Input/Output Circuit Specifications; 1: Nfc-50/100 Main Control Board - Honeywell NOTIFIER NFC-50/100 Instruction Manual

Input/Output Circuit Specifications

• System Status LEDs (refer to "Controls and Indicators" on page 17)
• Integral Dress Panel
• Optional TR-CE-B semi-flush trim ring
• Any combination of up to eight (8) of:
– Optional NFC-RM Remote Microphone (includes cabinet).
– Optional NFC-RPU Remote Page Unit (includes cabinet)
– Optional NFC-LOC (includes cabinet)
• Optional NFC-CE6 Circuit Expander
• Optional NFC-BDA-25V amplifier, 50 watts, 25 volts
• Optional NFC-BDA-70V amplifier, 50 watts, 70 volts
• Optional NFC-50DA distributed amplifier, 50 watts
• Optional NFC-125DA distributed amplifier, 125 watts
• Optional NFC-50/100DA distributed amplifier, 50/100 watts
1.2 Input/Output Circuit Specifications
1.2.1 NFC-50/100 Main Control Board
AC Power - TB15
NFC-50/100: 120 VAC, 60 Hz, 3.5 amps (HOT, NEU)
NFC-50/100E: 240 VAC, 50 Hz, 2.0 amps (HOT=HotLeg1, NEU=HotLeg2)
Wire size: minimum #14 AWG (2.00mm
Battery (lead acid only) - J7
Maximum Charging Circuit: Normal Flat Charge - 27.3V @ 2.8 amps
Maximum Charger Capacity: 26 Amp Hour battery. (NFC cabinet holds max. 18 Amp Hour Battery.
Minimum Battery Size: 12 Amp Hour
MNS Active Relay - TB1
Form-C relay contact rating: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive),
Form-C Trouble Relay - TB2
Form-C relay contact rating: 2.0 amps @ 30 VDC (resistive), 0.5 amp @ 30 VAC (resistive).
AC Loss Relay - TB3
Form-C relay contact rating: 2.0 amps @ 30 VDC (resistive), 0.5 amps @ 30 VAC (resistive),
NAC Output - TB19, Terminals 1 (B+), 2 (A+), 3 (A-), & 4 (B-)
One (1) Style Y (Class B) or Style Z (Class A) circuit
Power-limited circuitry (Class 2), supervised
Nominal operating voltage: 24 VDC
Maximum signaling current for special application power: 2.0 amps
Maximum signaling current for regulated power: 200mA
Current limit: fuseless, electronic, power-limited
Maximum wiring impedance: 1 Ω
End-Of-Line Resistor: 4.7 KΩ, ½ watt, (P/N 71252) required for Style Y (Class B) operation
Refer to the Device Compatibility Document for listed compatible devices.
NAC Follower - TB18, Terminals 3 (IN+), 4 (IN-), 1 (OUT+) & 2 (OUT-)
Connections for FACP NAC synchronization trigger signal
Output terminals: pass-through to other system components
Trigger input voltage: 9 to 32 VDC, 24 VDC rated
Input current draw in Alarm condition: 10 mA at rated voltage
Special Application Power (Aux. Power) - TB17 Terminals 1(+) & 2(-)
Up to 500 mA @ 24 VDC of special application power is available for powering addressable modules and associated End-of-Line power
supervision relays.
Power-limited (Class 2) circuitry. Refer to the Device Compatibility Document for a list of compatible devices.
Speaker Volume Control Override - TB23, Terminals 1 (B+), 2 (A+), 3 (A-), & 4 (B-)
Style Y (Class B) or Style Z (Class A) circuit
Special Application power
Power-limited (Class 2) circuitry, supervised
Nominal operating voltage: 24 VDC
Maximum signaling current: 0.25 amps
Current limit: fuseless, electronic, power-limited
End-Of-Line Resistor: 4.7 KΩ, ½ watt, (P/N 71252) required for Style Y (Class B) operation
Notifier FirstCommand Series Manual — P/N LS10001-001NF-E:H 1/8/2018
2
) with 600 V insulation.
Product Description
13