receive it, we will ship the documents to you within 24 hours. To order documents, contact a customer service representative. Cisco SCE 2000 4xGBE Installation and Configuration Guide SCE 2000 Component List Description SCE 2020 4xGBE platform configured with either AC or DC power supplies.
Page 27: Sce 2000 Installation Checklist
System power turned on System boot complete (SYSTEM–UP LED is on) Correct hardware configuration displayed after system banner appears OL-7824-04 SCE 2000 Installation Checklist Setup Command Parameters Cisco SCE 2000 4xGBE Installation and Configuration Guide SCE 2000 Installation Checklist Verified Date...
Page 29: Topology
Functionality — Will the system be used solely to monitor traffic flow, with report • functionality only, or will it be used for traffic flow control, with enforcement as well as report functionality? OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide C H A P T E R 3...
Page 30: Functionality
SCE 2000 fail. If only preservation of the network links is required, and uninterrupted functionality of the SCE 2000 is not required, a single SCE 2000 is sufficient. Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 3 Topology...
Page 31: Link Continuity
In Cutoff the physical interface is blocked, enabling the network device connected to the SCE 2000 to sense that the link is down. OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Topology Considerations...
Page 32: Physical Topologies
Figure 3-1: Single SCE Platform Single Link: In-line Topology When configuring the SCE 2000, an inline installation is referred to as “inline” connection mode. Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 3 Topology...
Page 33 Figure 3-2: Single SCE Platform Dual Link Inline Topology This topology supports both monitoring and control functionality, and is referred to as “inline” connection mode. Cisco SCE 2000 4xGBE Installation and Configuration Guide OL-7824-04...
Page 34 Note that in an optical splitter topology, the SCE 2000 only enables traffic monitoring functionality. When implementing receive-only topologies with a switch, the switch must support SPAN functionality Note that includes separation between ingress and egress traffic and multiple SPAN-ports destinations. Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 3 Topology OL-7824-04...
Page 35 Figure 3-4: Single SCE Platform Dual Link Receive-Only Topology When implementing receive-only topologies with a switch, the switch must support SPAN functionality that includes separation between ingress and egress traffic and multiple SPAN-ports destinations. OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Physical Topologies...
Page 36: Two Cascaded Sce 2000S For Dual Links
The two SCE 2000s are simultaneously aware of the subscriber contexts, and subscriber • states are constantly exchanged between them, such that if the primary SCE 2000 fails, the secondary can take over with minimum state loss. Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 3 Topology OL-7824-04...
Page 37: Topology-Related Parameters
Inline — The SCE 2000 resides on the data link between the subscriber side and the • network side, thus both receiving and transmitting packets. OL-7824-04 Connection Mode Parameter (on page 3-10)). On-Failure Mode Parameter Cisco SCE 2000 4xGBE Installation and Configuration Guide Physical Topologies (on page 3-9)): Physically Connected Links Priority (on page 3-10)).
Page 38: Physically Connected Links Parameter
SCE 2000 fails, or whether traffic flow should continue across the link in spite of platform failure. Cutoff mode is required for the following: • Redundant inline topology. • Cisco SCE 2000 4xGBE Installation and Configuration Guide 3-10 Chapter 3 Topology OL-7824-04...
Page 39 Non-redundant inline topology if value-added services are crucial and are more important • than maintaining connectivity. • Bypass mode is required for the following: Non-redundant inline topology if connectivity is crucial. • OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Physical Topologies 3-11...
Page 41: Installation And Maintenance
The section contains the following topics: Tools and Parts Required • Site Requirement Guidelines • OL-7824-04 4-14 4-20 4-22 (on page 4-2) (on page 4-3) Cisco SCE 2000 4xGBE Installation and Configuration Guide C H A P T E R 4...
Page 42: Tools And Parts Required
Rack-mounting kit (optional) • A new AC-input or DC-input power supply • • A new fan module Cisco SCE 2000 4xGBE Installation and Configuration Guide SCE 2000 Dimensions Measurement 3.47 inches (9.5 cm) 17.4 inches (4.43 cm) 18 inches (4.6 cm)
Page 43: Site Requirement Guidelines
SCE 2000 Environmental Requirements Acceptable Range nominal 41°F to 104°F (5°C to 40°C) 23°F to 131°F (-5°C to +55°C) 5% to 95% (non-condensing) 683 BTU/hour Cisco SCE 2000 4xGBE Installation and Configuration Guide Preparing to Install the SCE 2000 Platform...
Page 44: Installing The Sce 2000 Platform
Installing the Rack-Mounting a • Attaching a Chassis Ground Connection • Cisco SCE 2000 4xGBE Installation and Configuration Guide SCE 2000 Approvals Specifications Specification • CE Mark • EMISSIONS: FCC Part 15 CFR 47 Class A, EN 55022 Class A, CISPR22 Class A, VCCI Class A, AS/NZS CISPR22 Class A •...
Page 45: Installation Precautions
Place the SCE 2000 platform on the tabletop or workbench. Step 2 OL-7824-04 Installing the SCE 2000 Platform Site Requirement Guidelines (on page 4-10) for instructions). Cisco SCE 2000 4xGBE Installation and Configuration Guide (on page 4-3) and the Site Airflow (on page Attaching a Installation Precautions...
Page 46: Rack-Mounting A Sce 2000 Platform
Because the inlet and exhaust ports (vents) for cooling air are located at both sides of the chassis, respectively, multiple SCE 2000s can be stacked in a rack with no vertical clearance. Cisco SCE 2000 4xGBE Installation and Configuration Guide Attaching a Chassis Ground Connection...
Page 47: Attaching The Brackets To The Sce
(on page 4-2) for a listing of the parts and tools required for installing the Platform" on page 4-6). "Mounting the System to the Cisco SCE 2000 4xGBE Installation and Configuration Guide Installing the SCE 2000 Platform Rack-Mounting a SCE 2000...
Page 48: Attaching The Crossrail Supports To The Rack
Repeat steps 2 through 4 on the other side of the rack, keeping the brackets flush against the posts Step 5 and parallel to the supporting bracket on first side of the rack. Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 4 Installation and Maintenance...
Page 49: Mounting The System To The Rack
A rack with both front and back posts will have the crossrail supports installed. Slide the SCE 2000 onto these crossrails and push it all the way back. Figure 4-8: Sliding the SCE 2000 into the Rack OL-7824-04 Installing the SCE 2000 Platform Cisco SCE 2000 4xGBE Installation and Configuration Guide...
Page 50: Attaching A Chassis Ground Connection
Step 2 On the Rear panel of the SCE 2000, locate the chassis grounding connector (refer to the appropriate figure for an AC- or DC-powered SCE 2000 below). Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-10 Chapter 4 Installation and Maintenance...
Page 51 Figure 4-11: Grounding the Unit (DC) This completes the procedure for installing the SCE 2000 chassis. Proceed to the next section, Connecting to the Power Supply, to continue the installation. Cisco SCE 2000 4xGBE Installation and Configuration Guide OL-7824-04 4-11...
Page 52: Power Supply Overview
The handle of the AC unit is at the bottom of the unit. Figure 4-12: AC Power Module The handle of the DC unit is at the top of the unit. Figure 4-13: DC Power Module Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-12 Chapter 4 Installation and Maintenance...
Page 53: Leds
Power Supply Unit Condition Corresponding power supply unit is present and functioning normally Corresponding power supply unit present, but malfunctioning Corresponding power supply unit is either not present or has failed. Cisco SCE 2000 4xGBE Installation and Configuration Guide Power Supply Overview 4-13...
Page 54: Power Supply Specifications
• Replacing the Power Supply Unit • Reconnecting the Power • Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-14 SCE 2000 Power Supply Specifications 200W maximum 100 to 240 VAC Rated for 4.5A when Vin = 100 VAC or 2A when Vin = 200 VAC...
Page 55: Powering Down The Power Supply Unit And Disconnecting Input Power
This completes the procedure for powering down an AC-input power supply unit on a SCE 2000 platform. Proceed to OL-7824-04 Removing and Replacing a Power Supply Unit (on page 4-15) Removing the Power Supply Unit (on page 4-16). Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-15...
Page 56: Removing The Power Supply Unit
Grasp the power supply handle and pull the power supply from the router. This completes the procedure for removing the power supply from a SCE 2000 platform. Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-16 Removing the Power Supply Unit (on page 4-16).
Page 57: Replacing The Power Supply Unit
The following sections describe how to reconnect the AC or DC power: Reconnecting AC-Input Power Supply Unit • Reconnecting DC-Input Power Supply Unit • OL-7824-04 Removing and Replacing a Power Supply Unit (on page 4-18) (on page 4-19) Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-17...
Page 58: Reconnecting Ac-Input Power Supply Unit
Ensure that the power supply is properly aligned and the installation screw is tightened. Step 5 This completes the steps for reconnecting the AC-input power supply to the SCE 2000 platform. Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-18 Chapter 4...
Page 59: Reconnecting Dc-Input Power Supply Unit
Make certain the lead color coding you choose for the DC-input power supply matches lead color coding used at the DC power source. OL-7824-04 Removing and Replacing a Power Supply Unit Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-19...
Page 60: Fan Module Overview
The following sections explain how to remove and replace a fan module in a SCE 2000 platform: Removing the Fan Module • Replacing the Fan Module • Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-20 Chapter 4 (on page 4-21) (on page 4-21)
Page 61: Removing The Fan Module
Gently, but firmly, slide the module into the chassis until its faceplate is flush with the chassis rear Step 3 panel. Figure 4-17: Inserting the Fan Module OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Fan Module Overview 4-21...
Page 62: Replacing The Battery
There is danger of explosion if the lithium battery is incorrectly replaced. Replace only with the same Warning or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Cisco SCE 2000 4xGBE Installation and Configuration Guide 4-22 Chapter 4 Installation and Maintenance...
Page 63: Connecting The Management Interfaces And Performing Initial System Configuration
When the initial connection is established, the setup utility will run automatically, prompting you to perform the initial system configuration. OL-7824-04 Installing a Cascaded System (on page 6-10). 5-25 Cisco SCE 2000 4xGBE Installation and Configuration Guide C H A P T E R 5...
Page 64: Setting Up The Local Console
Would you like to continue with the System Configuration Dialog? [yes/no]: y Step 5 Type y and press Enter. The system configuration dialog begins. Cisco SCE 2000 4xGBE Installation and Configuration Guide Connecting the Management Interfaces and Performing Initial System Configuration --- System Configuration Dialog --- OL-7824-04...
Page 65: Initial System Configuration
Admin level password. Character string from 4-100 characters beginning with an alpha character. Root level password. Character string from 4-100 characters beginning with an alpha character. Enable or disable password encryption? Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration...
Page 66 SNMP agent status GET community names SET community names trap managers (maximum Cisco SCE 2000 4xGBE Installation and Configuration Guide Connecting the Management Interfaces and Performing Initial System Configuration Definition Standard time zone abbreviation and minutes offset from UTC. Current local time and date. Use the format: 00:00:00 1 January 2002 Set the status of the SNTP broadcast client.
Page 67: Index
After a reboot due to a failure, should the SCE 2000 remain in a Failure status or move to operational status provided no other problem was detected? Sorry, Skipping is not allowed at this stage Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration .”...
Page 68: Step 1: Configuring Initial Settings
Enter IP address [10.1.1.201]:10.1.5.109 Enter IP subnet mask:255.255.0.0 Enter IP address of default gateway [10.1.1.3]: Cisco SCE 2000 4xGBE Installation and Configuration Guide Connecting the Management Interfaces and Performing Initial System Configuration OL-7824-04...
Page 69: Step 2: Configuring The Hostname
Maximum length — 100 characters Begin with an alpha character • May contain only printable characters • Note Passwords are case sensitive. Note The default password for all levels is “cisco”. OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration...
Page 70: Step 4: Configuring Time Settings
Unlike all other settings defined in the system configuration, setting the time is done immediately and not at the end of the setup process. Cisco SCE 2000 4xGBE Installation and Configuration Guide Connecting the Management Interfaces and Performing Initial System Configuration...
Page 71 Enter Would you like to configure SNTP unicast servers? [no]: y Enter IP address or hostname of SNTP unicast server: 10.1.1.1 OL-7824-04 (on page 5-10). Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration Step 5:...
Page 72: Step 5: Configuring The Dns Settings
Step 4 Type the IP address of the primary domain name server and press Enter. Enter Primary DNS IP address: Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-10 Connecting the Management Interfaces and Performing Initial System Configuration (on page 5-11). The rest of the dialog is not presented, as it is...
Page 73: Step 6: Configuring The Rdr Formatter Destination
Type the TCP port number of the RDR-formatter destination and press Enter. Note that there is no default for this parameter. Enter RDR-formatter destination’s TCP port number: OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration 5-11...
Page 74: Step 7: Configuring Access Control Lists (Acls)
Individual IP address — Type the desired IP address, then enter the wildcard bits 0.0.0.0. • Each individual IP address can be configured to be permitted or denied access. Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-12 Connecting the Management Interfaces and Performing Initial System Configuration...
Page 75: Order Of Entries
Indicate whether this entry is permitted access or denied access. To permit access press Enter. • OL-7824-04 IP address/Wildcard bit examples Wildcard bits 0.0.0.255 0.0.0.63 0.0.0.0 Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration Range 10.1.1.0–10.1.1.255 10.1.1.0–10.1.1.63 10.1.1.0 (individual entry) 5-13...
Page 76 Type the number of the ACL to be assigned to the Telnet interface and press Enter. To accept the default ACL, press Enter. Enter Telnet access-class [0]: 2 Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-14 Connecting the Management Interfaces and Performing Initial System Configuration Entry Formats (on page 5-12).)
Page 77 Would you like to enter the Access lists configuration menu? [no]: y Would you like to create new Access lists or modify existing lists? [no]: Enter IP access-class [0]: 10 Enter Telnet access-class [0]: 22 OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration 5-15...
Page 78: Step 8: Configuring Snmp
Type the SNMP SET community name and press Enter. The SNMP agent that resides inside the SCE 2000 will respond only to SET requests that use this community string. Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-16 Connecting the Management Interfaces and Performing Initial System Configuration...
Page 79 To enable the Authentication Failure trap, type y and press Enter. • Enable the ‘Authentication Failure’ trap [no]: Step 15 Configure the SCE enterprise trap status. To disable the SCE enterprise traps, type n press Enter. • OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration 5-17...
Page 80: Step 9: Configuring The Topology-Dependent Parameters
Connection mode — Can be either of the following, depending on the physical installation of the SCE 2000. Inline • Receive-only • Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-18 Connecting the Management Interfaces and Performing Initial System Configuration Topology (on page 3-1) for a OL-7824-04...
Page 81 2000 returns to full operational mode after abnormal (not user-requested) boot, or stays in non-operational mode, in which the SCE 2000 behaves as in failure mode. This parameter can be set to one of the following: • Operational • Non-operational OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration 5-19...
Page 82 Enter On-failure behavior: 1- bypass 2- cutoff Enter your choice [1]: Step 7 Specify the status of the SCE 2000 after abnormal boot. Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-20 Connecting the Management Interfaces and Performing Initial System Configuration OL-7824-04...
Page 83 Enter your choice [1]: 1 Enter admin status of the SCE after abnormal boot: 1- Operational 2- Not-Operational Enter your choice [1]: 1 Data collection for the system configuration is completed. OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration 5-21...
Page 84: Step 10: Completing And Saving The Configuration
If any errors are detected, you may choose to view them. Step 2 Press Enter. Found errors in the new configuration, would you like to view them? [yes]: Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-22 Connecting the Management Interfaces and Performing Initial System Configuration OL-7824-04...
Page 85 Note that no confirmation is requested for the decision to abort the setup. Had there been no errors, confirmation would have been requested before aborting. Data collection for the system configuration is completed. OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Initial System Configuration 5-23...
Page 86 Apply and Save this configuration? [yes/no]: n The changes you have just entered would be discarded, are you sure? [yes/no]:y Setup procedure aborted, no configuration changes made. Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-24 Connecting the Management Interfaces and Performing Initial System Configuration OL-7824-04...
Page 87: Connecting The Management Interface
Carefully pull the plug out of the socket. If the management port Link LED on the SCE 2000 still does not light, verify that the cable is OL-7824-04 Connecting the Management Interface (on page 5-25) (on page 5-26) Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-25...
Page 88: Verifying Management Interface Connectivity
64 bytes from host (10.1.1.201): icmp_seq=0. time=0. ms 64 bytes from host (10.1.1.201): icmp_seq=1. time=0. ms 64 bytes from host (10.1.1.201): icmp_seq=2. time=0. ms Cisco SCE 2000 4xGBE Installation and Configuration Guide 5-26 Connecting the Management Interfaces and Performing Initial System Configuration...
Page 89 Connecting the Management Interfaces and Performing Initial System Configuration Connecting the Management Interface 64 bytes from host (10.1.1.201): icmp_seq=3. time=0. ms ----10.1.1.201 PING Statistics---- 4 packets transmitted, 4 packets received, 0% packet loss round-trip (ms) min/avg/max = 0/0/0 Cisco SCE 2000 4xGBE Installation and Configuration Guide OL-7824-04 5-27...
Page 91: Cabling The Line Ports And Completing The Installation
Installing a Cascaded System (on page 6-10). (on page A-4) for complete instructions. 6-10 (on page 6-2) (on page 6-6) (on page 6-7) Cisco SCE 2000 4xGBE Installation and Configuration Guide C H A P T E R 6 6-14...
Page 92: Cabling Diagrams
SCE 2000 while port 2 or port 4 is used for connecting to the network element that is deployed on the network side of the SCE 2000. Inline topology requires both Receive and Transmit fibers Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 6 Cabling the Line Ports and Completing the Installation Counters"...
Page 93 Port 1: Link 1, Subscriber side • Port 2: Link 1, Network side Port 3: Link 2, Subscriber side • Port 4: Link 2, Network side • OL-7824-04 Connecting the line ports to the network Cisco SCE 2000 4xGBE Installation and Configuration Guide...
Page 94 Figure 6-3: Cabling Diagram: Dual Link One SCE 2000 Inline Figure 6-4: Cabling Diagram: Dual Link One SCE 2000 Receive-only Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 6 Cabling the Line Ports and Completing the Installation...
Page 95 Port 3: Cascade, connect to Port 4 in SCE 2000 #1 • Port 4: Cascade, connect to Port 3 in SCE 2000 #1 • OL-7824-04 Installing a Cascaded System (on page 6-10). Cisco SCE 2000 4xGBE Installation and Configuration Guide Connecting the line ports to the network...
Page 96: Configuring The Gbe Interface Parameters
(receive-only topology) If you change any parameters, you must save the new configuration settings. Note Type copy running-config startup-config, and press Enter Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 6 Cabling the Line Ports and Completing the Installation OL-7824-04...
Page 97: Connecting The Gbe Line Interface Ports
Multimode OR 1310nm Single Mode. OL-7824-04 (on page 6-2) to find the appropriate cabling diagram for the topology of your (on page A-4) for complete instructions. Cisco SCE 2000 4xGBE Installation and Configuration Guide Connecting the line ports to the network...
Page 98: Cabling The Gbe Port
Verify that the link LED is green. If the link LED does not light, try removing the network cable plug and reinserting it firmly into the module socket. Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 6 Cabling the Line Ports and Completing the Installation...
Page 99: Testing Connectivity: Examining Link Leds And Counters
The following example displays a system response. SCE 2000#show interface GigabitEthernet 0/1 Auto negotiation configured: Enabled Actual Status: Link is on Auto negotiation: Enabled Bandwidth: 100000Kbps Burst-size: 50000bytes OL-7824-04 Connecting the line ports to the network Cisco SCE 2000 4xGBE Installation and Configuration Guide...
Page 100: Installing A Cascaded System
Install both SCE 2000 platforms, power them up, and perform the initial system configuration. (See Installation and Maintenance Performing Initial System Configuration Cisco SCE 2000 4xGBE Installation and Configuration Guide 6-10 Chapter 6 Cabling the Line Ports and Completing the Installation...
Page 101: Cli Commands
Link Mode (on page 6-13).) Dual Link: Two Dual Link: Two Link Mode (on page 6-13).) Cisco SCE 2000 4xGBE Installation and Configuration Guide Installing a Cascaded System Connecting the Management 2000s Topology (on page 6-5).) (on page 6-11).) Monitoring the System (on page 6-14).)
Page 102: Configuring The Connection Mode
SCE 2000 platform if a failure occurs is also bypass. SCE 2000(config if)# connection-mode inline-cascade physically-connected- links link-0 priority secondary on-failure bypass Cisco SCE 2000 4xGBE Installation and Configuration Guide 6-12 Chapter 6 Cabling the Line Ports and Completing the Installation...
Page 103: Link Mode
The default link mode is forwarding. When other link modes are selected, active service • control is not available and any service control configuration will not be applicable. OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide Installing a Cascaded System 6-13...
Page 104: Loading And Activating A Service Control Application
• Activating the application. • Configuring the application. • Cisco SCE 2000 4xGBE Installation and Configuration Guide 6-14 Chapter 6 prompt, type show interface linecard 0 connection-mode prompt, type show interface linecard 0 link mode and press prompt, type show interface linecard 0 physically-...
Page 105 For further details, refer to the following documentation: Service Control Application Suite for Broadband User Guide • • Service Control Application Suite for Broadband Reference Guide OL-7824-04 Loading and Activating a Service Control Application Cisco SCE 2000 4xGBE Installation and Configuration Guide 6-15...
Page 107: Basic Sce 2000 Platform Operations
Direct connection to local console (CON port) • Remote management station via the LAN (Mng port) • OL-7824-04 (on page 7-1) (on page 7-2) Cisco SCE 2000 4xGBE Installation and Configuration Guide C H A P T E R 7...
Page 108: Starting The System And Observing Initial Conditions
You do not have to configure the interfaces immediately. If the system does not complete each of the steps in the startup procedure, proceed to Chapter 7, Troubleshooting Cisco SCE 2000 4xGBE Installation and Configuration Guide (on page 7-2). (on page 8-1) for troubleshooting recommendations and procedures.
Page 109: Final Tests
If there are “Total error messages” or “Total fatal messages”, use the show logger device User-File-Log command to display details about the errors. OL-7824-04 Starting the SCE 2000 Platform (on page 7-3) (on page 7-3) Cisco SCE 2000 4xGBE Installation and Configuration Guide...
Page 110: Managing Sce 2000 Configurations
FastEthernet 0/1 interface FastEthernet 0/2 exit line vty 0 4 no timeout exit SCE 2000# Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 7 (on page 7-4) (on page 7-6) (on page 7-8) February 2002 Basic SCE 2000 Platform Operations...
Page 111 SCE 2000 uptime is 21 minutes, 37 seconds SCE 2000# OL-7824-04 : 0x0075 : 0x1808 : 0x1708 : 0x0077 : 0x1721 : 0x0025 : 0x0176 : G001 : 2.1.0 : Samsung 0.5 : MFE Cisco SCE 2000 4xGBE Installation and Configuration Guide Managing SCE 2000 Configurations...
Page 112: Saving The Configuration Settings
XAMPLE The following example shows the running configuration file. SCE 2000#show running-config #This is a general configuration file (running-config). Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 7 Basic SCE 2000 Platform Operations OL-7824-04...
Page 113 The following example illustrates how to remove all DNS settings from the running configuration. SCE 2000(config)#no ip name-server SCE 2000(config)# OL-7824-04 Managing SCE 2000 Configurations February 2002 Recovering a Previous Configuration Cisco SCE 2000 4xGBE Installation and Configuration Guide (on page 7-8) for...
Page 114: Recovering A Previous Configuration
FastEthernet 0/0 ip address 10.1.5.109 255.255.0.0 interface FastEthernet 0/1 interface FastEthernet 0/2 exit line vty 0 4 exit SCE 2000#copy tffs0:system/prevconf/config.tx1 tffs0:system/config.txt SCE 2000# Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 7 Basic SCE 2000 Platform Operations OL-7824-04...
Page 115: Performing Complex Configurations
The following example shows the commands for system reboot. SCE 2000# reload Are you sure? y the system is about to reboot, this will end your CLI session OL-7824-04 Saving the Configuration Settings (on page 7-6). Cisco SCE 2000 4xGBE Installation and Configuration Guide Performing Complex Configurations...
Page 116: Shutting Down The Sce Platform
Telnet session, and then realizes he/she has no physical access to the SCE 2000 platform. Cisco SCE 2000 4xGBE Installation and Configuration Guide 7-10 Saving the Configuration Settings (on page 7-6).
Page 117: Troubleshooting
Brief description of the problem you are having • Brief explanation of the steps you have taken to isolate and resolve the problem Maintenance agreement or warranty information • OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide C H A P T E R 8...
Page 118: Troubleshooting Tools
There are three tools that will help you to successfully troubleshoot your SCE 2000 installation: CLI Commands for Troubleshooting • • The User Log Check the LEDs • Cisco SCE 2000 4xGBE Installation and Configuration Guide Troubleshooting Strategy for Startup Problems Go to Step 3 Refer to Troubleshooting the firmware package...
Page 119: Cli Commands For Troubleshooting
Telnet sessions (sessions). Following is a sample output from the show telnet command. show telnet sessions There is 1 active telnet session: Index | Source ================ | 10.1.1.201 OL-7824-04 10.1.1.1 Cisco SCE 2000 4xGBE Installation and Configuration Guide Troubleshooting Tools...
Page 120: The User Log
Copying the User Log to an external source • Viewing the User Log • Clearing the User Log • Cisco SCE 2000 4xGBE Installation and Configuration Guide (on page 8-4) for an explanation of commands related to the user log. Chapter 8 Troubleshooting OL-7824-04...
Page 121: Copying The User Log
To view the user log: From the SCE 2000 The user log appears, followed by the SCE 2000 OL-7824-04 and press Enter. (on page 8-5)) prompt, type more user-log and press Enter. Cisco SCE 2000 4xGBE Installation and Configuration Guide Troubleshooting Tools prompt.
Page 122: Clearing The User Log
To view the non-volatile counter for the user-file-log only, use the following command: From the SCE 2000# prompt, type show logger device user-file-log nv- counters and press Enter. The user-file-log non-volatile log counter information appears, followed by the SCE 2000# Cisco SCE 2000 4xGBE Installation and Configuration Guide Chapter 8 Troubleshooting OL-7824-04...
Page 123: Check The Leds
SCE 2000 becomes operational after completing the following process: • Boot is completed • Power self-tests are completed without failure • Platform configuration is applied Cisco SCE 2000 4xGBE Installation and Configuration Guide Troubleshooting Tools Status LED State Orange Flashing green...
Page 124: Problem Solving Using A Subsystems Approach
When you start up the system by turning on the power supply switch, the following should occur: You should immediately hear the fans operating. • Cisco SCE 2000 4xGBE Installation and Configuration Guide Description SCE 2000 is fully operational (as above) but one of the following occurred: •...
Page 125: Troubleshooting The Power Subsystem
If the system powers off due to an environmental shutdown, wait at least one minute before manually Note rebooting the system, or it will pause indefinitely. OL-7824-04 Problem Solving Using a Subsystems Approach (on page 5-1) to verify that the terminal is set correctly and Cisco SCE 2000 4xGBE Installation and Configuration Guide...
Page 126 Faulty power cable. Faulty power supply. Table 8-4 LED Label Power A/B (front panel) Cisco SCE 2000 4xGBE Installation and Configuration Guide 8-10 Troubleshooting the Power Subsystem Possible Solution Turn the power switch to the off position and reseat the power cable in the system.
Page 127: Troubleshooting The Firmware Package Installation
Verify that you are trying to open the correct package file. Delete old and unnecessary files and try the package extraction again. Cisco SCE 2000 4xGBE Installation and Configuration Guide Problem Solving Using a Subsystems Approach 8-11...
Page 128: Troubleshooting The Management Subsystem
• ping to management interface fails Cisco SCE 2000 4xGBE Installation and Configuration Guide 8-12 Troubleshooting the Management Subsystem Possible Cause RJ 45 connector is not connected to the platform or to the network.
Page 129 Check / reconfigure access-list. valid access-list. Initial System Configuration 5-3) Refer to "Access Control Lists" in the Cisco Service Control Engine (SCE) Software Configuration Guide. Cisco SCE 2000 4xGBE Installation and Configuration Guide (on page (on page (on page (on page 8-13...
Page 130: Troubleshooting The Link Interface Subsystem
• Status is WARNING GigabitEthernet 0/# counters (Status LED is flashing orange) • Output counters not incrementing. Cisco SCE 2000 4xGBE Installation and Configuration Guide 8-14 Telnet connection may be timing out. Troubleshooting the Link Interface Subsystem Possible Cause Connector is not connected to the platform or to the network.
Page 131 Auto-negotiation is disabled Check at the SCE 2000 but enabled ("Configuring the GBE Interface at peer. Parameters" on page 6-6) configuration in the SCE 2000 and in peer. Cisco SCE 2000 4xGBE Installation and Configuration Guide auto-negotiation auto-negotiation auto-negotiation 8-15...
Page 133: The External Optical Bypass Module
The External Optical Bypass module is another important component in the Cisco overall carrier- grade solution for high-availability service provider networks. OL-7824-04 Cisco SCE 2000 4xGBE Installation and Configuration Guide A P P E N D I X A...
Page 134: External Optical Bypass Functionality
Note that when the bypass module is active, it puts the SCE 2000 platform into a loop connection, creating a shortcut between the SCE 2000 platform GBE interfaces. Figure A-2: External Optical Bypass Module: Active (in bypass) Cisco SCE 2000 4xGBE Installation and Configuration Guide Appendix A The External Optical Bypass Module...
Page 135: The External Optical Bypass Module Front Panel
To install the External Optical Bypass module: Install the module in the rack. Step 1 Step 2 Cable the module. OL-7824-04 The External Optical Bypass Module Front Panel Cisco SCE 2000 4xGBE Installation and Configuration Guide...
Page 136: Installing The Module In A Rack
If installing two modules, repeat the entire procedure for the second module, with the • following changes: Connect the fiber (steps 3 and 4) to the GBE-2 Line/Cascade ports on the SCE 2000 • platform. Cisco SCE 2000 4xGBE Installation and Configuration Guide Appendix A The External Optical Bypass Module OL-7824-04...
Page 137 SCE 2000 platform. Rx <-> Tx Power up the SCE 2000 platform, as explained in Step 5 Conditions (on page 7-2). OL-7824-04 Installing the External Bypass Module Starting the System and Observing Initial Cisco SCE 2000 4xGBE Installation and Configuration Guide...
Page 138 2000 platform. The “No Bypass” LED should therefore be lit. The figure below illustrates the connections between a SCE 2000 platform and two External Optical Bypass modules. Cisco SCE 2000 4xGBE Installation and Configuration Guide Appendix A The External Optical Bypass Module...
Page 139: Specifications
-10° C to +65° C (14° F to 149° F) -30° C to +70° C (-22° F to 158° F) 12 oz (340 g) Control cable pinouts Pin (D-type side) 7-NC 8-NC 9-NC Shield Cisco SCE 2000 4xGBE Installation and Configuration Guide Specifications Pin (RJ-45 side) Shield...
Page 141: Index
Two SCE 2000s Topology • 6-5 Entry Formats • 5-12 Examining the LEDs • 6-9 External Optical Bypass Functionality • A-2 Fan Module Overview • 4-20 Fiber Specifications • 6-7 Final Tests • 7-3 Cisco SCE 2000 4xGBE Installation and Configuration Guide...
Page 142 Order of Entries • 5-13 Ordering Documentation • ix Organization • vi Overview • 1-1 Cisco SCE 2000 4xGBE Installation and Configuration Guide Performing Complex Configurations • 7-9 Physical Topologies • 3-4 Physically Connected Links Parameter • 3- Power Supply Overview • 4-12 Power Supply Specifications •...
Page 143 Viewing the Counters to Verify that the Network Traffic is Reaching the Device • Viewing the User Log • 8-5 Viewing the User Log Counters • 7-3, 8-6 World Wide Web • ix Cisco SCE 2000 4xGBE Installation and Configuration Guide Index...

Cisco SCE 2000 4xGBE Installation And Configuration Manual

Preface

Overview

Introduction to the SCE Platform

Topology

B

O

Installation and Maintenance

Configuration 5-1

Connecting the Management Interfaces and Performing Initial System Configuration

Cabling the Line Ports and Completing the Installation

50 L

Basic SCE 2000 Platform Operations

Troubleshooting

G

The External Optical Bypass Module

Index

Quick Links

Troubleshooting

Related Manuals for Cisco SCE 2000 4xGBE

Summary of Contents for Cisco SCE 2000 4xGBE

Table of Contents