GE GFK-2892F User Manual page 65

The upper word of the status location provides additional status information
VALUE VALUE
decimal Hex DESCRIPTION
(word) (word)
0 0 Command has not been processed.
1 1 Non-specific command failure.
2 2 Null or invalid command block.
Unknown Task ID detected. Task ID should be 132 for Gateway COMMREQs, or 131 for generic
3 3
PROFINET acyclic requests.
4 4 Command completed successfully.
5 5 Incorrect command block length.
10 0x0A Unknown command number.
Invalid PROFINET device number. Number should be in the range 1 through
11 0x0B
MAX_PROFINET_IO_DEVICE_CONNECTIONS (model-specific definition).
PROFINET device is 'undeclared'. The PROFINET device specified in the command block is not
12 0x0C
known to the PNC as currently configured.
13 0x0D PROFINET API value is out of range. The value should be 0 or 1 (always 0 for Gateway requests).
PROFINET slot value is out of range. The value should be in the range 0 through 31 (Gateway
14 0x0E
requests normally use 31, except when using read index 0x0203).
PROFINET subslot value is out of range. Gateway requests always use subslot 1. Generic acyclic
15 0x0F
requests test for a subslot value in range 1 through 32784.
16 0x10 Invalid transfer length specified. Value is either too large, or zero.
17 0x11 PROFINET stack interface failure; read_req call failed at invocation site.
Error returned from PROFINET stack; a generic acyclic request issued a read_req call that
18 0x12
produced a negative confirmation callback.
19 0x13 PROFINET stack interface failure; write_req call failed at invocation site.
Error returned from PROFINET stack; a generic acyclic request issued a write_req call that
20 0x14
produced a negative confirmation callback.
21 0x15 Invalid Genius device number. Value should be in range 0 through 31.
22 0x16 Invalid circuit number. Value should be in range 1 through 32.
Error returned from PROFINET stack; a Gateway request issued a write_req call that produced a
23 0x17
negative confirmation callback.
Error returned from PROFINET stack; a Gateway request issued a read_req call that produced a
24 0x18
negative confirmation callback.
Last write request to the Gateway timed out or had an error. When Gateway status was
25 0x19
checked (via read index 0x0200), the returned value was 2.
Last write request to the Gateway caused a stuck busy result. Gateway status checks (via read
26 0x1A
index 0x0200) have returned a value of 1 for more than 300 msec.
27 0x1B Gateway status check (via read index 0x0200) returned an invalid value (not 0, 1, or 2).
Error returned from PROFINET stack; an attempt to retrieve a Genius Reply from the Gateway
28 0x1C
(via read index 0x0201) produced a negative confirmation callback.
29 0x1D The message status byte associated with a Genius Reply is not 0, indicating a problem.
30 0x1E A Genius Reply does not have the expected length.
A Write Configuration COMMREQ specified a configuration data length that does not match the
31 0x1F
required configuration length for the device.
32 0x20 A Read Block I/O COMMREQ specified an invalid offset value.
33 0x21 An internal error has been detected in the PNC COMMREQ firmware.
34 0x22 The COMMREQ request is not supported by the specified Genius device.
The data type code specified for a Read Data or Write Data COMMREQ does not have a value
35 0x23
recognized by the High-Speed Counter.
GFK-2892F
Chapter 6. COMMREQ/Data_Init_Comm Programming
March 2019 57