Download
Share
Print this page
Toro 07320 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Toro Manuals
  4. Lawn Mower Accessories
  5. 07320
  6. Installation instructions manual
Toro 07320 Installation Instructions Manual

Toro 07320 Installation Instructions Manual

Hide thumbs Also See for 07320:

Advertisement

Quick Links

Download this manual
Cab Kit
Workman
Model No. 07320—Serial No. 315000001 and Up
Safety
WARNING
CALIFORNIA
Proposition 65 Warning
This product contains a chemical
or chemicals known to the State of
California to cause cancer, birth defects,
or reproductive harm.
Safety and Instructional
Decals
Safety decals and instructions are
easily visible to the operator and are
located near any area of potential
danger. Replace any decal that is
damaged or missing.
1. Do not repair or revise—read the Operator's Manual.
© 2017—The Toro® Company
8111 Lyndale Avenue South
Bloomington, MN 55420
®
MD/MDE/MDX/MDXD Utility Vehicle
93-9850
Register at www.Toro.com.
1. Warning—read the Operator's Manual; wear the seat belt
when seated in the operator's position; avoid tipping the
machine.
2. Warning—wear hearing protection.
decal93-9850
1. Warning—in the event of an emergency 1) Pull the locking
pin out of each hinge; 2) Push the front window out to exit.
Form No. 3389-927 Rev B
Installation Instructions
117-4955
130-5964
Original Instructions (EN)
All Rights Reserved *3389-927* B
Printed in the USA
decal117-4955
decal130-5964

Advertisement

loading

Related Manuals for Toro 07320

Summary of Contents for Toro 07320

  • Page 1 Form No. 3389-927 Rev B Cab Kit Workman ® MD/MDE/MDX/MDXD Utility Vehicle Model No. 07320—Serial No. 315000001 and Up Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
  • Page 2 decal130-5439 130-5439 1. Read the Operator’s Manual for information on fuses. 4. Windshield spray 2. Windshield wiper (15 A) 5. Windshield wiper 3. Lights (15 A)

  • Page 3: Installation

    Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. – No parts required Prepare the machine. – No parts required Remove the ROPS assembly. Compression spring Install the compression spring. Floor mount Nut (3/8 inch) Bolt (3/8 x 1 inch) Bolt (5/16 inch)

  • Page 4: Preparing The Machine

    Operator’s Manual. Important: For 2015 and older models, you must 4. Shut off the engine and remove the key. order the 2 compression springs (Toro Part No. 5. Disconnect the battery; refer to the Operator’s 117-4847) for installation. Manual.
  • Page 5 Installing the Floor Mounts Installing the Cab Frame Parts needed for this procedure: Parts needed for this procedure: Floor mount Cab frame Nut (3/8 inch) Bolts (3/8 x 7/8 inch) Bolt (3/8 x 1 inch) Bolt (3/8 x 3/4 inch) Bolt (5/16 inch) Nuts (3/8 inch) Nut (5/16 inch)

  • Page 6: Installing The Side Panels

    Installing the Side Panels Installing the Seat Belts Parts needed for this procedure: Parts needed for this procedure: Side-plate panels Seat-belt anchors Bolts (1/4 inch) Bolts (3/8 x 3/4 inch) Side-plate foam panel Nuts (3/8 inch) Seat belt receiver end Bolt (7/16 inch) Installing the Side-Plate Panels Nut (7/16 inch)
  • Page 7 5. Secure the left and right seat belt anchor to the front frame with 4 bolts (3/8 x 3/4 inch) and 4 nuts (3/8 inch) as shown in Figure g026314 Figure 10 9. Mount the receiver end of each seat belt assembly to each seat belt anchor with a bolt (7/16 inch) and nut (7/16 inch) as shown in g026308...
  • Page 8 Connect the ring terminal on the harness to the grounding block and insert the fuse block connector into an available fuse block connection (Figure 12). If a fuse block connection is not available, add a fuse block to the fuse block grouping. Contact your Routing the Wire Harness Authorized Service Dealer for more information.

  • Page 9: Product Overview

    Product Overview Controls Control Panel Windshield Wiper Switch Push the top of the switch to activate the windshield wipers (Figure 13). g026274 Figure 13 1. Windshield wiper control 2. Light switch Light Switch Push the light plate to turn on the light (Figure 13).
  • Page 10 Notes:...
  • Page 11 Notes:...
  • Page 12 The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.