Toro Workman 07142 Operator's Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower Accessories
  5. 07142
  6. Operator's manual
Toro Workman 07142 Operator's Manual

Toro Workman 07142 Operator's Manual

Cab kit gtx utility vehicle
Hide thumbs Also See for Workman 07142:
Table of Contents

Advertisement

Quick Links

Download this manual
Cab Kit
Workman
Model No. 07142—Serial No. 413000000 and Up
Important:
The Power Converter Kit is required
to use the cab on a Workman GTX Electric utility
vehicle. Contact your authorized Toro distributor
for more information.
Important:
The Spring Kit is required to use
the cab on a Workman GTX utility vehicle. The
Spring Kit should be installed only by qualified
Toro Service Technicians using approved tools.
Improper removal, disassembly, or installation of
the spring assembly poses a danger to you and
bystanders. Please contact your authorized Toro
distributor for the appropriate tools and proper
installation of this kit.
Safety
WARNING
The compressed spring in the spring and
shock assembly represents a stored-energy
hazard. If the spring is not properly retained
during compression or removal, it can injure
you and/or bystanders.
• Always use the approved Toro
spring-compression tool to compress the
spring in a secure position when removing
the retention collar.
• Always use care when removing pressure
from the compressed spring.
© 2023—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
GTX Utility Vehicle
Register at www.Toro.com.
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
133-1016
1. Warning—read the
Operator's Manual; wear
the seatbelt, and avoid
tipping the machine.
Original Instructions (EN)
Printed in the USA
All Rights Reserved
Form No. 3464-614 Rev A
Operator's Manual
decal133-1016
2. Warning—wear hearing
protection.
*3464-614*

Advertisement

Table of Contents
loading

Related Manuals for Toro Workman 07142

Summary of Contents for Toro Workman 07142

  • Page 1 Important: The Power Converter Kit is required to use the cab on a Workman GTX Electric utility Decals vehicle. Contact your authorized Toro distributor for more information. Safety decals and instructions are easily visible to the operator and are Important:...
  • Page 2 decal131-8410 131-8410 1. Fire hazard—shut off the engine before fueling. decal120-9570 120-9570 decal133-1017 133-1017 1. Warning—stay away from moving parts, keep all guards and shields in place. 1. Do not repair or revise—read the Operator's Manual. decal145-7727 145-7727 decal130-5964 130-5964 1.

  • Page 3: Table Of Contents

    Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. Remove the strut assembly (for – No parts required machines with Serial No. 403448001 and before only). Install the springs (for machines with Spring Serial No.
  • Page 4 Procedure Description Qty. Fuse (5 A) Install the fuse (5 A) and apply the decal. Decal 145-7727 Cab adapter wire harness—for electric machines with Serial No. 403448001 Install the cab adapter wire harness. and after only. Preparing the Machine No Parts Required Procedure Park the machine on a level surface, set the parking brake, shut off the engine, and remove the key.

  • Page 5: Spring

    g038284 Figure 1 Some parts not shown for clarity 1. Hex-head bolt (1/2 x 2-1/4 inches) 6. Flange nut (3/8 inch)—from the control arm 2. Locknut (1/2 inch) 7. Flange nut (3/8 inch)—from the spindle 3. Collar 8. Hex-head bolt (3/8 x 3-1/2 inches)—from the control arm 4.

  • Page 6: No Parts Required

    No Parts Required Procedure Procedure Install strut assembly to the machine. Use an approved Toro spring-compression tool to remove and install springs of the strut assembly. Secure the upper portion of the strut assembly Contact your authorized Toro distributor. to the frame using the upper, hex-head bolt (1/2...

  • Page 7: Floor-Plate Support

    Use a floor jack under the frame to support the front of the machine (Figure Installing the Supports Parts needed for this procedure: Floor-plate support Flange-head bolt (5/16 x 1-1/4 inches) Flange nut (5/16 inch) Left cab support Right cab support Hex-head bolt (3/8 x 1-1/4 inch) g038334 Figure 3...
  • Page 8 Install a new floor-plate support using 8 Using the new floor-plate supports as a guide, flange-head bolts (5/16 x 1-1/4 inches) and 8 drill 3 holes (3/8-inch diameter) into each floor flange nuts (5/16 inch) as shown in Figure plate (Figure Note: Important:...

  • Page 9: Cab Frame

    Remove the 3 screws and 3 nuts securing the left handhold, and remove it (Figure Installing the Cab Parts needed for this procedure: Cab frame Back foam seal Back foam seal carpet g037177 Figure 9 Flange-head bolt (5/16 x 1-1/4 inches) Flange nut (5/16 inch) 1.

  • Page 10: Hex-Head Bolt (3/8 X 1-1/4 Inches)

    Lift the cab frame using the lift points and place Secure the back of the cab frame to the left and it on the machine (Figure 11). right supports using 4 flange-head bolts (5/16 x 1-1/4 inches), 2 support plates, 4 flat washers, and 4 flange nuts (5/16 inch) as shown in Figure Note:...
  • Page 11 Fuse (15 A) For Electric Machines Important: The Power Converter Kit is required to use the cab on a Workman GTX Electric utility vehicle. Contact your authorized Toro distributor for more information. Install the new fuse block as follows: g035254 Figure 15 •...
  • Page 12 • For machines with Serial No. 403448001 Route the wire harness behind the cab and and after, secure the new fuse block using under the seat, and secure the clip on the wire the 2 hex-washer head screws (#10 x 3/4 harness to the side panel (Figure 19).
  • Page 13 Connect the remaining wire to the fused wire on Install the black terminal ring to the ground block the new fuse block (Figure 17). on the machine (Figure 22). Lower the bed and connect the battery; refer to Install the red power wire into an empty slot on the Operator’s Manual.
  • Page 14 Installing the Fuse (5 A) and Installing the Cab Adapter Applying the Decal Wire Harness Electric Machines Only Parts needed for this procedure: Fuse (5 A) Parts needed for this procedure: Decal 145-7727 Cab adapter wire harness—for electric machines with Serial No. 403448001 and after only. Procedure Install the fuse into the opening in the fuse block Procedure...
  • Page 15 Connect the loose square socket on the power converter wire harness to the cab adapter wire harness (Figure 28). g299566 Figure 26 1. 4-pin socket on the cab 2. 4-pin plug on the main adapter wire harness. harness. g299581 Figure 28 Connect the 4-pin plug on the cab adapter wire 1.
  • Page 16 Product Overview Controls Control Panel Windshield-Wiper Switch Click the switch forward to activate the windshield wipers (Figure 29). g026274 Figure 29 1. Windshield-wiper control 2. Light switch Light Switch Push the left or right side of the light plate to turn on the cab light (Figure 29).

Table of Contents