Honeywell GSMV4G Installation And Setup Manual page 34

GSMV4G/GSMVCN4G Installation and Setup Guide
PROMPTS
Rpt Zn3 ONLY if
41
Armed (N)_
Zn4 Trigger Type
42
(V+)_
43 Invert Zn4 Y/N
(N)_
44
Restore Zn4 Y/N
(Y)_
Delay Zn4 (secs)
45
(00)
Rpt Zn4 ONLY if
46
Armed (N)_
Zn5 Trigger Type
47
(V+)_
Invert Zn5 Y/N
48
(N)_
Restore Zn5 Y/N
49
(Y)_
Delay Zn5 (secs)
50
(00)_
Rpt Zn5 ONLY if
51
Armed (N)_
Enable Zn6 Y/N
52
(N)_
Zn6 Trigger Type
53
(V+)_
Invert Zn6 Y/N
54
(N)_
Restore Zn6 Y/N
55
(Y)_
Delay Zn6 (secs)
56
(00)_
3-16
4204/
ZONE
OPTIONS
2-4204
TRIG.
[Y], [N]
X X
• (EOLR)
X
• (V+)
• (V–)
[Y], [N]
X
[Y], [N]
X X
[01-15]
X X
[00] = no delay
[Y], [N]
X 2-
4204
only
• (EOLR)
X
• (V+)
• (V–)
[Y], [N]
X
2-
[Y], [N]
X
4204
only
[01-15]
X
2-
4204
[00] = no delay
only
[Y], [N]
X 2-
4204
only
[Y], [N]
4204
only
• (EOLR)
X 4204
• (V+)
only
• (V–)
[Y], [N]
X
4204
only
[Y], [N]
X X
[01-15]
X X
[00] = no delay
DESCRIPTION
Reports alarms on zone 3 ONLY if the conditional
zone (zone 7 in zone trigger mode; zone 4 in 4204
mode; zone 8 in 2-4204 mode) is triggered (armed).
If [N], always reports alarms on zone 3.
4204 mode: If any zone is programmed to "Report
Only if Armed," skip to Prompt 52: "Enable Zn6."
Selects the triggering method for this zone input.
Press the [space] key to scroll through choices.
Inverts the alarm and normal states of the zone 4
trigger; otherwise uses normal input signal.
Enables restore reporting for zone 4.
UL/ULC: Must be set to "Y."
Defines the reporting delay in seconds for
zone 4.
UL/ULC: Must be set to "00."
Reports alarms on zone 4 ONLY if the conditional
zone (zone 7 in zone trigger mode; zone 8 in 2-4204
mode) is triggered (armed).
If [N], always reports alarms on zone 4.
Selects the triggering method for this zone input.
Press the [space] key to scroll through choices.
Inverts the alarm and normal states of the zone 5
trigger; otherwise uses normal input signal.
Enables restore reporting for zone 5.
UL/ULC: Must be set to "Y."
Defines the reporting delay in seconds for
zone 5.
UL/ULC: Must be set to "00."
Reports alarms on zone 5 ONLY if the conditional
zone (zone 7 in zone trigger mode; zone 8 in 2-4204
mode) is triggered (armed).
If [N], always reports alarms on zone 5.
Enables alarm reporting for zone 6.
If [N], skip to Prompt 58: "Enable Zn7."
Selects the triggering method for this zone input.
Press the [space] key to scroll through choices.
Inverts the alarm and normal states of the zone 6
trigger; otherwise uses normal input signal.
Enables restore reporting for zone 6.
UL: Must be set to "Y."
Defines the reporting delay in seconds for
zone 6.
UL/ULC: Must be set to "00."